I have looked at a pic of the TLDM, very similar but the top of the carb is not round. I will keep looking at pretty pics of carbs on the web, I am sure that I shall stumble across the right one eventually.... I hope.
Mark ________________________________ From: "[email protected]" <[email protected]> To: Quantum Owners Group <[email protected]> Sent: Sun, 24 October, 2010 10:03:27 Subject: [Quantum Owners] Re: mixture adjustment. Are the barrels square or round? Mine has a thumbwheel for adjusting the idle and that is a TLDM carb used on the later XR2s Russell On 24 Oct, 09:53, Mark Miles <[email protected]> wrote: > This seems to be the problem I am having with finding a diagram for the carb as > it is an '86 model cvh so I am guessing that the carb is probably an >aftermarket > unit or grafted on from a later engine. The carb has twin barrels and the idle > adjust screw is a thumbwheel type which is parallel to the ground. There is a > Weber tag attached to the carb but it has not aged well and is mostly > unreadable. I would have expected the mixture screw to be in the area you point > out but can see neither a screw nor anything resembling an appropriate orifice > to contain one. If all else fails then I shall have to remove the carb, find >the > screw then refit it to set it up which seems a disproportionate amount of work > for an engine that appears to be running well. > > Mark > > ________________________________ > From: "[email protected]" <[email protected]> > To: [email protected] > Sent: Sun, 24 October, 2010 0:46:45 > Subject: Re: [Quantum Owners] mixture adjustment. > > In a message dated 24/10/2010 00:00:26 GMT Daylight Time, [email protected] > writes: > I have a Weber carb on the car > If it is 1987 or later the mixture screw should be to the left and a little > below the idle speed screw. > The idle speed screw is mounted at an angle - head downwards and has a coil > spring acting as a locking device. the mixture screw may be concealed behind a > blocking plug so from the exterior it may just appear as a blanked off tube > moulded as part of the carb body. remove the plug to reveal the slotted screw > head. > > The Haynes manual also notes that when adjusting the idle speed screw the > electric fan should be kept running all the time. > > Michael-- > You received this message because you are subscribed to the Google Groups > "Quantum Owners Group" group. > To post to this group, send email to [email protected] > To unsubscribe from this group, send email to > [email protected] > For more options, visit this group >athttp://groups.google.com/group/quantumowners?hl=en > > IMPORTANT NOTE: All information presented herewith is provided on an "As Is" > basis, without warranty or the implication thereof. Neither the Quantum Owners > Club nor the individuals associated with the Quantum Owners Club or in the > preparation of the above information shall have any liability to any person or > entity with respect to liability, loss, or damage caused or alleged to be >caused > directly or indirectly by the instructions contained within this or related > message(s). -- You received this message because you are subscribed to the Google Groups "Quantum Owners Group" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/quantumowners?hl=en IMPORTANT NOTE: All information presented herewith is provided on an "As Is" basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor the individuals associated with the Quantum Owners Club or in the preparation of the above information shall have any liability to any person or entity with respect to liability, loss, or damage caused or alleged to be caused directly or indirectly by the instructions contained within this or related message(s). -- You received this message because you are subscribed to the Google Groups "Quantum Owners Group" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/quantumowners?hl=en IMPORTANT NOTE: All information presented herewith is provided on an "As Is" basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor the individuals associated with the Quantum Owners Club or in the preparation of the above information shall have any liability to any person or entity with respect to liability, loss, or damage caused or alleged to be caused directly or indirectly by the instructions contained within this or related message(s).
