YOU have a lot of work ahead. First off, if the carbs were really clean you 
wouldn't be writing about this. On the plus side, you don't seem to be adverse 
to the labor required. Remove the carb assembly once again. Do not separate 
from the "runner" that keeps them together. Remove float bowls and jets. The 
slow speed jets are most likely blocked. Whatever rust migrated through the 
system will be everywhere. Slowly clean all passages and jets that fuel flows 
through. You'll need cleaning wires, pressurized carb cleaner and compressed 
air. The idle mixture adjustment screws are the ones that have the caps on 
them. They should be removed and blown out given the nature of your problem 
(rust injestion) It is possible to remove the caps but most often they will 
break off and leave you with an additional problem. I carefully grind the stop 
tabs off with a Dremel. Gaining access to the fuel circuit they control will 
allow you clean a vital area. When replacing
 the idle mix screws, gently bottom out and back off about one turn as a 
starting point. The tabs prevented adjustment that would result in a rich 
mixture and not comply with EPA. I recently posted the wire sizes required to 
clean the jets of a 650 (#37 & #115). In the case of a rust problem like yours, 
I route the fuel line to allow me to use an automotive fuel filter. Find a 
place for it. My choice of carb cleaner is Berkbile 2+2 (not sold everywhere 
due to hazard) When working on carbs follow the instructions of med school; 
First do no harm. I might add that you need to verify that the fuel flow from 
the tank is adequate. I open the vacuum with a syringe and blow back into the 
tank. Rust is among the worst nightmares to deal with. Repeated cleaning is not 
unknown. Always work on one carb at a time and do not switch slides. In fact I 
don't remove them unless I suspect a defective diagphram. Before installing 
carbs, support them in an upright position
 and supply with fuel from an external tank source. Better to see if you have a 
leak now and not remove again. Observe the spray from the accelerator pump and 
insure it works. Good luck.

--- On Sat, 12/13/08, Andrew <[email protected]> wrote:
From: Andrew <[email protected]>
Subject: [Nighthawk Lovers] Starting problems
To: "Nighthawk Motorcycle Lovers!" <[email protected]>
Date: Saturday, December 13, 2008, 6:17 PM

Hi I have an 83 Nighthawk and I am having a problem getting it
started.

Before I start describing the problem I thought I should mention that
it sat for 4 years without being run.
So when I got it, I took the tank to a local shop and had it acid
etched and coated.  I also took the carbs off, cleaned them out and
put it all back together.  It ran great for a week, then I let sit.
The next tiime I went to start it, I realized the petcock was clogged
and the shop missed a spot on the tank.  I took it back and had it
recoated.

I took the carbs back of, cleaned them real good and put a new fuel
filter on.  Now I just can't seem to get it started.

When I go to start it, I twist the throttle a couple of times, set the
choke and crank.  It fires for a second or two, then dies.  Never
staying running.  I can never give it any "throttle" to keep it
running.

A couple of things I was wondering:
1.  Should I be tightening the either the small jets or the needle
valves from the air diagphrams above hand tight with a screwdriver?
Or should I leave them a little loose?  I wasn't sure if I am cutting
off the fuel by tightening them.
2.  What are the small teardrop adjusting nobs under the carbs?  There
is one for each carb except the far left carb near the petcock.

Any help is greatly appreciated.

Andrew





      
--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google Groups 
"Nighthawk Motorcycle Lovers!" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/nighthawk_lovers?hl=en
-~----------~----~----~----~------~----~------~--~---

Reply via email to