[OSL | CCIE_Voice] sip call thru GK
hi exp, I config sip phone in (CME) Br-2, to call sccp phone in HQ (UCM). However ,when I called HQ phone 5001 (SCCP phone) from BR-2 phone 4001 (SIP phone). Call connected ,but when i pick up 5001, i was not able to talk, and after few second , it just disconnect. what I missed here ? tks in avd ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] CME-SRST dn-specific config
Hi, I am testing a scenario, where in I should be able to forward calls to voicemail while in SRST only for selected phones. I am using telephony-service, and srst mode auto-provision none. Currently for all the the phones Voicemail is working using below config. telephony-service sdspfarm units 5 sdspfarm tag 1 SC-CFB no privacy conference hardware srst mode auto-provision none srst ephone template 1 srst dn template 1 srst dn line-mode octo max-ephones 10 max-dn 10 ip source-address 192.102.66.254 port 2000 system message Your phones are in fallback max-conferences 8 gain -6 call-forward pattern .T transfer-system full-consult create cnf-files version-stamp 7960 Apr 05 2009 12:47:04 ! ! ephone-dn-template 1 call-forward busy 91658200 call-forward noan 91658200 timeout 20 ! ! ephone-template 1 privacy off privacy-button softkeys remote-in-use Newcall CBarge softkeys idle Newcall Redial softkeys seized Redial Endcall Cfwdall Pickup Gpickup Meetme softkeys connected Hold Endcall Trnsfer Park Confrn ConfList Warm Regards, Vinay Kumar ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] gatekeeper for CME
hi all, what is command we need in Gatekeeper , so in sh gatekeeper endpoint , the CME will show as VOIP-GW, rather than H.323 id ? tks ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] gatekeeper for CME
Are/How are your gateways registered to CUCM? On Mon, May 30, 2011 at 1:45 AM, donny f f.faraday...@gmail.com wrote: hi all, what is command we need in Gatekeeper , so in sh gatekeeper endpoint , the CME will show as VOIP-GW, rather than H.323 id ? tks ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] gatekeeper for CME
Remove the allow-connections commands. Thanks, Chevy On May 30, 2011 2:41 AM, donny f f.faraday...@gmail.com wrote: hi all, what is command we need in Gatekeeper , so in sh gatekeeper endpoint , the CME will show as VOIP-GW, rather than H.323 id ? tks ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CUE licensing question
Your bet won :) Rogers CCIE #28970 On May 25, 2011 4:44 AM, George Goglidze gogli...@gmail.com wrote: If you have to change it, my bet is they will provide the FTP server... Sent from my iPad On 24 May 2011, at 19:26, Cristobal Priego cristobalpri...@gmail.com wrote: hello all i was just curious if you need to change the cue license on the lab, if you don't have an ftp server to do so what are your options to get the proper license on the CUE ? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] sip call thru GK
Codec mismatch Sent from my iPhone On May 29, 2011, at 10:31 PM, donny f f.faraday...@gmail.com wrote: hi exp, I config sip phone in (CME) Br-2, to call sccp phone in HQ (UCM). However ,when I called HQ phone 5001 (SCCP phone) from BR-2 phone 4001 (SIP phone). Call connected ,but when i pick up 5001, i was not able to talk, and after few second , it just disconnect. what I missed here ? tks in avd ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] sip call thru GK
You may need to uncheck Wait for Far End H.245 Terminal Capability Set on the gateway. Warm Regards, Vinay Kumar From: Rrcrumm rrcr...@yahoo.com To: donny f f.faraday...@gmail.com Cc: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com Date: 05/30/2011 07:01 PM Subject: Re: [OSL | CCIE_Voice] sip call thru GK Codec mismatch Sent from my iPhone On May 29, 2011, at 10:31 PM, donny f f.faraday...@gmail.com wrote: hi exp, I config sip phone in (CME) Br-2, to call sccp phone in HQ (UCM). However ,when I called HQ phone 5001 (SCCP phone) from BR-2 phone 4001 (SIP phone). Call connected ,but when i pick up 5001, i was not able to talk, and after few second , it just disconnect. what I missed here ? tks in avd ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
I've noticed that if you reload BR1 router, it takes a long time for OSPF to populate the routes again. I've had to wait like 5-10 minutes before for the routes to get back on the router. That could possibly be what you're seeing. If that is the case, you should be able to ping the serial interfaces between HQ and BR1, but nothing else on HQ or BR2. Adam Compton On Sun, May 29, 2011 at 11:44 PM, Cristobal Priego cristobalpri...@gmail.com wrote: hello all while doing a mock lab i needed to configure LLQ, MLP LFI cRTP between BR1 and HQ, the bw was 384 when i issued auto qos voip trust fr-atm on both interfaces, after setting the BW on the inferfaces everything was great, no problem however once i reloaded the BR1 router i lost connectivity to the HQ site i reloaded HQ router and still no connectivity so i reverted my pod and resstarted again only with QOS i set the BW and ran the command again without any customization and the same issue happened, where i lost connectivity from BR1 to HQ do you guys know how to fix this ? thank you ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
Hi, Look at the forum history, I spoke about this issue and how to manage and resolve this issue a couple of week ago ;-) Claude Friderich PreSales Support CCIE Voice #29035 NETCORE PSF S.A. 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu mailto:cfrider...@netcore.lu From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of adam compton Sent: lundi 30 mai 2011 15:45 To: Cristobal Priego Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm I've noticed that if you reload BR1 router, it takes a long time for OSPF to populate the routes again. I've had to wait like 5-10 minutes before for the routes to get back on the router. That could possibly be what you're seeing. If that is the case, you should be able to ping the serial interfaces between HQ and BR1, but nothing else on HQ or BR2. Adam Compton On Sun, May 29, 2011 at 11:44 PM, Cristobal Priego cristobalpri...@gmail.com wrote: hello all while doing a mock lab i needed to configure LLQ, MLP LFI cRTP between BR1 and HQ, the bw was 384 when i issued auto qos voip trust fr-atm on both interfaces, after setting the BW on the inferfaces everything was great, no problem however once i reloaded the BR1 router i lost connectivity to the HQ site i reloaded HQ router and still no connectivity so i reverted my pod and resstarted again only with QOS i set the BW and ran the command again without any customization and the same issue happened, where i lost connectivity from BR1 to HQ do you guys know how to fix this ? thank you ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com http://www.ipexpert.com/ Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ image001.jpg___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Gatekeeper question
Hi, How do I get gk-trunk_1 and 2 to repflect port 1720? Thanks, Randall HQ-RTR(config)#do show gatekeeper gw GATEWAY TYPE PREFIX TABLE = Prefix: 3* Zone HQ master gateway list: 10.10.110.3:1720 BR2-RTR Prefix: 1#* Zone HQ master gateway list: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 1... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 5... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
I believe it was about the first week of May ;) On Mon, May 30, 2011 at 11:52 AM, Friderich Claude cfrider...@netcore.luwrote: Hi, Look at the forum history, I spoke about this issue and how to manage and resolve this issue a couple of week ago …. ;-) *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]*** *NETCORE PSF S.A.*** 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *adam compton *Sent:* lundi 30 mai 2011 15:45 *To:* Cristobal Priego *Cc:* ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm I've noticed that if you reload BR1 router, it takes a long time for OSPF to populate the routes again. I've had to wait like 5-10 minutes before for the routes to get back on the router. That could possibly be what you're seeing. If that is the case, you should be able to ping the serial interfaces between HQ and BR1, but nothing else on HQ or BR2. Adam Compton On Sun, May 29, 2011 at 11:44 PM, Cristobal Priego cristobalpri...@gmail.com wrote: hello all while doing a mock lab i needed to configure LLQ, MLP LFI cRTP between BR1 and HQ, the bw was 384 when i issued auto qos voip trust fr-atm on both interfaces, after setting the BW on the inferfaces everything was great, no problem however once i reloaded the BR1 router i lost connectivity to the HQ site i reloaded HQ router and still no connectivity so i reverted my pod and resstarted again only with QOS i set the BW and ran the command again without any customization and the same issue happened, where i lost connectivity from BR1 to HQ do you guys know how to fix this ? thank you ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com image001.jpg___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Gatekeeper question
In callmanager system -- service parameters' search on 1720 and and replace 'None' with 'gk-trunk' --- On Mon, 5/30/11, Randall Crumm rrcr...@yahoo.com wrote: From: Randall Crumm rrcr...@yahoo.com Subject: [OSL | CCIE_Voice] Gatekeeper question To: Online Study ccie_voice@onlinestudylist.com Date: Monday, May 30, 2011, 10:39 AM Hi, How do I get gk-trunk_1 and 2 to repflect port 1720? Thanks, Randall HQ-RTR(config)#do show gatekeeper gw GATEWAY TYPE PREFIX TABLE = Prefix: 3* Zone HQ master gateway list: 10.10.110.3:1720 BR2-RTR Prefix: 1#* Zone HQ master gateway list: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 1... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 5... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 -Inline Attachment Follows- ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Gatekeeper question
Go to service parameters, choose call manager and search for trunk and will find the option to make the gatekeeper h225 trunk to use 1720, and then put the name of your h225 trunk which is GK-TRUNK From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Randall Crumm Sent: Monday, May 30, 2011 9:39 PM To: Online Study Subject: [OSL | CCIE_Voice] Gatekeeper question Hi, How do I get gk-trunk_1 and 2 to repflect port 1720? Thanks, Randall HQ-RTR(config)#do show gatekeeper gw GATEWAY TYPE PREFIX TABLE = Prefix: 3* Zone HQ master gateway list: 10.10.110.3:1720 BR2-RTR Prefix: 1#* Zone HQ master gateway list: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 1... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 5... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 * * This Communication is Private Confidential. This message and any attachments may contain information that is privileged and / or confidential and is the property of MHD InfoTech LLC. * * It is intended solely for the person to whom it is addressed. If you are not the intended recipient, you are hereby notified that you are not authorized to read, print, retain copy, disseminate, distribute, or * * use this message any attachments or any part thereof. If you have received this message in error, please notify the sender immediately and delete the message and any attachments from your system. * * ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Gatekeeper question
go to service parameters in Publisher, select your Pub, then call manager active, search for 1720 and you will find it. There you put the name of your gatekeeper controlled trunk. In your case it looks like you got it named gk-trunk so use that or any other name you made your trunk. On Mon, May 30, 2011 at 12:39 PM, Randall Crumm rrcr...@yahoo.com wrote: Hi, How do I get gk-trunk_1 and 2 to repflect port 1720? Thanks, Randall HQ-RTR(config)#do show gatekeeper gw GATEWAY TYPE PREFIX TABLE = Prefix: 3* Zone HQ master gateway list: 10.10.110.3:1720 BR2-RTR Prefix: 1#* Zone HQ master gateway list: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 1... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 5... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Gatekeeper question
CCM service Device Name of GK-controlled Trunk That Will Use Port 1720; just type the trunk name. Rgs, Roger Carpio. On Mon, May 30, 2011 at 11:39 AM, Randall Crumm rrcr...@yahoo.com wrote: Hi, How do I get gk-trunk_1 and 2 to repflect port 1720? Thanks, Randall HQ-RTR(config)#do show gatekeeper gw GATEWAY TYPE PREFIX TABLE = Prefix: 3* Zone HQ master gateway list: 10.10.110.3:1720 BR2-RTR Prefix: 1#* Zone HQ master gateway list: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 1... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 5... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Gatekeeper question
CCM service parameter under h323 section -Original Message- From: Randall Crumm rrcr...@yahoo.com Sender: ccie_voice-boun...@onlinestudylist.com Date: Mon, 30 May 2011 10:39:19 To: Online Studyccie_voice@onlinestudylist.com Reply-To: Randall Crumm rrcr...@yahoo.com Subject: [OSL | CCIE_Voice] Gatekeeper question ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Gatekeeper question
Randall, Add the name of the GK-controlled trunk on the service parameter named Device Name of GK-controlled Trunk That Will Use Port 1720, then restart the Trunk. -Pablo Meneses. On Mon, May 30, 2011 at 11:39 AM, Randall Crumm rrcr...@yahoo.com wrote: Hi, How do I get gk-trunk_1 and 2 to repflect port 1720? Thanks, Randall HQ-RTR(config)#do show gatekeeper gw GATEWAY TYPE PREFIX TABLE = Prefix: 3* Zone HQ master gateway list: 10.10.110.3:1720 BR2-RTR Prefix: 1#* Zone HQ master gateway list: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 1... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 5... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Gatekeeper question--RC
Thanks for all the answers. I did search the services for 1720 and entered gk-trunk. I'm working on WB2 lab 2 and the output from the PG shows port 1720 and my output shows 40081 and 33277 respectively below. The questions in the WB has output and says the port should show 1720 no 40081 and 33277. This is what I am trying to do. The PG did not specify anything specific as well. Should I not worry about this? Randall From: Roger Carpio roger.car...@gmail.com To: Randall Crumm rrcr...@yahoo.com Cc: Online Study ccie_voice@onlinestudylist.com Sent: Monday, May 30, 2011 12:07 PM Subject: Re: [OSL | CCIE_Voice] Gatekeeper question CCM service Device Name of GK-controlled Trunk That Will Use Port 1720; just type the trunk name. Rgs, Roger Carpio. On Mon, May 30, 2011 at 11:39 AM, Randall Crumm rrcr...@yahoo.com wrote: Hi, How do I get gk-trunk_1 and 2 to repflect port 1720? Thanks, Randall HQ-RTR(config)#do show gatekeeper gw GATEWAY TYPE PREFIX TABLE = Prefix: 3* Zone HQ master gateway list: 10.10.110.3:1720 BR2-RTR Prefix: 1#* Zone HQ master gateway list: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 1... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 5... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] CUE/CME
HI, Here is a dumb question, but causing me issues. My cue is stable and I can log in to the web page with the user from the cue cli. Now when I start the initialization wizard I keep getting login to CME as administrator failed. check CME config. Am I suppose to use the user under tele-service? In my case admin/c1sc0123? snip-its ip http server ip http authentication local no ip http secure-server ip http path flash:/GUI telephony-service max-ephones 7 max-dn 7 ip source-address 10.10.110.3 port 2000 voicemail 3600 max-conferences 8 gain -6 call-forward pattern .T web admin system name admin password c1sc0123 dn-webedit transfer-system full-consult transfer-pattern . transfer-pattern .T ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Gatekeeper question--RC
That should do it. If they do not show the requested port after adding the trunk name to the service parameter I would try resetting the trunk; resetting CCM service, gatekeeper shut/no shut etc. Rgs, Roger Carpio. On Mon, May 30, 2011 at 1:36 PM, Randall Crumm rrcr...@yahoo.com wrote: Thanks for all the answers. I did search the services for 1720 and entered gk-trunk. I'm working on WB2 lab 2 and the output from the PG shows port 1720 and my output shows 40081 and 33277 respectively below. The questions in the WB has output and says the port should show 1720 no 40081 and 33277. This is what I am trying to do. The PG did not specify anything specific as well. Should I not worry about this? Randall -- *From:* Roger Carpio roger.car...@gmail.com *To:* Randall Crumm rrcr...@yahoo.com *Cc:* Online Study ccie_voice@onlinestudylist.com *Sent:* Monday, May 30, 2011 12:07 PM *Subject:* Re: [OSL | CCIE_Voice] Gatekeeper question CCM service Device Name of GK-controlled Trunk That Will Use Port 1720; just type the trunk name. Rgs, Roger Carpio. On Mon, May 30, 2011 at 11:39 AM, Randall Crumm rrcr...@yahoo.com wrote: Hi, How do I get gk-trunk_1 and 2 to repflect port 1720? Thanks, Randall HQ-RTR(config)#do show gatekeeper gw GATEWAY TYPE PREFIX TABLE = Prefix: 3* Zone HQ master gateway list: 10.10.110.3:1720 BR2-RTR Prefix: 1#* Zone HQ master gateway list: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 1... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 5... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
do you recall the subject ? I can't find it i found some qos discussions, however it was related to LAN qos thank you 2011/5/30 Bill Lake whl...@gmail.com I believe it was about the first week of May ;) On Mon, May 30, 2011 at 11:52 AM, Friderich Claude cfrider...@netcore.luwrote: Hi, Look at the forum history, I spoke about this issue and how to manage and resolve this issue a couple of week ago …. ;-) *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]*** *NETCORE PSF S.A.*** 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *adam compton *Sent:* lundi 30 mai 2011 15:45 *To:* Cristobal Priego *Cc:* ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm I've noticed that if you reload BR1 router, it takes a long time for OSPF to populate the routes again. I've had to wait like 5-10 minutes before for the routes to get back on the router. That could possibly be what you're seeing. If that is the case, you should be able to ping the serial interfaces between HQ and BR1, but nothing else on HQ or BR2. Adam Compton On Sun, May 29, 2011 at 11:44 PM, Cristobal Priego cristobalpri...@gmail.com wrote: hello all while doing a mock lab i needed to configure LLQ, MLP LFI cRTP between BR1 and HQ, the bw was 384 when i issued auto qos voip trust fr-atm on both interfaces, after setting the BW on the inferfaces everything was great, no problem however once i reloaded the BR1 router i lost connectivity to the HQ site i reloaded HQ router and still no connectivity so i reverted my pod and resstarted again only with QOS i set the BW and ran the command again without any customization and the same issue happened, where i lost connectivity from BR1 to HQ do you guys know how to fix this ? thank you ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com image001.jpg___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Gatekeeper question--RC
Hi Roger, I thought of restarting the cm service, that didn't work. I reset the trunk (did not work), then shut/no shut the GK and it worked. THANKS!!! Randall From: Roger Carpio roger.car...@gmail.com To: Randall Crumm rrcr...@yahoo.com Cc: Online Study ccie_voice@onlinestudylist.com Sent: Monday, May 30, 2011 1:08 PM Subject: Re: [OSL | CCIE_Voice] Gatekeeper question--RC That should do it. If they do not show the requested port after adding the trunk name to the service parameter I would try resetting the trunk; resetting CCM service, gatekeeper shut/no shut etc. Rgs, Roger Carpio. On Mon, May 30, 2011 at 1:36 PM, Randall Crumm rrcr...@yahoo.com wrote: Thanks for all the answers. I did search the services for 1720 and entered gk-trunk. I'm working on WB2 lab 2 and the output from the PG shows port 1720 and my output shows 40081 and 33277 respectively below. The questions in the WB has output and says the port should show 1720 no 40081 and 33277. This is what I am trying to do. The PG did not specify anything specific as well. Should I not worry about this? Randall From: Roger Carpio roger.car...@gmail.com To: Randall Crumm rrcr...@yahoo.com Cc: Online Study ccie_voice@onlinestudylist.com Sent: Monday, May 30, 2011 12:07 PM Subject: Re: [OSL | CCIE_Voice] Gatekeeper question CCM service Device Name of GK-controlled Trunk That Will Use Port 1720; just type the trunk name. Rgs, Roger Carpio. On Mon, May 30, 2011 at 11:39 AM, Randall Crumm rrcr...@yahoo.com wrote: Hi, How do I get gk-trunk_1 and 2 to repflect port 1720? Thanks, Randall HQ-RTR(config)#do show gatekeeper gw GATEWAY TYPE PREFIX TABLE = Prefix: 3* Zone HQ master gateway list: 10.10.110.3:1720 BR2-RTR Prefix: 1#* Zone HQ master gateway list: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 1... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 5... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
I found it just in case somebody else is interested this is exactly what happened to me and indeed Friderich described quite well i'm going to copy paste the issue and the solution that he found As I configure qos with MLP LFI between hq and br2 everything was working fine !!! After rebooting, no serial access anymore between hq and br2….. With *show ip interface brief* I have the following protocol state : *HQ* Interface IP-AddressOK? Method StatusProtocol Virtual-Access1 *10.10.112.1*YES TFTP up down *BR2* Interface IP-AddressOK? Method StatusProtocol Virtual-Access1* 10.10.112.2*YES TFTP up down onclusion: On HQ, Just have to put the command line no frame-relay interface-dlci 202 ppp Virtual-Template100 and shut the Serial interface 0/1/0 and put the command frame-relay interface-dlci 202 ppp Virtual-Template100 and no shut to make it work again Hope this can help you during the real lab … Think it’s the easiest solution to make it work …. Have to keep this in mind J And again, thanks to all for your remarks and suggestions i'm going to give this a try in 15 mins i just need to have all the infrastructure stuff fixed 2011/5/30 Cristobal Priego cristobalpri...@gmail.com do you recall the subject ? I can't find it i found some qos discussions, however it was related to LAN qos thank you 2011/5/30 Bill Lake whl...@gmail.com I believe it was about the first week of May ;) On Mon, May 30, 2011 at 11:52 AM, Friderich Claude cfrider...@netcore.lu wrote: Hi, Look at the forum history, I spoke about this issue and how to manage and resolve this issue a couple of week ago …. ;-) *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]*** *NETCORE PSF S.A.*** 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *adam compton *Sent:* lundi 30 mai 2011 15:45 *To:* Cristobal Priego *Cc:* ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm I've noticed that if you reload BR1 router, it takes a long time for OSPF to populate the routes again. I've had to wait like 5-10 minutes before for the routes to get back on the router. That could possibly be what you're seeing. If that is the case, you should be able to ping the serial interfaces between HQ and BR1, but nothing else on HQ or BR2. Adam Compton On Sun, May 29, 2011 at 11:44 PM, Cristobal Priego cristobalpri...@gmail.com wrote: hello all while doing a mock lab i needed to configure LLQ, MLP LFI cRTP between BR1 and HQ, the bw was 384 when i issued auto qos voip trust fr-atm on both interfaces, after setting the BW on the inferfaces everything was great, no problem however once i reloaded the BR1 router i lost connectivity to the HQ site i reloaded HQ router and still no connectivity so i reverted my pod and resstarted again only with QOS i set the BW and ran the command again without any customization and the same issue happened, where i lost connectivity from BR1 to HQ do you guys know how to fix this ? thank you ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com image001.jpg___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] DTMF problem
Hello I have a doubt, when is configured CUBE and this have xcode configured and also other xcode registered to CCM, how I can to know the xcode of where this being used? Thanks. La informaci?n incluida en este mensaje y sus anexos es CONFIDENCIAL y para USO EXCLUSIVO de sus destinatarios. No est? permitida su divulgaci?n y/o reproducci?n sin autorizaci?n. Si ha recibido este mensaje y no le incumbe, le rogamos nos los comunique y proceda a su borrado. Gracias. Information included in this e-mail and attached files is CONFIDENTIAL and only for the EXCLUSIVE USE of the receivers. Circulation and/or copy without permission is not allowed. If you have received this e-mail and you are not the intended recipient, please let us know and erase the message and attached files. Thank you. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
For MLP LFI, if you create the virtual-template manually (no auto-qos), it's going to work. If not, just got to frame-relay interface-dlci 102 ppp Virtual-Template200 and put no frame-relay interface-dlci 102 ppp Virtual-Template200 Shut the serial interface. Put frame-relay interface-dlci 102 ppp Virtual-Template200 again and no shut the Serial Interface. Do this manipulation on the 2 sites configured with MLP. But for the Lab, normally you just have to reload the routers to make it work. Check with show policy-map interface to make sure that the policy-map is good configured and that you have traffic for sig and RTP Regards, Claude Friderich PreSales Support CCIE Voice #29035 NETCORE PSF S.A. 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu mailto:cfrider...@netcore.lu From: Cristobal Priego [mailto:cristobalpri...@gmail.com] Sent: lundi 30 mai 2011 22:13 To: Bill Lake Cc: Friderich Claude; adam compton; ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm do you recall the subject ? I can't find it i found some qos discussions, however it was related to LAN qos thank you 2011/5/30 Bill Lake whl...@gmail.com I believe it was about the first week of May ;) On Mon, May 30, 2011 at 11:52 AM, Friderich Claude cfrider...@netcore.lu wrote: Hi, Look at the forum history, I spoke about this issue and how to manage and resolve this issue a couple of week ago ;-) Claude Friderich PreSales Support CCIE Voice #29035 NETCORE PSF S.A. 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 tel:%2B352%2031%2033%2080%20407 Fax: +352 31 33 80 412 tel:%2B352%2031%2033%2080%20412 GSM: +352 621 303 616 tel:%2B352%20621%20303%20616 E-mail: cfrider...@netcore.lu mailto:cfrider...@netcore.lu From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of adam compton Sent: lundi 30 mai 2011 15:45 To: Cristobal Priego Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm I've noticed that if you reload BR1 router, it takes a long time for OSPF to populate the routes again. I've had to wait like 5-10 minutes before for the routes to get back on the router. That could possibly be what you're seeing. If that is the case, you should be able to ping the serial interfaces between HQ and BR1, but nothing else on HQ or BR2. Adam Compton On Sun, May 29, 2011 at 11:44 PM, Cristobal Priego cristobalpri...@gmail.com wrote: hello all while doing a mock lab i needed to configure LLQ, MLP LFI cRTP between BR1 and HQ, the bw was 384 when i issued auto qos voip trust fr-atm on both interfaces, after setting the BW on the inferfaces everything was great, no problem however once i reloaded the BR1 router i lost connectivity to the HQ site i reloaded HQ router and still no connectivity so i reverted my pod and resstarted again only with QOS i set the BW and ran the command again without any customization and the same issue happened, where i lost connectivity from BR1 to HQ do you guys know how to fix this ? thank you ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com http://www.ipexpert.com/ Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com image004.jpgimage003.jpg___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] IPPM on cisco7961 didn't alert
Hey, Do you still remember how did you resolve this alert issue? I'm still trying to train myself up in CUPS. Last night, my alert was working, my IPPM login wasn't. Today my IPPM is working but no alert. =( All other components are working. On Sun, Dec 26, 2010 at 12:59 AM, ShinGei Yong shingei.y...@gmail.comwrote: Guys, Pls ignore this mail, has managed to figured out the caused. thanks Shingei. On Sat, Dec 25, 2010 at 4:36 PM, ShinGei Yong shingei.y...@gmail.comwrote: Hi, I've configure the IPPM on cisco 7961 phone, everything works smooth other that the message receive alert. It doesn't ring when there is a mgs come in from CIPC or other IPPM.i've set the audible alert to ON but still got no luck. Another IPPM phone encounter the same issue, so don't think is the phone problem. Any idea? Thanks Shingei. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
I just tried it and this is what happens I reloaded the router and i don't have connectivity to BR1 now, so i started on the HQ router this is how my interface looks before i make the change interface Serial0/0/1:0.1 point-to-point bandwidth 384 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 201 ppp Virtual-Template200 class AutoQoS-FR-Se0/0/1:0-201 auto qos voip trust fr-atm R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#interface Serial0/0/1:0.1 point-to-point R1(config-subif)#sh R1(config-subif)#no frame-relay interface-dlci 201 ppp Virtual-Template200 as soon as I enter that command I get the Errors below: no frame-relay interface-dlci 201 ppp Virtual-Template200 ^ % Invalid input detected at '^' marker. AutoQoS Error: the following command could not be parsed: no frame-relay interface-dlci 201 ppp Virtual-Template200 R1(config-subif)# *May 31 01:51:19.535: %LINK-5-CHANGED: Interface Virtual-Template200, changed state to administratively down R1(config-subif)# When I try to re-enter the Command on the sub interface this is what i get: R1(config-subif)#frame-relay interface-dlci 201 ppp Virtual-Template200 %vtemplate error; failed to set up PPP-FR circuit R1(config-subif)# and my interface looks like this : ! interface Serial0/0/1:0.1 point-to-point bandwidth 384 ip address 10.10.111.1 255.255.255.0 ip ospf mtu-ignore shutdown snmp trap link-status end 2011/5/30 Friderich Claude cfrider...@netcore.lu For MLP LFI, if you create the virtual-template manually (no auto-qos), it’s going to work. If not, just got to “frame-relay interface-dlci 102 ppp Virtual-Template200” and put no frame-relay interface-dlci 102 ppp Virtual-Template200 Shut the serial interface. Put frame-relay interface-dlci 102 ppp Virtual-Template200 again and no shut the Serial Interface. Do this manipulation on the 2 sites configured with MLP. But for the Lab, normally you just have to reload the routers to make it work. Check with show policy-map interface to make sure that the policy-map is good configured and that you have traffic for sig and RTP Regards, *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]*** *NETCORE PSF S.A.*** 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* Cristobal Priego [mailto:cristobalpri...@gmail.com] *Sent:* lundi 30 mai 2011 22:13 *To:* Bill Lake *Cc:* Friderich Claude; adam compton; ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm do you recall the subject ? I can't find it i found some qos discussions, however it was related to LAN qos thank you 2011/5/30 Bill Lake whl...@gmail.com I believe it was about the first week of May ;) On Mon, May 30, 2011 at 11:52 AM, Friderich Claude cfrider...@netcore.lu wrote: Hi, Look at the forum history, I spoke about this issue and how to manage and resolve this issue a couple of week ago …. ;-) *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]* *NETCORE PSF S.A.* 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *adam compton *Sent:* lundi 30 mai 2011 15:45 *To:* Cristobal Priego *Cc:* ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm I've noticed that if you reload BR1 router, it takes a long time for OSPF to populate the routes again. I've had to wait like 5-10 minutes before for the routes to get back on the router. That could possibly be what you're seeing. If that is the case, you should be able to ping the serial interfaces between HQ and BR1, but nothing else on HQ or BR2. Adam Compton On Sun, May 29, 2011 at 11:44 PM, Cristobal Priego cristobalpri...@gmail.com wrote: hello all while doing a mock lab i needed to configure LLQ, MLP LFI cRTP between BR1 and HQ, the bw was 384 when i issued auto qos voip trust fr-atm on both interfaces, after setting the BW on the inferfaces everything was great, no problem however once i reloaded the BR1 router i lost connectivity to the HQ site i reloaded HQ router and still no connectivity so i reverted my pod and resstarted again only with QOS i set the BW and ran the command again without any customization and the same issue happened, where i lost connectivity from BR1 to HQ do you guys know how to fix this ? thank you ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a
Re: [OSL | CCIE_Voice] Gatekeeper question--RC
did you reset the Trunk after you made the change on Service Parameters ? If you have a GK on the lab and if it's telling you to use 1720 and your output doesn't show port 1720 2011/5/30 Randall Crumm rrcr...@yahoo.com Thanks for all the answers. I did search the services for 1720 and entered gk-trunk. I'm working on WB2 lab 2 and the output from the PG shows port 1720 and my output shows 40081 and 33277 respectively below. The questions in the WB has output and says the port should show 1720 no 40081 and 33277. This is what I am trying to do. The PG did not specify anything specific as well. Should I not worry about this? Randall -- *From:* Roger Carpio roger.car...@gmail.com *To:* Randall Crumm rrcr...@yahoo.com *Cc:* Online Study ccie_voice@onlinestudylist.com *Sent:* Monday, May 30, 2011 12:07 PM *Subject:* Re: [OSL | CCIE_Voice] Gatekeeper question CCM service Device Name of GK-controlled Trunk That Will Use Port 1720; just type the trunk name. Rgs, Roger Carpio. On Mon, May 30, 2011 at 11:39 AM, Randall Crumm rrcr...@yahoo.com wrote: Hi, How do I get gk-trunk_1 and 2 to repflect port 1720? Thanks, Randall HQ-RTR(config)#do show gatekeeper gw GATEWAY TYPE PREFIX TABLE = Prefix: 3* Zone HQ master gateway list: 10.10.110.3:1720 BR2-RTR Prefix: 1#* Zone HQ master gateway list: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 1... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 Zone HQ prefix 5... priority gateway list(s): Priority 5: 10.10.210.10:40081 GK-TRUNK_1 10.10.210.11:33277 GK-TRUNK_2 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CUE/CME
no when you do the initial setup for CUE it indeed request a user id/password, the last step on the setup those are the credentials that you should use the user/name password set under telephony-service that's indeed user for the integration 2011/5/30 Randall Crumm rrcr...@yahoo.com HI, Here is a dumb question, but causing me issues. My cue is stable and I can log in to the web page with the user from the cue cli. Now when I start the initialization wizard I keep getting login to CME as administrator failed. check CME config. Am I suppose to use the user under tele-service? In my case admin/c1sc0123? snip-its ip http server ip http authentication local no ip http secure-server ip http path flash:/GUI telephony-service max-ephones 7 max-dn 7 ip source-address 10.10.110.3 port 2000 voicemail 3600 max-conferences 8 gain -6 call-forward pattern .T web admin system name admin password c1sc0123 dn-webedit transfer-system full-consult transfer-pattern . transfer-pattern .T ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CUE/CME
Look at the folder's name in flash memory where GUI files are stored. It must match what you defined under ip http path flash:/GUI and btw is case sensitive :-P Rgs, Roger Carpio. On Mon, May 30, 2011 at 2:08 PM, Randall Crumm rrcr...@yahoo.com wrote: HI, Here is a dumb question, but causing me issues. My cue is stable and I can log in to the web page with the user from the cue cli. Now when I start the initialization wizard I keep getting login to CME as administrator failed. check CME config. Am I suppose to use the user under tele-service? In my case admin/c1sc0123? snip-its ip http server ip http authentication local no ip http secure-server ip http path flash:/GUI telephony-service max-ephones 7 max-dn 7 ip source-address 10.10.110.3 port 2000 voicemail 3600 max-conferences 8 gain -6 call-forward pattern .T web admin system name admin password c1sc0123 dn-webedit transfer-system full-consult transfer-pattern . transfer-pattern .T ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
http://www.mail-archive.com/ccie_voice@onlinestudylist.com/msg21425.html On Mon, May 30, 2011 at 22:13, Cristobal Priego cristobalpri...@gmail.comwrote: do you recall the subject ? I can't find it i found some qos discussions, however it was related to LAN qos thank you 2011/5/30 Bill Lake whl...@gmail.com I believe it was about the first week of May ;) On Mon, May 30, 2011 at 11:52 AM, Friderich Claude cfrider...@netcore.lu wrote: Hi, Look at the forum history, I spoke about this issue and how to manage and resolve this issue a couple of week ago …. ;-) *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]*** *NETCORE PSF S.A.*** 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *adam compton *Sent:* lundi 30 mai 2011 15:45 *To:* Cristobal Priego *Cc:* ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm I've noticed that if you reload BR1 router, it takes a long time for OSPF to populate the routes again. I've had to wait like 5-10 minutes before for the routes to get back on the router. That could possibly be what you're seeing. If that is the case, you should be able to ping the serial interfaces between HQ and BR1, but nothing else on HQ or BR2. Adam Compton On Sun, May 29, 2011 at 11:44 PM, Cristobal Priego cristobalpri...@gmail.com wrote: hello all while doing a mock lab i needed to configure LLQ, MLP LFI cRTP between BR1 and HQ, the bw was 384 when i issued auto qos voip trust fr-atm on both interfaces, after setting the BW on the inferfaces everything was great, no problem however once i reloaded the BR1 router i lost connectivity to the HQ site i reloaded HQ router and still no connectivity so i reverted my pod and resstarted again only with QOS i set the BW and ran the command again without any customization and the same issue happened, where i lost connectivity from BR1 to HQ do you guys know how to fix this ? thank you ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com image001.jpg___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
thanks i indeed found the Thread i finally got it working what's happening in my case is when i go to the sub interface and remove the line frame-relay interface-dlci 201 ppp Virtual-Template200 the virtual-tempate is gone so i need to recreate the template first interface Virtual-Template200 bandwidth 384 ip address 10.10.111.1 255.255.255.0 ppp multilink ppp multilink interleave ppp multilink fragment delay 10 service-policy output AutoQoS-Policy-Trust end then go back to the sub interface re-issue the command frame-relay interface-dlci 201 ppp Virtual-Template200 and i get the connectivity back : ) I feel much better now. 2011/5/30 Miron Kobelski findko...@gmail.com http://www.mail-archive.com/ccie_voice@onlinestudylist.com/msg21425.html On Mon, May 30, 2011 at 22:13, Cristobal Priego cristobalpri...@gmail.com wrote: do you recall the subject ? I can't find it i found some qos discussions, however it was related to LAN qos thank you 2011/5/30 Bill Lake whl...@gmail.com I believe it was about the first week of May ;) On Mon, May 30, 2011 at 11:52 AM, Friderich Claude cfrider...@netcore.lu wrote: Hi, Look at the forum history, I spoke about this issue and how to manage and resolve this issue a couple of week ago …. ;-) *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]*** *NETCORE PSF S.A.*** 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *adam compton *Sent:* lundi 30 mai 2011 15:45 *To:* Cristobal Priego *Cc:* ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm I've noticed that if you reload BR1 router, it takes a long time for OSPF to populate the routes again. I've had to wait like 5-10 minutes before for the routes to get back on the router. That could possibly be what you're seeing. If that is the case, you should be able to ping the serial interfaces between HQ and BR1, but nothing else on HQ or BR2. Adam Compton On Sun, May 29, 2011 at 11:44 PM, Cristobal Priego cristobalpri...@gmail.com wrote: hello all while doing a mock lab i needed to configure LLQ, MLP LFI cRTP between BR1 and HQ, the bw was 384 when i issued auto qos voip trust fr-atm on both interfaces, after setting the BW on the inferfaces everything was great, no problem however once i reloaded the BR1 router i lost connectivity to the HQ site i reloaded HQ router and still no connectivity so i reverted my pod and resstarted again only with QOS i set the BW and ran the command again without any customization and the same issue happened, where i lost connectivity from BR1 to HQ do you guys know how to fix this ? thank you ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com image001.jpg___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
yes you're right that's what i'm going to do i have never configure it manually so it's a good practice will the qos srnd will tell me how to configure it ? I usually use auto qos, because i'm afraid i'm going to forget something but its something that i'd definitely want to do configure it manually if you know any doc that will let me know how to configure it please let me know i'd really appreciated it thanks 2011/5/30 Friderich Claude cfrider...@netcore.lu This is because you configured with auto-qos. You have to create it manually and it is good for your training and understanding ;-) *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]*** *NETCORE PSF S.A.*** 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* Cristobal Priego [mailto:cristobalpri...@gmail.com] *Sent:* lundi 30 mai 2011 22:55 *To:* Friderich Claude *Cc:* Bill Lake; adam compton; ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm I just tried it and this is what happens I reloaded the router and i don't have connectivity to BR1 now, so i started on the HQ router this is how my interface looks before i make the change interface Serial0/0/1:0.1 point-to-point bandwidth 384 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 201 ppp Virtual-Template200 class AutoQoS-FR-Se0/0/1:0-201 auto qos voip trust fr-atm R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#interface Serial0/0/1:0.1 point-to-point R1(config-subif)#sh R1(config-subif)#no frame-relay interface-dlci 201 ppp Virtual-Template200 as soon as I enter that command I get the Errors below: no frame-relay interface-dlci 201 ppp Virtual-Template200 ^ % Invalid input detected at '^' marker. AutoQoS Error: the following command could not be parsed: no frame-relay interface-dlci 201 ppp Virtual-Template200 R1(config-subif)# *May 31 01:51:19.535: %LINK-5-CHANGED: Interface Virtual-Template200, changed state to administratively down R1(config-subif)# When I try to re-enter the Command on the sub interface this is what i get: R1(config-subif)#frame-relay interface-dlci 201 ppp Virtual-Template200 %vtemplate error; failed to set up PPP-FR circuit R1(config-subif)# and my interface looks like this : ! interface Serial0/0/1:0.1 point-to-point bandwidth 384 ip address 10.10.111.1 255.255.255.0 ip ospf mtu-ignore shutdown snmp trap link-status end 2011/5/30 Friderich Claude cfrider...@netcore.lu For MLP LFI, if you create the virtual-template manually (no auto-qos), it’s going to work. If not, just got to “frame-relay interface-dlci 102 ppp Virtual-Template200” and put no frame-relay interface-dlci 102 ppp Virtual-Template200 Shut the serial interface. Put frame-relay interface-dlci 102 ppp Virtual-Template200 again and no shut the Serial Interface. Do this manipulation on the 2 sites configured with MLP. But for the Lab, normally you just have to reload the routers to make it work. Check with show policy-map interface to make sure that the policy-map is good configured and that you have traffic for sig and RTP Regards, *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]* *NETCORE PSF S.A.* 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* Cristobal Priego [mailto:cristobalpri...@gmail.com] *Sent:* lundi 30 mai 2011 22:13 *To:* Bill Lake *Cc:* Friderich Claude; adam compton; ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm do you recall the subject ? I can't find it i found some qos discussions, however it was related to LAN qos thank you 2011/5/30 Bill Lake whl...@gmail.com I believe it was about the first week of May ;) On Mon, May 30, 2011 at 11:52 AM, Friderich Claude cfrider...@netcore.lu wrote: Hi, Look at the forum history, I spoke about this issue and how to manage and resolve this issue a couple of week ago …. ;-) *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]* *NETCORE PSF S.A.* 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *adam compton *Sent:* lundi 30 mai 2011 15:45 *To:* Cristobal Priego *Cc:* ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm I've noticed that if you reload BR1 router, it takes a long time for OSPF
Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
thank you very much 2011/5/30 Friderich Claude cfrider...@netcore.lu Not so difficult … Check the config with auto-qos and copy paste on notepad Reload the router without saving your config Put your BW in the sub Serial interface Put frame-relay traffic-shaping in your Serial Interface Create your map-class (BR2 for example) Create your own virtual-template (virtual-template 1 for example) Put no ip address and no frame-relay interface-dlci on the sub interface Replace with “frame-relay interface-dlci 202 ppp Virtual-Template1” (for example) Put the new map-class with the name you configured above Don’t forget to apply your policy on the virtual-template Should work …. *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]*** *NETCORE PSF S.A.*** 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* Cristobal Priego [mailto:cristobalpri...@gmail.com] *Sent:* lundi 30 mai 2011 23:23 *To:* Friderich Claude *Cc:* Bill Lake; adam compton; ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm yes you're right that's what i'm going to do i have never configure it manually so it's a good practice will the qos srnd will tell me how to configure it ? I usually use auto qos, because i'm afraid i'm going to forget something but its something that i'd definitely want to do configure it manually if you know any doc that will let me know how to configure it please let me know i'd really appreciated it thanks 2011/5/30 Friderich Claude cfrider...@netcore.lu This is because you configured with auto-qos. You have to create it manually and it is good for your training and understanding ;-) *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]* *NETCORE PSF S.A.* 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* Cristobal Priego [mailto:cristobalpri...@gmail.com] *Sent:* lundi 30 mai 2011 22:55 *To:* Friderich Claude *Cc:* Bill Lake; adam compton; ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm I just tried it and this is what happens I reloaded the router and i don't have connectivity to BR1 now, so i started on the HQ router this is how my interface looks before i make the change interface Serial0/0/1:0.1 point-to-point bandwidth 384 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 201 ppp Virtual-Template200 class AutoQoS-FR-Se0/0/1:0-201 auto qos voip trust fr-atm R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#interface Serial0/0/1:0.1 point-to-point R1(config-subif)#sh R1(config-subif)#no frame-relay interface-dlci 201 ppp Virtual-Template200 as soon as I enter that command I get the Errors below: no frame-relay interface-dlci 201 ppp Virtual-Template200 ^ % Invalid input detected at '^' marker. AutoQoS Error: the following command could not be parsed: no frame-relay interface-dlci 201 ppp Virtual-Template200 R1(config-subif)# *May 31 01:51:19.535: %LINK-5-CHANGED: Interface Virtual-Template200, changed state to administratively down R1(config-subif)# When I try to re-enter the Command on the sub interface this is what i get: R1(config-subif)#frame-relay interface-dlci 201 ppp Virtual-Template200 %vtemplate error; failed to set up PPP-FR circuit R1(config-subif)# and my interface looks like this : ! interface Serial0/0/1:0.1 point-to-point bandwidth 384 ip address 10.10.111.1 255.255.255.0 ip ospf mtu-ignore shutdown snmp trap link-status end 2011/5/30 Friderich Claude cfrider...@netcore.lu For MLP LFI, if you create the virtual-template manually (no auto-qos), it’s going to work. If not, just got to “frame-relay interface-dlci 102 ppp Virtual-Template200” and put no frame-relay interface-dlci 102 ppp Virtual-Template200 Shut the serial interface. Put frame-relay interface-dlci 102 ppp Virtual-Template200 again and no shut the Serial Interface. Do this manipulation on the 2 sites configured with MLP. But for the Lab, normally you just have to reload the routers to make it work. Check with show policy-map interface to make sure that the policy-map is good configured and that you have traffic for sig and RTP Regards, *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]* *NETCORE PSF S.A.* 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* Cristobal Priego [mailto:cristobalpri...@gmail.com] *Sent:*
Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
You only need to issue: no frame-relay interface-dlci 201 ! no ppp Virtual-Template200 shut frame-relay interface-dlci 201 ppp Virtual-Template200 no shut On Mon, May 30, 2011 at 22:55, Cristobal Priego cristobalpri...@gmail.comwrote: I just tried it and this is what happens I reloaded the router and i don't have connectivity to BR1 now, so i started on the HQ router this is how my interface looks before i make the change interface Serial0/0/1:0.1 point-to-point bandwidth 384 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 201 ppp Virtual-Template200 class AutoQoS-FR-Se0/0/1:0-201 auto qos voip trust fr-atm R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#interface Serial0/0/1:0.1 point-to-point R1(config-subif)#sh R1(config-subif)#no frame-relay interface-dlci 201 ppp Virtual-Template200 as soon as I enter that command I get the Errors below: no frame-relay interface-dlci 201 ppp Virtual-Template200 ^ % Invalid input detected at '^' marker. AutoQoS Error: the following command could not be parsed: no frame-relay interface-dlci 201 ppp Virtual-Template200 R1(config-subif)# *May 31 01:51:19.535: %LINK-5-CHANGED: Interface Virtual-Template200, changed state to administratively down R1(config-subif)# When I try to re-enter the Command on the sub interface this is what i get: R1(config-subif)#frame-relay interface-dlci 201 ppp Virtual-Template200 %vtemplate error; failed to set up PPP-FR circuit R1(config-subif)# and my interface looks like this : ! interface Serial0/0/1:0.1 point-to-point bandwidth 384 ip address 10.10.111.1 255.255.255.0 ip ospf mtu-ignore shutdown snmp trap link-status end 2011/5/30 Friderich Claude cfrider...@netcore.lu For MLP LFI, if you create the virtual-template manually (no auto-qos), it’s going to work. If not, just got to “frame-relay interface-dlci 102 ppp Virtual-Template200” and put no frame-relay interface-dlci 102 ppp Virtual-Template200 Shut the serial interface. Put frame-relay interface-dlci 102 ppp Virtual-Template200 again and no shut the Serial Interface. Do this manipulation on the 2 sites configured with MLP. But for the Lab, normally you just have to reload the routers to make it work. Check with show policy-map interface to make sure that the policy-map is good configured and that you have traffic for sig and RTP Regards, *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]*** *NETCORE PSF S.A.*** 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* Cristobal Priego [mailto:cristobalpri...@gmail.com] *Sent:* lundi 30 mai 2011 22:13 *To:* Bill Lake *Cc:* Friderich Claude; adam compton; ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm do you recall the subject ? I can't find it i found some qos discussions, however it was related to LAN qos thank you 2011/5/30 Bill Lake whl...@gmail.com I believe it was about the first week of May ;) On Mon, May 30, 2011 at 11:52 AM, Friderich Claude cfrider...@netcore.lu wrote: Hi, Look at the forum history, I spoke about this issue and how to manage and resolve this issue a couple of week ago …. ;-) *Claude Friderich* *PreSales Support* *CCIE Voice #29035* *[image: CCIEVoice_UseLogo]* *NETCORE PSF S.A.* 49 rue du Baerendall B.P.65 L-8201 Mamer Téléphone: +352 31 33 80 407 Fax: +352 31 33 80 412 GSM: +352 621 303 616 E-mail: cfrider...@netcore.lu *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *adam compton *Sent:* lundi 30 mai 2011 15:45 *To:* Cristobal Priego *Cc:* ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm I've noticed that if you reload BR1 router, it takes a long time for OSPF to populate the routes again. I've had to wait like 5-10 minutes before for the routes to get back on the router. That could possibly be what you're seeing. If that is the case, you should be able to ping the serial interfaces between HQ and BR1, but nothing else on HQ or BR2. Adam Compton On Sun, May 29, 2011 at 11:44 PM, Cristobal Priego cristobalpri...@gmail.com wrote: hello all while doing a mock lab i needed to configure LLQ, MLP LFI cRTP between BR1 and HQ, the bw was 384 when i issued auto qos voip trust fr-atm on both interfaces, after setting the BW on the inferfaces everything was great, no problem however once i reloaded the BR1 router i lost connectivity to the HQ site i reloaded HQ router and still no connectivity so i reverted my pod and resstarted again only with QOS i set the BW and ran the command again
[OSL | CCIE_Voice] CUCME feature ring
Hello, could anybody explain what is the difference between following 2 configurations for feature ring: ephone-dn ring internal/external vs. ephone button 1fY best regards kobel ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] RSVP with CUE
Hey guys, just to bring up an old discussion. Had to prove to myself if transcoder would work as RSVP and it works just fine for me. Not sure what you may be missing, but I got it to work the following way: BR2: dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 rsvp maximum sessions 4 associate application SCCP BR2-RTR#show dspfarm dsp active SLOT DSP VERSION STATUS CHNL USE TYPERSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED 02 23.6.1 UP 1USED xcode 1 0x38130 364 02 23.6.1 UP 1USED xcode 1 0x39431 299 Total number of DSPFARM DSP channel(s) 1 BR2-RTR#show ip rsvp reservation ToFrom Pro DPort Sport Next Hop I/F Fi Serv BPS 10.20.110.1 10.20.110.3 UDP 18280 19100 10.20.112.1 Se0/1/0. FF LOAD 24K 10.20.110.3 10.20.110.1 UDP 19100 18280 none none FF LOAD 24K HQ will be exactly the same. What you must take care of when using transcoder and RSVP on same profile, is that on Region configuration it is important that the transcoders are forced g729 with each other, and then g711 towards the local device. IOS transcoder will always break if tries to talk g729 to one device and g729 towards the other. On my tests, you can notice it reserved g729 and on the phones if I hit the stats, would bring g711ulaw as that's what is talking towards the transcoder. On HQ site, it was valid to replace the transcoder with an mtp too, but BR2 I left it as transcoder and still worked. Cheers! Randall S. 2011/5/19 voice boy voice...@hotmail.com Again you do it Solved :) , you deserve a lot -- CC: ill2...@gmail.com; ccie_voice@onlinestudylist.com From: gogli...@gmail.com Subject: Re: [OSL | CCIE_Voice] RSVP with CUE Date: Thu, 19 May 2011 21:20:12 +0100 To: voice...@hotmail.com Hi voice boy, Do not use xcoder for RSVP. I do not think you would be able to do RSVP and transcoding at the same time with the same dspfarm profile. Do the following: Configure MTP for RSVP again in the following manner: dspfarm profile 1 MTP no codec g711ulaw codec g729r codec passthrough rsvp maximum session software 10 no shutdown And on the CUE side configure xcoder resource with g711 and g729r codec too. It should work now, The problem with RSVP MTP agent is that between sites it normally uses passthrough codec which means endpoints do the codec negotiation. But when the codec negotiation fails between endpoints, like in case of call to CUE, the the RSVP MTP agent needs to negotiate the codec itself, and it tries to negotiate g711 codec because by default that is what it has configured, but it fails because regions have g729 codec limitation. So in MTP RSVP agent after passthrough you must have the codec that you use between sites. In your case g729, but it could be iLBC maybe or anything else. Regards, Sent from my iPad On 19 May 2011, at 19:18, voice boy voice...@hotmail.com wrote: Hi Randl, I use this configuration on both sides HQ and BR router that contain the CUE: dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec passthrough rsvp maximum sessions 3 associate application SCCP hq-rsvp in is HQ-DP [hq-region] br-rsvp is in BR-DP [br-region] both RSVP agents are in different regions, so they talking G729 So I don't know why CUE don't take benefit of the transcoder when it need or RSVP can't invode transcoder !!! -- Date: Thu, 19 May 2011 10:52:46 -0700 Subject: Re: [OSL | CCIE_Voice] RSVP with CUE From: ill2...@gmail.comill2...@gmail.com To: voice...@hotmail.comvoice...@hotmail.com CC: ccie_voice@onlinestudylist.comccie_voice@onlinestudylist.com Take into consideration that the RSVP provisioning is only happening on the route path between the RSVP agents. The CUE itself is outside of the RSVP path. Perhaps what could matter is the codec chosen between the RSVP agents. Whats the region configured between the RSVP agents? Make sure it is G729. What are you using for RSVP agent on HQ? mtp or transcoder? share the config to check. 2011/5/19 voice boy voice...@hotmail.comvoice...@hotmail.com Hi, I'm testing RSVP between 2-ites using RSVP locations It work good and AAR route the call as expected Also TEHO calls consume from the RSVP bw Only the problem is with the CUE at remote site that i think cause it use G711u I was using MTP for RSVP , then when the call forwarded to CUE,, it give not enough bw , call rerouting ,, although there still bw in rsvp I decide to use transcoder as rsvp profile to solve CUE codec issue, But when it is forwarded to CUE, nothing occue nor forwarded to CUE Do I need any thing beside the transcoder profile so CUE can consume from RSVP ?? [note: AAR-CSS AAR-Group EPNM is configured fine for
[OSL | CCIE_Voice] T1 Interface question
I am trying to build a CCIE Voice lab at my house. I am looking at equipment on eBay and nned to know what is the difference between VWIC-2MFT-T1-DI and VWIC-2MFT-T1-DIR and can I use these inplace of a VWIC-2MFT-T1? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CUCME feature ring
The difference is that a dn with 1fY will always ring as a feature ring for all calls on that line. The ring internal/external will make all incoming calls ring as either internal or external no matter what the actual origin of the call is. On Mon, May 30, 2011 at 3:59 PM, Miron Kobelski findko...@gmail.com wrote: Hello, could anybody explain what is the difference between following 2 configurations for feature ring: ephone-dn ring internal/external vs. ephone button 1fY best regards kobel ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com -- Randall da ill Saborio CCIE Voice Wannabe #10054675811 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CME-SRST dn-specific config
You won't be able to accomplish that requirement with provision none. You need at least provision dn and then configure the forwarding on the dns individually, or use call-manager-fallback and then use the alias command for forwarding. Cheers. On Mon, May 30, 2011 at 12:29 AM, Vinay Kumar6 vinayjaisw...@in.ibm.comwrote: Hi, I am testing a scenario, where in I should be able to forward calls to voicemail while in SRST only for selected phones. I am using *telephony-service, *and *srst mode auto-provision none.* Currently for all the the phones Voicemail is working using below config. telephony-service sdspfarm units 5 sdspfarm tag 1 SC-CFB no privacy conference hardware srst mode auto-provision none srst ephone template 1 srst dn template 1 srst dn line-mode octo max-ephones 10 max-dn 10 ip source-address 192.102.66.254 port 2000 system message Your phones are in fallback max-conferences 8 gain -6 call-forward pattern .T transfer-system full-consult create cnf-files version-stamp 7960 Apr 05 2009 12:47:04 ! ! ephone-dn-template 1 call-forward busy 91658200 call-forward noan 91658200 timeout 20 ! ! ephone-template 1 privacy off privacy-button softkeys remote-in-use Newcall CBarge softkeys idle Newcall Redial softkeys seized Redial Endcall Cfwdall Pickup Gpickup Meetme softkeys connected Hold Endcall Trnsfer Park Confrn ConfList Warm Regards, Vinay Kumar ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com -- Randall da ill Saborio CCIE Voice Wannabe #10054675811 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] T1 Interface question
VWIC-2MFT-T1 is a flex port that supports data and voice VWIC-2MFT-T1-DI adds add/drop multiplexing VWIC-2MFT-T1-DIR looks to add drop and insert and relays but might be a specialty product as I only see it listed for 1941-DC Mobile wireless edge router On Mon, May 30, 2011 at 6:42 PM, Bill Hatcher wchatc...@gmail.com wrote: I am trying to build a CCIE Voice lab at my house. I am looking at equipment on eBay and nned to know what is the difference between VWIC-2MFT-T1-DI and VWIC-2MFT-T1-DIR and can I use these inplace of a VWIC-2MFT-T1? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] RSVP with CUE
I just tested it too and it works with the transcoder as Randall said 2011/5/30 Randall Saborio ill2...@gmail.com Hey guys, just to bring up an old discussion. Had to prove to myself if transcoder would work as RSVP and it works just fine for me. Not sure what you may be missing, but I got it to work the following way: BR2: dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 rsvp maximum sessions 4 associate application SCCP BR2-RTR#show dspfarm dsp active SLOT DSP VERSION STATUS CHNL USE TYPERSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED 02 23.6.1 UP 1USED xcode 1 0x38130 364 02 23.6.1 UP 1USED xcode 1 0x39431 299 Total number of DSPFARM DSP channel(s) 1 BR2-RTR#show ip rsvp reservation ToFrom Pro DPort Sport Next Hop I/F Fi Serv BPS 10.20.110.1 10.20.110.3 UDP 18280 19100 10.20.112.1 Se0/1/0. FF LOAD 24K 10.20.110.3 10.20.110.1 UDP 19100 18280 none none FF LOAD 24K HQ will be exactly the same. What you must take care of when using transcoder and RSVP on same profile, is that on Region configuration it is important that the transcoders are forced g729 with each other, and then g711 towards the local device. IOS transcoder will always break if tries to talk g729 to one device and g729 towards the other. On my tests, you can notice it reserved g729 and on the phones if I hit the stats, would bring g711ulaw as that's what is talking towards the transcoder. On HQ site, it was valid to replace the transcoder with an mtp too, but BR2 I left it as transcoder and still worked. Cheers! Randall S. 2011/5/19 voice boy voice...@hotmail.com Again you do it Solved :) , you deserve a lot -- CC: ill2...@gmail.com; ccie_voice@onlinestudylist.com From: gogli...@gmail.com Subject: Re: [OSL | CCIE_Voice] RSVP with CUE Date: Thu, 19 May 2011 21:20:12 +0100 To: voice...@hotmail.com Hi voice boy, Do not use xcoder for RSVP. I do not think you would be able to do RSVP and transcoding at the same time with the same dspfarm profile. Do the following: Configure MTP for RSVP again in the following manner: dspfarm profile 1 MTP no codec g711ulaw codec g729r codec passthrough rsvp maximum session software 10 no shutdown And on the CUE side configure xcoder resource with g711 and g729r codec too. It should work now, The problem with RSVP MTP agent is that between sites it normally uses passthrough codec which means endpoints do the codec negotiation. But when the codec negotiation fails between endpoints, like in case of call to CUE, the the RSVP MTP agent needs to negotiate the codec itself, and it tries to negotiate g711 codec because by default that is what it has configured, but it fails because regions have g729 codec limitation. So in MTP RSVP agent after passthrough you must have the codec that you use between sites. In your case g729, but it could be iLBC maybe or anything else. Regards, Sent from my iPad On 19 May 2011, at 19:18, voice boy voice...@hotmail.com wrote: Hi Randl, I use this configuration on both sides HQ and BR router that contain the CUE: dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec passthrough rsvp maximum sessions 3 associate application SCCP hq-rsvp in is HQ-DP [hq-region] br-rsvp is in BR-DP [br-region] both RSVP agents are in different regions, so they talking G729 So I don't know why CUE don't take benefit of the transcoder when it need or RSVP can't invode transcoder !!! -- Date: Thu, 19 May 2011 10:52:46 -0700 Subject: Re: [OSL | CCIE_Voice] RSVP with CUE From: ill2...@gmail.comill2...@gmail.com To: voice...@hotmail.comvoice...@hotmail.com CC: ccie_voice@onlinestudylist.comccie_voice@onlinestudylist.com Take into consideration that the RSVP provisioning is only happening on the route path between the RSVP agents. The CUE itself is outside of the RSVP path. Perhaps what could matter is the codec chosen between the RSVP agents. Whats the region configured between the RSVP agents? Make sure it is G729. What are you using for RSVP agent on HQ? mtp or transcoder? share the config to check. 2011/5/19 voice boy voice...@hotmail.comvoice...@hotmail.com Hi, I'm testing RSVP between 2-ites using RSVP locations It work good and AAR route the call as expected Also TEHO calls consume from the RSVP bw Only the problem is with the CUE at remote site that i think cause it use G711u I was using MTP for RSVP , then when the call forwarded to CUE,, it give not enough bw , call rerouting ,, although there still bw in rsvp I decide to use transcoder as rsvp profile to solve CUE codec issue, But when it is forwarded to CUE, nothing occue
Re: [OSL | CCIE_Voice] T1 Interface question
There something we should know about the VWIC-2MFT-T1-DI, cause is a little cheaper than the normal one. Can we use the DI like the normal one? I was wondering about that some time ago. Thanks On Mon, May 30, 2011 at 8:49 PM, Bill Lake whl...@gmail.com wrote: VWIC-2MFT-T1 is a flex port that supports data and voice VWIC-2MFT-T1-DI adds add/drop multiplexing VWIC-2MFT-T1-DIR looks to add drop and insert and relays but might be a specialty product as I only see it listed for 1941-DC Mobile wireless edge router On Mon, May 30, 2011 at 6:42 PM, Bill Hatcher wchatc...@gmail.com wrote: I am trying to build a CCIE Voice lab at my house. I am looking at equipment on eBay and nned to know what is the difference between VWIC-2MFT-T1-DI and VWIC-2MFT-T1-DIR and can I use these inplace of a VWIC-2MFT-T1? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] IPPM on cisco7961 didn't alert
Frens, If i can recall correctly, that was due to that i missed associate the phone with application user Phone Messenger. You need the phone messenger application user to control the IPPM user. Without the association, the messaging will still work but funny stuff come out, if not wrong Shingei. On Tue, May 31, 2011 at 4:52 AM, Ki Wi kiwi.vo...@gmail.com wrote: Hey, Do you still remember how did you resolve this alert issue? I'm still trying to train myself up in CUPS. Last night, my alert was working, my IPPM login wasn't. Today my IPPM is working but no alert. =( All other components are working. On Sun, Dec 26, 2010 at 12:59 AM, ShinGei Yong shingei.y...@gmail.comwrote: Guys, Pls ignore this mail, has managed to figured out the caused. thanks Shingei. On Sat, Dec 25, 2010 at 4:36 PM, ShinGei Yong shingei.y...@gmail.comwrote: Hi, I've configure the IPPM on cisco 7961 phone, everything works smooth other that the message receive alert. It doesn't ring when there is a mgs come in from CIPC or other IPPM.i've set the audible alert to ON but still got no luck. Another IPPM phone encounter the same issue, so don't think is the phone problem. Any idea? Thanks Shingei. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
