On Wed, Oct 12, 2016 at 4:23 PM, Aashish Chaudhary < [email protected]> wrote:
> Can you try this: in nvidia control panel uncheck this option: "enable > stereoscopic 3D"? > Aashish, I was going to recommend this as well, but after I launched ParaView, I went back to see that this option had been re-enabled in the control panel. Something has apparently changed in the driver to make unchecking this option unnecessary. Cory > On Wed, Oct 12, 2016 at 4:00 PM Gao <[email protected]> wrote: > >> Hi Gory, >> >> You are right! I set to 120Hz and the 3D works! >> >> I didn't pay attention on the refresh rate because the 3D demo works, so >> I assumed the monitor is not the problem. It turned out that IS the >> problem. >> >> Also, I need to change the 120Hz on both the Quadro card and the monitor >> (both default to 60Hz). >> >> Now I am having a different issue: the display became blurry, although >> the 3D works. All the graphic elements are blurry except the 3D object. Not >> sure what cause this. >> >> I also noticed on the Windows 10, the monitor is recognized as "Generic >> PnP monitor" and use a MS driver. I searched and didn't find a driver for >> my Asus VG236H. >> >> Thank you very much. >> >> >> Gao >> >> >> >> On 2016-10-12 11:54 AM, Cory Quammen wrote: >> >> Gao, >> >> No, there isn't any setting needed in ParaView beyond the command-line >> arguments that you are already providing. >> >> One important thing, though: Make sure your screen refresh rate is set to >> 120 Hz or higher. >> >> - Cory >> >> >> >> On Wed, Oct 12, 2016 at 1:55 PM, Gao <[email protected]> wrote: >> >> Hi Cory, >> >> I just tried "Onboard DIN connector (with NVIDIA 3D ...)" and it's still >> not showing 3D stereo. >> >> My system is a Dell Precision workstation come with a Quadro 4000 video >> card (No DIN connection). The demo 3D test from Nvidia Control Panel works >> fine so I think the driver is loaded correctly. >> >> I just installed the new Paraview 5.2 RC1 and it does the same: No 3D but >> flickering. >> >> I also tried other modes and none of them works. >> >> Is there any special setting I need config in ParaView? >> >> Thanks for the help. >> >> Gao >> >> >> >> >> On 2016-10-12 08:51 AM, Cory Quammen wrote: >> >> Hi Gao, >> >> Attached is an image of the relevant NVIDIA Control Panel settings for >> our working ParaView stereo display setup. It looks like the main change >> from your setup is to change "Stereo - Display Mode" to "Onboard DIN >> connector (with NVIDIA 3D ...)". >> >> For your reference, our system runs Windows 10 and has a Quadro M5000 and >> an ASUS VG248QE 24-inch Full HD display. We did not need the optional 3-pin >> DIN connector port that seems almost impossible to buy anywhere. >> >> HTH, >> Cory >> >> On Tue, Oct 11, 2016 at 3:17 PM, Gao <[email protected]> wrote: >> >> Hi all, >> >> I am trying to make the stereo 3D working on Paraview but it doesn't >> work. I don't know what is the problem. >> >> I got NVIDIA 3D VISION 2 glasses and set it up on my Windows 10 PC. >> Installed the driver for the QUADRO 4000 card. Tested with the Nvidia >> Control Panel (version 8.1.1030.0) and the I can see the 3D demo through >> the glasses. >> >> Then I downloaded a sample vtk file from here: >> >> http://www.subdude-site.com/WebPages_Local/RefInfo/Computer/Linux/ >> LinuxGuidesByBlaze/apps3Dtools/3D_viewers-converters/3Dtestfiles/vtk/ >> rbc_001.vtk >> >> I changed some setting on Nvidia Control Panel: >> Manage 3D setting: >> Stereo - Display mode : Generic active stereo (with NVIDIA 3D Vision) >> Stereo -Enable: On >> Stereo -Swap eyes: Off >> >> Now I run paraview with： >> paraview.exe --stereo --stereo-type="Crystal Eyes" >> >> Then I open the vtk file I downloaded. I don't see 3D, and the image is >> flickering. But the emitter green light is ON. >> >> Can someone help me to get this 3D display going? >> >> Thanks. >> >> Gao >> >> >> _______________________________________________ >> Powered by www.kitware.com >> >> Visit other Kitware open-source projects at http://www.kitware.com/ >> opensource/opensource.html >> >> Please keep messages on-topic and check the ParaView Wiki at: >> http://paraview.org/Wiki/ParaView >> >> Search the list archives at: http://markmail.org/search/?q=ParaView >> >> Follow this link to subscribe/unsubscribe: >> http://public.kitware.com/mailman/listinfo/paraview >> >> >> >> >> -- >> Cory Quammen >> Staff R&D Engineer >> Kitware, Inc. >> >> >> >> >> >> -- >> Cory Quammen >> Staff R&D Engineer >> Kitware, Inc. >> >> >> _______________________________________________ >> Powered by www.kitware.com >> >> Visit other Kitware open-source projects at http://www.kitware.com/ >> opensource/opensource.html >> >> Please keep messages on-topic and check the ParaView Wiki at: >> http://paraview.org/Wiki/ParaView >> >> Search the list archives at: http://markmail.org/search/?q=ParaView >> >> Follow this link to subscribe/unsubscribe: >> http://public.kitware.com/mailman/listinfo/paraview >> > -- Cory Quammen Staff R&D Engineer Kitware, Inc.
_______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Search the list archives at: http://markmail.org/search/?q=ParaView Follow this link to subscribe/unsubscribe: http://public.kitware.com/mailman/listinfo/paraview
