Yes, a no load will work with standard bulbs as well as led.... As far as a
replacemrnt goes i would replace mine with a no load even if i dident have leds
-----Original Message-----
Date: Sunday, June 13, 2010 9:58:59 am
To: [email protected]
From: "Joey Kelley" <[email protected]>
Subject: Re: [Nighthawk Lovers] turn signals not working
Thats where I was going with that as well- a No-Load flasher unit will
continue to flash no matter what load is on the circuit. If I were you
Graham - I'd swap the flasher unit for a no-load unit and see if that
makes a difference. I think you can use a No-load on any circuit - so
it wouldn't harm traditional bulbs either.
-Joey
On Sun, Jun 13, 2010 at 9:45 AM, [email protected]
<[email protected]> wrote:
> The main reason flashers units dont work is the bulbs dont draw enough amps
> (did u reace with a lower watt bulb or leds???) the test is fairly simple,
> hook up a large light (i used a sealed beam headlight) into the circuit... If
> this makes it flash u need to get a digital flasher unit (spicifily for led
> turnsignals)...
> -----Original Message-----
> Date: Sunday, June 13, 2010 9:24:11 am
> To: "Nighthawk Motorcycle Lovers!" <[email protected]>
> From: "Graham Rogers" <[email protected]>
> Subject: [Nighthawk Lovers] turn signals not working
>
> Here's one I'm fed up with working on. I have two bikes that have
> nonworking right turn signals. They both do the same thing. So I'll
> describe one. (The other is a kz1000).
> It's a 1982/83 Suzuki GS1100L. I replaced the turn signals with new
> after markets. The front originls were running lights with three
> wires, the replacements are just two wire. So with the signals
> hooked up - and I'm sure I have the wires connected correctly on the
> front ones, leaving the running lights wires open (unconnected). The
> turn signals stay on when activated. The left ones turn on when I
> push the switch to the left, and same for the right. I have changed
> the flasher unit and the relay unit - no difference. A new battery
> and correct charging voltage makes no difference. It seems to me
> there's not enough voltage getting to the flasher unit to make it
> work. One wire out of the flasher unit reads over 12 v, the other -
> way under (it's a three prong unit). I have checked all grounds,
> added one, no difference. Any suggestions? Graham
>
> --
> You received this message because you are subscribed to the Google Groups
> "Nighthawk Motorcycle Lovers!" group.
> To post to this group, send email to [email protected].
> To unsubscribe from this group, send email to
> [email protected].
> For more options, visit this group at
> http://groups.google.com/group/nighthawk_lovers?hl=en.
>
>
>
> --
> You received this message because you are subscribed to the Google Groups
> "Nighthawk Motorcycle Lovers!" group.
> To post to this group, send email to [email protected].
> To unsubscribe from this group, send email to
> [email protected].
> For more options, visit this group at
> http://groups.google.com/group/nighthawk_lovers?hl=en.
>
>
--
-Joey Kelley
Need Computer Technical support?
http://www.crossloop.com/JoeyKelleyComputerServices
At your service - via remote control!
--
You received this message
--
You received this message because you are subscribed to the Google Groups
"Nighthawk Motorcycle Lovers!" group.
To post to this group, send email to [email protected].
To unsubscribe from this group, send email to
[email protected].
For more options, visit this group at
http://groups.google.com/group/nighthawk_lovers?hl=en.
