OK it completed with -j2 without problem - there is wnother error now
present in command line I get:
machinekit@mksocfpga:~$ machinekit ~/myconfig/mksocfpga.ini
MACHINEKIT - 0.1
Machine configuration directory is '/home/machinekit/myconfig'
Machine configuration file is 'mksocfpga.ini'
Starting Machinekit...
io started
halcmd loadusr io started
mksocfpga.hal:40: rc=-1: hal_call_usrfunct(newinst,--
config="firmware=socfpga/dtbo/DE0_Nano_SoC_DB25.7I76_7I85S_GPIO_GPIO.dtbo
num_stepgens=4 num_encoders=1 num_mencoders=4") failed: -1 - Operation not
permitted
Shutting down and cleaning up Machinekit...
Cleanup done
Machinekit terminated with an error. You can find more information in the
log:
/home/machinekit/linuxcnc_debug.txt
and
/home/machinekit/linuxcnc_print.txt
as well as in the output of the shell command 'dmesg' and in the terminal
machinekit@mksocfpga:~$ DEBUG=5
machinekit@mksocfpga:~$ export DEBUG=5
machinekit@mksocfpga:~$ machinekit ~/myconfig/mksocfpga.ini
MACHINEKIT - 0.1
Machine configuration directory is '/home/machinekit/myconfig'
Machine configuration file is 'mksocfpga.ini'
Starting Machinekit...
io started
<commandline>:0: Component 'iocontrol' ready
<commandline>:0: Program 'io' started
halcmd loadusr io started
mksocfpga.hal:29: Realtime module 'trivkins' loaded
mksocfpga.hal:33: Realtime module 'tp' loaded
mksocfpga.hal:37: Realtime module 'hostmot2' loaded
mksocfpga.hal:40: Realtime module 'hm2_soc_ol' loaded
mksocfpga.hal:40: rc=-1: hal_call_usrfunct(newinst,--
config="firmware=socfpga/dtbo/DE0_Nano_SoC_DB25.7I76_7I85S_GPIO_GPIO.dtbo
num_stepgens=4 num_encoders=1 num_mencoders=4") failed: -1 - Operation not
permitted
Shutting down and cleaning up Machinekit...
<commandline>:0: Realtime threads stopped
<commandline>:0: Realtime module 'hm2_soc_ol' unloaded
<commandline>:0: Realtime module 'hostmot2' unloaded
<commandline>:0: Realtime module 'tp' unloaded
<commandline>:0: Realtime module 'trivkins' unloaded
<commandline>:0: Realtime threads stopped
Cleanup done
Machinekit terminated with an error. You can find more information in the
log:
/home/machinekit/linuxcnc_debug.txt
and
/home/machinekit/linuxcnc_print.txt
as well as in the output of the shell command 'dmesg' and in the terminal
In dmesg Iget:
[ 4054.891575] fpga_manager fpga0: writing
socfpga/DE0_Nano_SoC_DB25.7I76_7I85S_GPIO_GPIO.rbf to Altera SOCFPGA FPGA
Manager
[ 4055.106816] fpga_manager fpga0: Error after writing image data to FPGA
[ 4055.113936] failed to load fpga image
Dne torek, 14. februar 2017 15.29.07 UTC+1 je oseba Charles Steinkuehler
napisala:
>
> On 2/14/2017 8:12 AM, [email protected] <javascript:> wrote:
> >
> > I found that only an actual swap partition of at least 512MB worked
> reliably
> > using *make -j2*
>
> I usually go even farther and run:
>
> make -j1
>
> ...unless I'm building on something with more memory. It is also
> pretty easy to cross-build if you have a decent x86 machine that runs
> Docker, but you'd have to copy over the build directory (the kernel
> doesn't have dnotify enabled so won't support NFS).
>
> --
> Charles Steinkuehler
> [email protected] <javascript:>
>
--
website: http://www.machinekit.io blog: http://blog.machinekit.io github:
https://github.com/machinekit
---
You received this message because you are subscribed to the Google Groups
"Machinekit" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.
