> "if you don't ground the little wire provided at least at one end", One > grounds the shield/drain conductor ONLY at 1 end. > On Apr 17, 2020, at 3:00 PM, Jeff Clearwater <[email protected]> > wrote: > > Hey Kirk, > > yes shielded cable does little good if you don't ground the little wire > provided at least at one end. I just run a ground wire and tape it to the > CAT cable. > > Kirk Herander wrote on 4/17/20 5:50 AM: > >> So you terminate the shield somehow outside of the RJ45 connector? >>> On 4/16/2020 9:01:53 PM, Jeff Clearwater <[email protected]> >>> <mailto:[email protected]> wrote: >>> >>> When I did my cable swap and reconfiguration that fixed it I also was more >>> careful to route the xanbus cables away from the batter/inverter cables - >>> thinking that perhaps induction was the culprit. As I have an rj45 crimp >>> tool and some shielded CAT5e in the truck I think I'll just make up my own >>> cables in the future after spending way more time than that troubleshooting. >>> >>> Best of luck! >>> >>> jc >>> >>> Jason Szumlanski wrote on 4/16/20 3:00 PM: >>>> I tried swapping the cables for the XW and MPPT. After reboot the XW >>>> continued to show up on the SCP but the MPPT did not. I didn't have >>>> another cable, but this suggests the cable is not the problem. I didn't >>>> think to change the order, however. >>>> >>>> >>>> >>>> >>>> On Thu, Apr 16, 2020 at 5:57 PM Jeff Clearwater <[email protected] >>>> <mailto:[email protected]>> wrote: >>>> Hey Jason, >>>> >>>> I had a SCP xanbus system once that refused to show a component - The fix >>>> was replacing the cheap ethernet wires that schneider provided with better >>>> cables and/or changing the order of the components in the series comm >>>> string. not sure which did it as I did both changes at once but I do >>>> suspect those white cables. >>>> >>>> Best, >>>> >>>> Jeff >>>> >>>> Jason Szumlanski wrote on 4/16/20 1:03 PM: >>>>> I am working with a client (not my install) with a XW6048 and MPPT 80 600 >>>>> with a SCP. The SCP is not showing the MPPT in the setup menu. I am able >>>>> to access the system settings and XW configuration, but not the MPPT >>>>> settings. It is connected via Xanbus in this manner: >>>>> >>>>> SCP -> MPPT -> XW >>>>> >>>>> So the MPPT is in the middle and is passing through the XW signal just >>>>> fine. >>>>> >>>>> The MPPT also has a red error light illuminated, but it is charging the >>>>> battery (positive current measured via clamp meter). >>>>> >>>>> Any ideas? >>>>> >>>>> Thanks, >>>>> >>>>> Jason Szumlanski >>>>> >>>>> >>>>> >>>>> >>>>> _______________________________________________ >>>>> List sponsored by Redwood Alliance >>>>> >>>>> List Address: [email protected] >>>>> <mailto:[email protected]> >>>>> >>>>> Change listserver email address & settings: >>>>> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org >>>>> <https://mailtrack.io/trace/link/b90ca785a525b3990337afa8e4de7b8f58299dda?url=http%3A%2F%2Flists.re-wrenches.org%2Foptions.cgi%2Fre-wrenches-re-wrenches.org&userId=1613865&signature=a218969f1c881b8f> >>>>> >>>>> List-Archive: >>>>> http://www.mail-archive.com/[email protected]/maillist.html >>>>> >>>>> <https://mailtrack.io/trace/link/782ab5370a2dc90df34131154f96595de5604ebc?url=http%3A%2F%2Fwww.mail-archive.com%2Fre-wrenches%40lists.re-wrenches.org%2Fmaillist.html&userId=1613865&signature=6b59dfe40f1af8f5> >>>>> >>>>> List rules & etiquette: >>>>> www.re-wrenches.org/etiquette.htm >>>>> <https://mailtrack.io/trace/link/f342e1145ed8bd312cd51c8d9538e7d40534372f?url=http%3A%2F%2Fwww.re-wrenches.org%2Fetiquette.htm&userId=1613865&signature=aaed0000f561c13d> >>>>> >>>>> Check out or update participant bios: >>>>> www.members.re-wrenches.org >>>>> <https://mailtrack.io/trace/link/b3aac2fd00cbe275bdd68323bbd3326fd7073c2c?url=http%3A%2F%2Fwww.members.re-wrenches.org&userId=1613865&signature=b7fe990e7c6ebc5d> >>>>> >>>> >>>> -- >>>> ~~~~~~~~~~~ >>>> Jeff Clearwater >>>> VillageLab >>>> Village Power Design >>>> linkedin >>>> <https://mailtrack.io/trace/link/2b6554cfd6030cb29629ba73171aee87bce557b7?url=https%3A%2F%2Fwww.linkedin.com%2Fin%2Fjeff-clearwater-0622a312%2F&userId=1613865&signature=b502f02a345c328a> >>>> >>>> www.villagelab.net >>>> <https://mailtrack.io/trace/link/eaf54fba7350e494de8685771adb3c8b610c0ce2?url=http%3A%2F%2Fwww.villagelab.net&userId=1613865&signature=a7fed555763946d9> >>>> www.villagepowerdesign.com >>>> <https://mailtrack.io/trace/link/f35711ff79b27a2638bcbd392a1b2d9a09c7df5e?url=http%3A%2F%2Fwww.villagepowerdesign.com&userId=1613865&signature=aa4a4ddfbb35eb35> >>>> skype - jclearwater >>>> zoom by request >>>> cell - 413-559-9763 >>>> ~~~~~~~~~~~~~~~~~~~~~~~ >>>> >>>> >>>> >>>> _______________________________________________ >>>> List sponsored by Redwood Alliance >>>> >>>> List Address: [email protected] >>>> <mailto:[email protected]> >>>> >>>> Change listserver email address & settings: >>>> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org >>>> <http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org> >>>> >>>> List-Archive: >>>> http://www.mail-archive.com/[email protected]/maillist.html >>>> >>>> <http://www.mail-archive.com/[email protected]/maillist.html> >>>> >>>> List rules & etiquette: >>>> www.re-wrenches.org/etiquette.htm >>>> <http://www.re-wrenches.org/etiquette.htm> >>>> >>>> Check out or update participant bios: >>>> www.members.re-wrenches.org <http://www.members.re-wrenches.org/> >>>> >>> >>> -- >>> ~~~~~~~~~~~ >>> Jeff Clearwater >>> Village Power Design >>> linkedin <https://www.linkedin.com/in/jeff-clearwater-0622a312/> >>> www.villagepowerdesign.com <http://www.villagepowerdesign.com/> >>> cell - 413-559-9763 >>> ~~~~~~~~~~~~~~~~~~~~~~~ > > > -- > ~~~~~~~~~~~ > Jeff Clearwater > Village Power Design > linkedin <https://www.linkedin.com/in/jeff-clearwater-0622a312/> > www.villagepowerdesign.com <http://www.villagepowerdesign.com/> > cell - 413-559-9763 > ~~~~~~~~~~~~~~~~~~~~~~~ > _______________________________________________ > List sponsored by Redwood Alliance > > List Address: [email protected] > > Change listserver email address & settings: > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > List-Archive: > http://www.mail-archive.com/[email protected]/maillist.html > > List rules & etiquette: > www.re-wrenches.org/etiquette.htm > > Check out or update participant bios: > www.members.re-wrenches.org >
> [email protected] > <blocked::mailto:[email protected]%22%20%5Co%20%22blocked::mailto:[email protected]> > www.SWNL.net > <blocked::http://www.swnl.net/%22%20%5Co%20%22blocked::http://www.swnl.net/> > Solarwinds Northernlights > Serving Mid Coast Maine & Northern California > 207-832-7574 Cl. 610-517-8401 > > Blair "TUMP" May > ******** MAINE'S CHARTER ******** > NABCEP "Certified PV Installer" > > ******** MAINE'S CHARTER ******** > Trace Xantrex "Certified" Dealer / Installer" >
_______________________________________________ List sponsored by Redwood Alliance List Address: [email protected] Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://www.mail-archive.com/[email protected]/maillist.html List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out or update participant bios: www.members.re-wrenches.org
