Hi Dennis and Kyle, thanks for the help.  I am about to go out and try
your suggestions.  The only part I have not gone through and blown/
cleaned out are those low speed channels you talked about.  I didn't
know you could (should) remove them.  I'm hoping I can do it without
breaking them.  I have cleaned out those jets in the bowls at least 4
times.  I used a couple of small pieces of copper wire that I
stripped.  Must not have done a good enough job since it wasn't the
correct size.

Is there a recommended way to remove the carbs from the rubber
mounting holes?   I use a 4 foot long pry bar to gently push them out
and back in after I loosen the clamps.

Maybe I'll take some pictures.  Thanks Again,
Andrew


On Dec 14, 1:14 am, Dennis Hammerl <[email protected]> wrote:
> YOU have a lot of work ahead. First off, if the carbs were really clean you 
> wouldn't be writing about this. On the plus side, you don't seem to be 
> adverse to the labor required. Remove the carb assembly once again. Do not 
> separate from the "runner" that keeps them together. Remove float bowls and 
> jets. The slow speed jets are most likely blocked. Whatever rust migrated 
> through the system will be everywhere. Slowly clean all passages and jets 
> that fuel flows through. You'll need cleaning wires, pressurized carb cleaner 
> and compressed air. The idle mixture adjustment screws are the ones that have 
> the caps on them. They should be removed and blown out given the nature of 
> your problem (rust injestion) It is possible to remove the caps but most 
> often they will break off and leave you with an additional problem. I 
> carefully grind the stop tabs off with a Dremel. Gaining access to the fuel 
> circuit they control will allow you clean a vital area. When replacing
>  the idle mix screws, gently bottom out and back off about one turn as a 
> starting point. The tabs prevented adjustment that would result in a rich 
> mixture and not comply with EPA. I recently posted the wire sizes required to 
> clean the jets of a 650 (#37 & #115). In the case of a rust problem like 
> yours, I route the fuel line to allow me to use an automotive fuel filter. 
> Find a place for it. My choice of carb cleaner is Berkbile 2+2 (not sold 
> everywhere due to hazard) When working on carbs follow the instructions of 
> med school; First do no harm. I might add that you need to verify that the 
> fuel flow from the tank is adequate. I open the vacuum with a syringe and 
> blow back into the tank. Rust is among the worst nightmares to deal with. 
> Repeated cleaning is not unknown. Always work on one carb at a time and do 
> not switch slides. In fact I don't remove them unless I suspect a defective 
> diagphram. Before installing carbs, support them in an upright position
>  and supply with fuel from an external tank source. Better to see if you have 
> a leak now and not remove again. Observe the spray from the accelerator pump 
> and insure it works. Good luck.
>
> --- On Sat, 12/13/08, Andrew <[email protected]> wrote:
> From: Andrew <[email protected]>
> Subject: [Nighthawk Lovers] Starting problems
> To: "Nighthawk Motorcycle Lovers!" <[email protected]>
> Date: Saturday, December 13, 2008, 6:17 PM
>
> Hi I have an 83 Nighthawk and I am having a problem getting it
> started.
>
> Before I start describing the problem I thought I should mention that
> it sat for 4 years without being run.
> So when I got it, I took the tank to a local shop and had it acid
> etched and coated.  I also took the carbs off, cleaned them out and
> put it all back together.  It ran great for a week, then I let sit.
> The next tiime I went to start it, I realized the petcock was clogged
> and the shop missed a spot on the tank.  I took it back and had it
> recoated.
>
> I took the carbs back of, cleaned them real good and put a new fuel
> filter on.  Now I just can't seem to get it started.
>
> When I go to start it, I twist the throttle a couple of times, set the
> choke and crank.  It fires for a second or two, then dies.  Never
> staying running.  I can never give it any "throttle" to keep it
> running.
>
> A couple of things I was wondering:
> 1.  Should I be tightening the either the small jets or the needle
> valves from the air diagphrams above hand tight with a screwdriver?
> Or should I leave them a little loose?  I wasn't sure if I am cutting
> off the fuel by tightening them.
> 2.  What are the small teardrop adjusting nobs under the carbs?  There
> is one for each carb except the far left carb near the petcock.
>
> Any help is greatly appreciated.
>
> Andrew

--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google Groups 
"Nighthawk Motorcycle Lovers!" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/nighthawk_lovers?hl=en
-~----------~----~----~----~------~----~------~--~---

Reply via email to