Well, with etherpeek I can only see information packet by packet, and nothing shows up on the nodes or protocols tab... any help on how to use all the data I have already captured to give me a list of all the IP addresses?
With Languard, it requires me to specify witch IP's to scan, but I don't know that!! Am I messing up somewhere? Filipe Joel de Almeida Network Consultant [EMAIL PROTECTED] Mobile: +351 967819600 -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of John Allhiser Sent: segunda-feira, 22 de Abril de 2002 20:41 To: NT 2000 Discussions Subject: RE: Network discovery Ahh. You can let the sniffer run for a while. This will let you know who is doing what on your network. For a simple list of addresses, try a simple scanner: http://www.gfi.com/lannetscan/index.htm This, of course depends on what hosts are running at the time. -----Original Message----- From: Filipe Joel de Almeida [mailto:[EMAIL PROTECTED]] Sent: Monday, April 22, 2002 2:42 PM To: NT 2000 Discussions Subject: RE: Network discovery I've installed the demo version, and it allows me to see packet by packet what's the source address and the destination address, but it seems there's no way of just getting a list of all the addresses. Filipe Joel de Almeida Network Consultant [EMAIL PROTECTED] Mobile: +351 967819600 -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of John Allhiser Sent: segunda-feira, 22 de Abril de 2002 19:13 To: NT 2000 Discussions Subject: RE: Network discovery Depending on the hardware you connect the sniffer to a mirrored or spanned port. the port effectively becomes a hub. -----Original Message----- From: Filipe Joel de Almeida [mailto:[EMAIL PROTECTED]] Sent: Monday, April 22, 2002 1:09 PM To: NT 2000 Discussions Subject: RE: Network discovery Thanks, I'll look it out. What If I was connected by switches, what could I do to do this? Filipe Joel de Almeida Network Consultant [EMAIL PROTECTED] Mobile: +351 967819600 -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of John Allhiser Sent: segunda-feira, 22 de Abril de 2002 18:52 To: NT 2000 Discussions Subject: RE: Network discovery Yes. Especially since you are connected by hubs. www.wildpackets.com -----Original Message----- From: Filipe Joel de Almeida [mailto:[EMAIL PROTECTED]] Sent: Monday, April 22, 2002 1:01 PM To: NT 2000 Discussions Subject: RE: Network discovery Is that software able to sniff my network and find all active IP addresses in any subnet? If so, where can I get it? Filipe Joel de Almeida Network Consultant [EMAIL PROTECTED] Mobile: +351 967819600 -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of John Allhiser Sent: segunda-feira, 22 de Abril de 2002 18:46 To: NT 2000 Discussions Subject: RE: Network discovery I use and like Wild Packets EtherPeek. -----Original Message----- From: Filipe Joel de Almeida [mailto:[EMAIL PROTECTED]] Sent: Monday, April 22, 2002 12:50 PM To: NT 2000 Discussions Subject: RE: Network discovery > If you network is as disastrous as it sounds, then you may not know what > IP ranges are being used. If that is the case maybe a TCP sniffer could > shed some light on what IPs are on the network. You are right! That is specifically what Is happening! Isn't there any good sniffer that could tell me what IP's are running around on my network? I can't seem to be able to make windump work! ------ You are subscribed as [email protected] Archives: http://www.swynk.com/sitesearch/search.asp To unsubscribe send a blank email to [EMAIL PROTECTED]
