Hi there,
chris i think what you say that is much easier to do and its not a big hassel.i
will just grind off the tapered tube and weld them the other way round.
by the way do i have to swap the tube too from left too right.
mohit.
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of Chris King
Sent: Monday, March 21, 2005 6:03 PM
To: [email protected]
Subject: Re: Cross member...
Yeah mohit you dont cut the actual crossmember, you need to make up a jig to
hold the big bolts in their correct position, then grind away the welds
around the tapered tubes. You then reverse these and reweld using the jig to
align them correctly
----- Original Message -----
From: "Mohit K. Autar" <[EMAIL PROTECTED]>
To: <[email protected]>
Sent: Monday, March 21, 2005 12:32 PM
Subject: RE: Cross member...
yes i do have one.actually i pulled that fj20 engine out from it.but that
cross member is slightly shorter then the 510.
mohit.
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of Zac Campbell
Sent: Monday, March 21, 2005 1:10 PM
To: [email protected]
Subject: Re: Cross member...
Are you sure about that Rick? I've never seen it done like that.
In the popular off the shelf kits, I am pretty sure that they just ground
off
the washers that hold the control arm studs in place then moved the stud
around
to the opposite side and rewelded it in place. Then refit it to the car and
LCAs.
Mohit, do you have Datsun 810 there?
zac
Quoting sss510 <[EMAIL PROTECTED]>:
> Mohit.
> You need to fit a reversed Xmember.
>
> Your Xmember needs to be cut twice, and the centre peice needs to be re
> welded back into place, but with the middle section facing the other
> direction mate.
>
> ---------------------/____________\---------------------
>
>
> --------------------\______________/-------------------
>
> Very hard to show you here, but I hope you get what I meen.
>
> Rick White.
> ----- Original Message -----
> From: Mohit K. Autar
> To: Membersozdat (E-mail)
> Sent: Monday, March 21, 2005 4:07 AM
> Subject: Cross member...
>
>
>
> Hi guys,
>
> I have a problem and i need ideas.im fitting a FJ20 in my 510 and i
> removed the cross member yesterday and tried to fit it the other way
> around.but only the two no.14 bolts line up first as i have to make the
> hole
> slightly bigger for the other two holes.is that normal with you guys.
>
> Now how do i fit the lower arm.as its bolt which fits one way and it
> cant
> fit from the other side.what i think is ,do i have to make the hole bigger
> on
> the rear end and on the front side i have weld a washer of the size of the
> bolt to keep it in place.
>
>
> cheers
> mohit.
>
>
>
> ------------------------------------------------------------------------------
>
>
> No virus found in this outgoing message.
> Checked by AVG Anti-Virus.
> Version: 7.0.308 / Virus Database: 266.7.4 - Release Date: 18/03/2005
>
--
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.7.4 - Release Date: 18/03/2005
--
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.7.4 - Release Date: 18/03/2005
--------------------------------------------------------------------------------
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.7.4 - Release Date: 18/03/2005
--
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.7.4 - Release Date: 18/03/2005
--
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.7.4 - Release Date: 18/03/2005
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [email protected]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
This email and any files transmitted with it are confidential and intended
solely for the use of the individual or entity to whom they are addressed. If
you have received this mail in error, please notify the System Administrator.
Please note that any views or opinions presented in this mail are solely those
of the author and do not necessarily represent those of the Institute. Finally
the recipient should check this mail and any attachment for the presence of
viruses. FIT has a virus detection in place and makes every reasonable effort
to ensure that this message is free from viruses. FIT accepts no liability for
any damage caused by any virus transmitted by this mail
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.7.4 - Release Date: 18/03/2005
