On 21.3.2017 03:26, Jean-Francois Dagenais wrote: > >> On Mar 20, 2017, at 21:48, Jean-Francois Dagenais <[email protected]> >> wrote: >> >> >>> On Mar 20, 2017, at 16:29, Jean-Francois Dagenais <[email protected]> >>> wrote: >>> >>> So please advise, I was under the impression that I needed recent commits in >>> u-boot-xlnx related to SD for booting on it. Should I use another specific >>> version of u-boot-xlnx? Again, just want to get past all that and execute >>> the >>> kernel so the rest of the teams can progress. >> > > Alright, so quick update before I head out til tomorrow... > > I disabled GEM in the 1.0 defconfig (don't need it) and removed the 0.3 > version check to see where it would fail next... > > <debug_uart> Debug uart enabled > > U-Boot SPL 2017.01 (Mar 20 2017 - 22:19:03) > EL Level: EL3 > Trying to boot from MMC1 > reading u-boot.bin > reading atf-uboot.ub > reading atf-uboot.ub > NOTICE: ATF running on XCZU9EG/silicon v3/RTL5.1 at 0xfffea000, with PMU > firmware > NOTICE: BL31: Secure code at 0x0 > NOTICE: BL31: Non secure code at 0x8000000 > NOTICE: BL31: v1.2(release):a9e3716 > NOTICE: BL31: Built : 16:41:21, Mar 9 2017 > PMUFW: PmMmioRead: (NODE_APU) addr=0xFF5E0074, value=0x1010F00 > PMUFW: PmMmioRead: (NODE_APU) addr=0xFF5E0020, value=0x15A00 > > > U-Boot 2017.01 (Mar 20 2017 - 22:25:08 -0400) Xilinx ZynqMP ZCU102 rev1.0 > > I2C: ready > DRAM: 4 GiB > EL Level: EL2 > Chip ID: xczuunknown > PMUFW: PmMmioRead: (NODE_APU) addr=0xFF5E0074, value=0x1010F00 > PMUFW: PmMmioRead: (NODE_APU) addr=0xFF5E0020, value=0x15A00 > MMC: PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180358, mask=0x40000, > value=0x40000 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0x2000000, > value=0x2000000 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0x1000000, > value=0x1000000 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0xFF0000, value=0x150000 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0x2000000, value=0x0 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180318, mask=0x400000, value=0x400000 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180318, mask=0x3F0000, value=0x50000 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180358, mask=0x40000, value=0x0 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180358, mask=0x40000, value=0x40000 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0x2000000, > value=0x2000000 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0x1000000, > value=0x1000000 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0xFF0000, value=0x150000 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0x2000000, value=0x0 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180318, mask=0x400000, value=0x400000 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180318, mask=0x3F0000, value=0x50000 > PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180358, mask=0x40000, value=0x0 > sdhci@ff170000: 0 (SD) > reading uboot.env > > ** Unable to read "uboot.env" from mmc0:1 ** > Using default environment > > In: serial@ff000000 > Out: serial@ff000000 > Err: serial@ff000000 > PMUFW: PmMmioRead: (NODE_APU) ERROR: access denied for address 0xFF5E0200 > initcall sequence 000000007ff8c2a0 failed at call 0000000008002d54 (err=-22) > ### ERROR ### Please RESET the board ### >
We are not testing u-boot without pmufw because it is mandatory now. It worked before that's why I expect with some changes it will continue to work with some exception but for us doesn't make sense to test or support this. Thanks, Michal -- _______________________________________________ meta-xilinx mailing list [email protected] https://lists.yoctoproject.org/listinfo/meta-xilinx
