From: Brian Simmons <[email protected]>
Subject: Re: NEOTEK: problem with my Neotek Elan II
To: [email protected]
Date: Tuesday, January 6, 2009, 3:43 PM
Ok Ike , thanks alot for your help , Ill try replacing the
op-amp first and go from there.
-Brian
--- On Tue, 1/6/09, Ike Zimbel
<[email protected]> wrote:
From: Ike Zimbel <[email protected]>
Subject: Re: NEOTEK: problem with my Neotek Elan II
To: [email protected]
Date: Tuesday, January 6, 2009, 3:34 PM
Ok, that could potentially be IC # U-4 on the master
module.
It's an NE-5532 dual op-amp, 8 pin DIP package.
It's
socketed so you should be able to pry it out with a
little
screw driver and put the new one in. MAKE SURE you put
it in
the right way up (the dot or notch on the end should
face
the top of the module) That would be the master
module, BTW,
the chip should be right under the "Aux A"
master
pot. If you are not sure what you are doing, get help.
Also,
make sure that all eight pins of the IC go into the
socket
and don't bend under it or outside it. AND, be
advised
that it could be other components besides the chip,
like
R-14, R-15 (both 47r, 1/4 watt) or C-103, 47uf/25v
Bi-polar.
best,
Ike
Brian Simmons wrote:
Hi !
Thanks alot for your quick reply !
It seems to be the same for all the channels.
-Brian
--- On Tue, 1/6/09, Ike Zimbel
<[email protected]> wrote:
From: Ike Zimbel
<[email protected]>
Subject: Re: NEOTEK: problem with my Neotek
Elan
II
To: [email protected]
Date: Tuesday, January 6, 2009, 2:33 PM
Hi Brian,
Is this on a per channel basis, or right
across the
board? If it is individual channels, it is
probably a bad solder joint on
the pan pot. This is really common on the
Elite
and may also happen on
the Elan.
best,
Ike
Brian Simmons wrote:
I bought a Neotek Elan II about 3 years
ago
and have
run into a problem with my Aux A/B section.
When I
pan the
individual channel Aux A/B to the right I get
a
full sinal
out of "B" but if I pan to the left
, I
get a very
low level signal that sounds a bit distorted
out
of
"A". When I solo the master send
for
"A"
its the same low level distorted signal.
I have very little experience in
electronics
so any
help would be greatly appreciated.
thanks
-Brian
------
You can unsubscribe at anytime by sending
an
email to
mailto:[email protected] with
"unsubscribe
neotek" in the message body. If you have
any
difficulties, or questions --please send an
email
to
[email protected].
The Neotek list is lovingly hosted by
Catapult Web
Development. Remember that any message or
reply
sent to the
list will be automatically forwarded to all
subscribers.
Vive Le Neotek !
Thanks.
-- Ike Zimbel
Zimbel Audio Productions Ltd.
Toronto
416-720-0887
"Studio House Calls" - Repairs and
upgrades to
analog audio equipment including: Amek, Allen
& Heath,
Neve, Neotek, MCI, Soundcraft and more.
------
You can unsubscribe at anytime by sending an
email
to
mailto:[email protected] with
"unsubscribe
neotek" in the message body. If you have
any
difficulties, or questions --please send an
email
to
[email protected].
The Neotek list is lovingly hosted by
Catapult
Web
Development. Remember that any message or
reply
sent to the
list will be automatically forwarded to all
subscribers.
Vive Le Neotek !
Thanks.
------
You can unsubscribe at anytime by sending an
email to
mailto:[email protected] with "unsubscribe
neotek" in the message body. If you have any
difficulties, or questions --please send an email to
[email protected].
The Neotek list is lovingly hosted by Catapult
Web
Development. Remember that any message or reply sent
to the
list will be automatically forwarded to all
subscribers.
Vive Le Neotek !
Thanks.
-- Ike Zimbel
Zimbel Audio Productions Ltd.
Toronto
416-720-0887
"Studio House Calls" - Repairs and upgrades
to
analog audio equipment including: Amek, Allen &
Heath,
Neve, Neotek, MCI, Soundcraft and more.
------
You can unsubscribe at anytime by sending an email to
mailto:[email protected] with "unsubscribe
neotek" in the message body. If you have any
difficulties, or questions --please send an email to
[email protected].
The Neotek list is lovingly hosted by Catapult Web
Development. Remember that any message or reply sent
to the
list will be automatically forwarded to all
subscribers.
Vive Le Neotek !
Thanks.
------
You can unsubscribe at anytime by sending an email to
mailto:[email protected] with "unsubscribe
neotek" in the message body. If you have any
difficulties, or questions --please send an email to
[email protected].
The Neotek list is lovingly hosted by Catapult Web
Development. Remember that any message or reply sent to the
list will be automatically forwarded to all subscribers.
Vive Le Neotek !
Thanks.
