Ramesh, Do you see cisco neighbor in "show ipv6 neighbors"?
Thanks, Nilesh On 4/4/10 11:32 PM, "Ramesh Karki" <[email protected]> wrote: > Hi Antonio, > > yes, interface ge-0/0/0 is only configure for ospf3 and interface fe-0/1/0 > is configued for dual-stack. > > Here, I have listed the required configuation as you have asked. > > scenario > Cisco-rtr ------------------ ge-0/0/0 (M10i) fe-0/1/0 ----------------- > Cisco-rtr > ospf3 dual-stack > ospf2 and ospf3 > > M10i config > > show configuration protocols ospf > preference 110; > area 0.0.0.10 { > interface lo0.0 { > passive; > } > interface fe-0/1/0.0; > interface fxp0.0 { > disable; > } > interface fe-0/1/1.0 { > passive; > } > interface fe-0/1/2.0 { > passive; > } > interface fe-0/3/0.0 { > passive; > } > } > > > show configuration protocols ospf3 > preference 110; > area 0.0.0.10 { > interface ge-0/0/0.0; > interface lo0.0 { > passive; > } > interface fe-0/3/1.0 { > passive; > } > interface fe-0/1/0.0; > > > > show ospf interface > Interface State Area DR ID BDR ID > Nbrs > fe-0/1/0.0 BDR 0.0.0.10 x.x.192.4 x.x.192.1 > 1 > fe-0/1/1.0 DRother 0.0.0.10 0.0.0.0 0.0.0.0 > 0 > fe-0/1/2.0 DRother 0.0.0.10 0.0.0.0 0.0.0.0 > 0 > fe-0/3/0.0 DRother 0.0.0.10 0.0.0.0 0.0.0.0 > 0 > lo0.0 DRother 0.0.0.10 0.0.0.0 0.0.0.0 > 0 > > > > > show ospf3 interface > OSPF instance is not running > > > The neighbor cisco devices, one connected to m10i fe-0/1/0 and another cisco > device connected to M10i ge-0/0/0 > > cisco config output connected to M10i fe-0/1/0 > > #sh run | be ^ipv6 router ospf > ipv6 router ospf 1 > router-id x.x.192.4 > log-adjacency-changes > passive-interface default > no passive-interface FastEthernet0/0 > > > #sh run int fa0/0 > Building configuration... > > Current configuration : 284 bytes > ! > interface FastEthernet0/0 > description *** *** > ip address x.x.193.4 255.255.255.240 > no keepalive > duplex full > ipv6 address abcd:3800:2:1::2/126 > ipv6 enable > ipv6 ospf 1 area 10 > no cdp enable > no clns route-cache > end > > #sh ipv6 ospf int > FastEthernet0/0 is up, line protocol is up > Link Local Address FE80::20C:31FF:FE95:A400, Interface ID 3 > Area 10, Process ID 1, Instance ID 0, Router ID x.x.192.4 > Network Type BROADCAST, Cost: 1 > Transmit Delay is 1 sec, State DR, Priority 1 > Designated Router (ID) x.x.192.4, local address FE80::20C:31FF:FE95:A400 > No backup designated router on this network > Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 > Hello due in 00:00:00 > Index 1/1/2, flood queue length 0 > Next 0x0(0)/0x0(0)/0x0(0) > Last flood scan length is 0, maximum is 0 > Last flood scan time is 0 msec, maximum is 0 msec > Neighbor Count is 0, Adjacent neighbor count is 0 > Suppress hello for 0 neighbor(s) > Loopback6 is up, line protocol is up > Link Local Address FE80::20C:31FF:FE95:A400, Interface ID 15 > Area 10, Process ID 1, Instance ID 0, Router ID x.x.192.4 > Network Type LOOPBACK, Cost: 1 > Loopback interface is treated as a stub Host > > > cisco config output connected to M10i ge-0/0/0 > > #sh run int fa0/0 > Building configuration... > > Current configuration : 258 bytes > ! > interface FastEthernet0/0 > description *** *** > ip address x.x.193.72 255.255.255.192 > ip route-cache flow > duplex auto > speed auto > ipv6 address abcd:3800:1:1::2/64 > ipv6 enable > ipv6 ospf 1 area 10 > no cdp enable > end > > > #sh run | be ^ipv6 router ospf > ipv6 router ospf 1 > router-id x.x.192.2 > log-adjacency-changes > passive-interface default > no passive-interface FastEthernet0/0 > > > > #sh ipv6 int fa0/0 > FastEthernet0/0 is up, line protocol is up > IPv6 is enabled, link-local address is FE80::218:73FF:FE46:1232 > Description: *** *** > Global unicast address(es): > abcd:3800:1:1::2, subnet is abcd:3800:1:1::/64 > Joined group address(es): > FF02::1 > FF02::2 > FF02::5 > FF02::6 > FF02::1:FF00:2 > FF02::1:FF46:1232 > MTU is 1500 bytes > ICMP error messages limited to one every 100 milliseconds > ICMP redirects are enabled > ND DAD is enabled, number of DAD attempts: 1 > ND reachable time is 30000 milliseconds > ND advertised reachable time is 0 milliseconds > ND advertised retransmit interval is 0 milliseconds > ND router advertisements are sent every 200 seconds > ND router advertisements live for 1800 seconds > Hosts use stateless autoconfig for addresses. > > > Have a query that is, why even the static route didn't worked on the box? > > Thank you, > Ramesh > > > On Sun, Apr 4, 2010 at 6:56 PM, Antonio Querubin <[email protected]> wrote: > >> On Sun, 4 Apr 2010, Ramesh Karki wrote: >> >> As I have already mentioned, the same interface fe-0/1/0 has been >>> configured >>> to run both ospf and ospf3 and there is no any issue on ospf v4 from the >>> beginning. >>> >>> show ospf interface fe-0/1/0.0 >>>> >>> Interface State Area DR ID BDR ID >>> Nbrs >>> fe-0/1/0.0 BDR 0.0.0.10 x.x.192.4 x.x.192.1 >>> 1 >>> >>> but the same interface configured for ospf3 outcome is unexpected. >>> >>> show ospf3 interface fe-0/1/0.0 >>>> >>> OSPF instance is not running >>> >> >> Reviewing what you've posted so far I only see a partial ospf3 config for >> ge-0/0/0.0 >> >> Could you please post the complete output of: >> >> show configuration protocols ospf >> show configuration protocols ospf3 >> show ospf interface >> show ospf3 interface >> >> Then for your dual-stack interfaces which should be running ospf and ospf3 >> do: >> >> show configuration interfaces >> >> On your ciscos which have a working ospf3 config do >> >> show running-config | begin ipv6 router ospf >> show ipv6 ospf interface >> >> show running-config interface <each dual-stack interface that faces a >> juniper> >> >> >> Antonio Querubin >> 808-545-5282 x3003 >> e-mail/xmpp: [email protected] >> > _______________________________________________ > juniper-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/juniper-nsp _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
