Try using diskpart manually with F8 in WinPe, create and pre-formatted drive.
This happend to before, after the diskpart is was ok. The TS-engine could store any data, after the format it could. Hopefully this helps. Sent from my iPhone Mvg, David van Beek KPN Consulting > On 23 aug. 2014, at 16:31, Daniel Ratliff <[email protected]> wrote: > > Not sure, but worst case just go back into the settings and delete and > recreate the HDD. > > From: [email protected] [mailto:[email protected]] > On Behalf Of Denzik, Josh > Sent: Saturday, August 23, 2014 10:28 AM > To: [email protected] > Subject: RE: [MDT-OSD] MDT 2013 Task Sequence Failing After Apply OS on VM > Ware Workstation 10 > > Forgive me I am little frayed at the moment, when I create the VM is there an > option for that? > > From: [email protected] [mailto:[email protected]] > On Behalf Of Daniel Ratliff > Sent: Saturday, August 23, 2014 10:18 AM > To: [email protected] > Subject: RE: [MDT-OSD] MDT 2013 Task Sequence Failing After Apply OS on VM > Ware Workstation 10 > > No, your disk configuration on your VM. Make sure you are using ‘thick > provisioned’, I think that is what VMware calls it. > > From: [email protected] [mailto:[email protected]] > On Behalf Of Denzik, Josh > Sent: Saturday, August 23, 2014 10:15 AM > To: [email protected] > Subject: RE: [MDT-OSD] MDT 2013 Task Sequence Failing After Apply OS on VM > Ware Workstation 10 > > I have a slave installed on my machine that is fixed D: drive, that is where > I am running it from. > > From: [email protected] [mailto:[email protected]] > On Behalf Of Daniel Ratliff > Sent: Saturday, August 23, 2014 10:00 AM > To: '[email protected]'; '[email protected]' > Subject: RE: [MDT-OSD] MDT 2013 Task Sequence Failing After Apply OS on VM > Ware Workstation 10 > > Are you using a fixed disk or dynamic? > > I have had similar issues in the past with dynamic disks. > > -----Original Message----- > From: Denzik, Josh [[email protected]] > Sent: Saturday, August 23, 2014 09:24 AM Eastern Standard Time > To: [email protected] > Subject: [MDT-OSD] MDT 2013 Task Sequence Failing After Apply OS on VM Ware > Workstation 10 > > > All, > > I setup my new deployment share, created my client task sequence. I am using > VM Ware Workstation 10. HD settings are SCSI. With 40 GB Drive. I am trying > to apply win 7 x64. This was working on a previous deployment I had setup, > but I had to create a new deployment share and new task sequences. Are there > any settings for VM Ware Workstation 10 I should be aware of? Any Drivers I > am missing? Any obvious settings in the ts I need to check? I am using WinPE > 5.0. Please help I am very frustrated…Any help would be greatly appreciated. > J Below is a snippet from the log. > > <image001.png> > > The information transmitted is intended only for the person or entity to > which it is addressed > and may contain CONFIDENTIAL material. If you receive this > material/information in error, > please contact the sender and delete or destroy the material/information. > > The information transmitted is intended only for the person or entity to > which it is addressed > and may contain CONFIDENTIAL material. If you receive this > material/information in error, > please contact the sender and delete or destroy the material/information. > > The information transmitted is intended only for the person or entity to > which it is addressed > and may contain CONFIDENTIAL material. If you receive this > material/information in error, > please contact the sender and delete or destroy the material/information.
