Actually I'd like to know the secret to getting the carbs out of the intake
manifolds. I've actually been using a modified allen wrench to remove the
manifolds from the engine and leaving them attached to the carbs.

-Kyle

On Sun, Dec 14, 2008 at 12:04 PM, Andrew <[email protected]> wrote:

>
>
> Hi Dennis and Kyle, thanks for the help.  I am about to go out and try
> your suggestions.  The only part I have not gone through and blown/
> cleaned out are those low speed channels you talked about.  I didn't
> know you could (should) remove them.  I'm hoping I can do it without
> breaking them.  I have cleaned out those jets in the bowls at least 4
> times.  I used a couple of small pieces of copper wire that I
> stripped.  Must not have done a good enough job since it wasn't the
> correct size.
>
> Is there a recommended way to remove the carbs from the rubber
> mounting holes?   I use a 4 foot long pry bar to gently push them out
> and back in after I loosen the clamps.
>
> Maybe I'll take some pictures.  Thanks Again,
> Andrew
>
>
> On Dec 14, 1:14 am, Dennis Hammerl <[email protected]> wrote:
> > YOU have a lot of work ahead. First off, if the carbs were really clean
> you wouldn't be writing about this. On the plus side, you don't seem to be
> adverse to the labor required. Remove the carb assembly once again. Do not
> separate from the "runner" that keeps them together. Remove float bowls and
> jets. The slow speed jets are most likely blocked. Whatever rust migrated
> through the system will be everywhere. Slowly clean all passages and jets
> that fuel flows through. You'll need cleaning wires, pressurized carb
> cleaner and compressed air. The idle mixture adjustment screws are the ones
> that have the caps on them. They should be removed and blown out given the
> nature of your problem (rust injestion) It is possible to remove the caps
> but most often they will break off and leave you with an additional problem.
> I carefully grind the stop tabs off with a Dremel. Gaining access to the
> fuel circuit they control will allow you clean a vital area. When replacing
> >  the idle mix screws, gently bottom out and back off about one turn as a
> starting point. The tabs prevented adjustment that would result in a rich
> mixture and not comply with EPA. I recently posted the wire sizes required
> to clean the jets of a 650 (#37 & #115). In the case of a rust problem like
> yours, I route the fuel line to allow me to use an automotive fuel filter.
> Find a place for it. My choice of carb cleaner is Berkbile 2+2 (not sold
> everywhere due to hazard) When working on carbs follow the instructions of
> med school; First do no harm. I might add that you need to verify that the
> fuel flow from the tank is adequate. I open the vacuum with a syringe and
> blow back into the tank. Rust is among the worst nightmares to deal with.
> Repeated cleaning is not unknown. Always work on one carb at a time and do
> not switch slides. In fact I don't remove them unless I suspect a defective
> diagphram. Before installing carbs, support them in an upright position
> >  and supply with fuel from an external tank source. Better to see if you
> have a leak now and not remove again. Observe the spray from the accelerator
> pump and insure it works. Good luck.
> >
> > --- On Sat, 12/13/08, Andrew <[email protected]> wrote:
> > From: Andrew <[email protected]>
> > Subject: [Nighthawk Lovers] Starting problems
> > To: "Nighthawk Motorcycle Lovers!" <[email protected]>
> > Date: Saturday, December 13, 2008, 6:17 PM
> >
> > Hi I have an 83 Nighthawk and I am having a problem getting it
> > started.
> >
> > Before I start describing the problem I thought I should mention that
> > it sat for 4 years without being run.
> > So when I got it, I took the tank to a local shop and had it acid
> > etched and coated.  I also took the carbs off, cleaned them out and
> > put it all back together.  It ran great for a week, then I let sit.
> > The next tiime I went to start it, I realized the petcock was clogged
> > and the shop missed a spot on the tank.  I took it back and had it
> > recoated.
> >
> > I took the carbs back of, cleaned them real good and put a new fuel
> > filter on.  Now I just can't seem to get it started.
> >
> > When I go to start it, I twist the throttle a couple of times, set the
> > choke and crank.  It fires for a second or two, then dies.  Never
> > staying running.  I can never give it any "throttle" to keep it
> > running.
> >
> > A couple of things I was wondering:
> > 1.  Should I be tightening the either the small jets or the needle
> > valves from the air diagphrams above hand tight with a screwdriver?
> > Or should I leave them a little loose?  I wasn't sure if I am cutting
> > off the fuel by tightening them.
> > 2.  What are the small teardrop adjusting nobs under the carbs?  There
> > is one for each carb except the far left carb near the petcock.
> >
> > Any help is greatly appreciated.
> >
> > Andrew
>
> >
>

--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google Groups 
"Nighthawk Motorcycle Lovers!" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/nighthawk_lovers?hl=en
-~----------~----~----~----~------~----~------~--~---

Reply via email to