On Fri, Sep 17, 2010 at 6:37 AM, Samuel Xu <[email protected]> wrote: > Thanks Amit Pundir! > Does it mean I should not follow > http://wiki.meego.com/ARM/Meego_on_the_Beagle, and should follow > http://wiki.meego.com/ARM/Meego_on_Beagleboard_from_scratch? I guess
I can't comment on that since I didn't try http://wiki.meego.com/ARM/Meego_on_the_Beagle > Meego_on_Beagleboard_from_scratch page is guide us to self-build a > kernel > and rootfs, instead of quick installing a pre-compiled one for N900. > It will be better for you to go from scratch since you won't be able to get the UI up on Devkit8000 with the pre-built images available for BeagleBoard from here http://wiki.meego.com/ARM/Meego_on_the_Beagle because SGX(OpenGL ES) will not take off out of the box. In case you have to go with the pre-built images, you need to remove the previous SGX installation(modules + init script + libraries) and build the fresh SGX modules for Devkit8000 kernel and install them in your Rootfs along with the libraries. Regards, Amit Pundir > Is my understanding correctly? > > Samuel > > 2010/9/16 Amit Pundir <[email protected]>: >> On Thu, Sep 16, 2010 at 3:35 PM, Samuel Xu <[email protected]> wrote: >>> Hi: >>> I hit the simiar issue(booted, while no X) as vijay singh, when I want >>> to run MeeGo on top of devkit8000. >>> >>> I followed <Steps to modify an N900 image for BeagleBoard > at >>> http://wiki.meego.com/ARM/Meego_on_the_Beagle, using >>> http://repo.meego.com/MeeGo/releases/1.0/core/images/meego-n900-open-armv7l/meego-n900-open-armv7l-1.0.0.20100525.1-sda.raw.bz2 >>> and http://wiki.meego.com/images/Meego-beagle-kernel.tar.bz2 >>> >>> My u-boot cmd is: >>> setenv bootcmd 'mmcinit; fatload mmc 0 0x82000000 uImage;bootm 0x82000000' >>> setenv bootargs 'mem=256M console=ttyS2,115200n8 mpurate=600 >>> buddy=unknown vram=12M omapfb.mode=dvi:1024x768mr...@60 >>> omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait' >>> boot >>> >> >> Hi, I got it running few weeks back by following the instructions from >> here http://wiki.meego.com/ARM/Meego_on_Beagleboard_from_scratch >> >> I hope things will work out fine for you as well. >> >>> MeeGo can boot into shell in serial cmd prompt. while I found the >>> external monitor (connected via HDMI=>DVI) is black after a blinking. >>> >>> Boot information(boot-log) is attached. I also tried startx from >>> serial cmd shell, I know it is not reasonable to start x from this >>> shell, while the attached debug information(startx) might be useful. >>> >>> Appreciate guide on how to process to start X on my devkit8000. >>> >> >> If you do exactly the same as mentioned in that wiki page, you will >> land safely :) because I made some mistakes while copying the rootfs >> to MMC card and that gave a set of permission errors. Due to which my >> UI was not coming up. >> >> Make sure you are copying the rootfs onto the card as mentioned in the >> wiki to retain the same set of permissions/privileges as needed. >> >> Regards, >> Amit Pundir >> >>> Samuel >>> >> > _______________________________________________ MeeGo-dev mailing list [email protected] http://lists.meego.com/listinfo/meego-dev
