Re: [OSL | CCIE_Voice] CCIE Voice - IPX Vol1 - Lab 4A - Task 4.7
Hello All, The solution for my issue was both the H323 trunk and Gatekeeper controlled trunk should have the significant digits as 4 for the inbound calls. And the Gatekeeper controlled trunk should have Enable Inbound Faststart. Thanks Ryan for the hint, the only change I did was on the Gatekeeper controlled trunk instead of H323GW. When I did that on H323GW the issue was there so just tried it on the Gatekeeper controlled trunk and removed it on the H323GW, it started working. Thanks, Viki From: Ryan Maxam ryan.ma...@gmail.com To: vignesh sethuraman sethuvign...@yahoo.co.in Cc: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com Sent: Tuesday, 5 February 2013 8:25 PM Subject: Re: [OSL | CCIE_Voice] CCIE Voice - IPX Vol1 - Lab 4A - Task 4.7 I ran into this same problem. if you check Enable Inbound FastStart on you H323 gateway that should correct the problem. Its caused because you are communicating between a SIP trunk and an H323 trunk. On Tuesday, February 5, 2013, vignesh sethuraman wrote: Hello, In the task 4.7 of IPX Vol1 Lab 4A, am able to call and answer the calls to BR2 from HQ and BR1. But when I dial HQ phones or BR1 phones from BR2, am getting a ring back tone but I could not answer the calls. Even after picking the handset, I could hear the ringback on the BR2 phones. I have kept the significant digits as 4 on both the CME (H.323GW) trunk and Gatekeeper controlled trunk. Could you please someone help to resolve this. Thanks, Viki___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CCIE Voice - IPX Vol1 - Lab 4A - Task 4.7
Missed to mention, this issue was faced only when I originate a call from SIP Phone registeredto CME towards SCCP/SIP Phones registered to UCM. If I originate a call from SCCP Phone registered to CME towards SCCP/SIP Phones registered to UCM everything is working fine without Enabling Inbound Faststart on the Gatekeeper controlled Trunk. In either of the case, the significant digits on the inbound calls on both the H323GW trunk and Gatekeeper controlled trunk should be 4. Just sending this as it might be useful to someone facing the same issue. Thanks, Viki From: vignesh sethuraman sethuvign...@yahoo.co.in To: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com Sent: Wednesday, 6 February 2013 10:51 AM Subject: Re: [OSL | CCIE_Voice] CCIE Voice - IPX Vol1 - Lab 4A - Task 4.7 Hello All, The solution for my issue was both the H323 trunk and Gatekeeper controlled trunk should have the significant digits as 4 for the inbound calls. And the Gatekeeper controlled trunk should have Enable Inbound Faststart. Thanks Ryan for the hint, the only change I did was on the Gatekeeper controlled trunk instead of H323GW. When I did that on H323GW the issue was there so just tried it on the Gatekeeper controlled trunk and removed it on the H323GW, it started working. Thanks, Viki From: Ryan Maxam ryan.ma...@gmail.com To: vignesh sethuraman sethuvign...@yahoo.co.in Cc: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com Sent: Tuesday, 5 February 2013 8:25 PM Subject: Re: [OSL | CCIE_Voice] CCIE Voice - IPX Vol1 - Lab 4A - Task 4.7 I ran into this same problem. if you check Enable Inbound FastStart on you H323 gateway that should correct the problem. Its caused because you are communicating between a SIP trunk and an H323 trunk. On Tuesday, February 5, 2013, vignesh sethuraman wrote Hello, In the task 4.7 of IPX Vol1 Lab 4A, am able to call and answer the calls to BR2 from HQ and BR1. But when I dial HQ phones or BR1 phones from BR2, am getting a ring back tone but I could not answer the calls. Even after picking the handset, I could hear the ringback on the BR2 phones. I have kept the significant digits as 4 on both the CME (H.323GW) trunk and Gatekeeper controlled trunk. Could you please someone help to resolve this. Thanks, Viki ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CCIE_Voice Digest, Vol 84, Issue 12
Hi, Voice Mail During SRST Fallback the* vm-integration* *pattern *commands send the appropriate DTMF digits along with the CGN, CDN, and FDN strings to reach the correct mailbox for extension and trunk calling combinations. you need to configure below command : vm-integration pattern direct 2 CGN * pattern ext-to-ext no-answer 5 FDN * CGN * pattern ext-to-ext busy 7 FDN * CGN * pattern trunk-to-ext no-answer 4 FDN * CGN * pattern trunk-to-ext busy 6 FDN * CGN * Cheers, Aditya On Tue, Feb 5, 2013 at 10:30 PM, ccie_voice-requ...@onlinestudylist.comwrote: Send CCIE_Voice mailing list submissions to ccie_voice@onlinestudylist.com To subscribe or unsubscribe via the World Wide Web, visit http://onlinestudylist.com/mailman/listinfo/ccie_voice or, via email, send a message with subject or body 'help' to ccie_voice-requ...@onlinestudylist.com You can reach the person managing the list at ccie_voice-ow...@onlinestudylist.com When replying, please edit your Subject line so it is more specific than Re: Contents of CCIE_Voice digest... Today's Topics: 1. Re: Messages button in SRST (Chrysostomos Christofi) -- Message: 1 Date: Tue, 5 Feb 2013 12:40:22 + From: Chrysostomos Christofi ch.christ...@logicom.net To: Pixar Perfect pixarperf...@live.com, CCIE Voice OSL ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Messages button in SRST Message-ID: f3a446ed84ff9449b29f801927620de783f8b...@exmbxsrv2.lgcom.net Content-Type: text/plain; charset=iso-8859-7 Hi It looks fine the configuration that you described regarding of the requirements As the question about the Proctor ,i believe that no ones can answer that From: ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] On Behalf Of Pixar Perfect Sent: ?, 5 ??? 2013 10:36 ?? To: CCIE Voice OSL Subject: [OSL | CCIE_Voice] Messages button in SRST When Site B Phone 2 (DN 3002) hits the messages button in SRST, the SRST call control dials 912025552220 to the PSTN to ring the Voicemail ports at Site A. Unity plays generic Welcome greeting instead of the user greeting of user 3002. The requirement is NOT to use Alternate Extension on the user. Another requirement on the Voicemail question is customize user 3002 so user can hear the ANI and timestamp of the caller. IPExperts solution to the 1st requirement is to use calling number mask under hunt pilot. However this breaks the second requirement, as Unity Connection will only receive 4 digits ANI even for standard PSTN callers. Any comments of this use of could be graded and any experiences? I have a workaround that would cater to users at SiteB hitting messages button to check messages: 1) Setup the voicemail DN in SRST to 912025552225 2) User hits messages button and SRST/CME dials 912025552225 to Site A 3) At the CUCM, setup a translation pattern to translate 2225/pt-gw-sa-only to 2220 and this same translation pattern masks the calling number . CSS (css-internal) on the translation pattern would be able to access the VM hunt pilot 2220 4) Site B dialing 2225 for VM access would give the CUCM intelligence to differentiate a PSTN call to VM versus a call from Site B to VM via PSTN. Due to the translation pattern configured the calling number presented to the CUC would be i.e., 3002 CFNA and CFB at Site B SRST would still use 912025552220. Here is the call flow for CFNA and CFB in SRST 1) PSTN phone calls Site B Phone 2 (SB-Ph2) while Site B is in SRST 2) SB-Ph2 ring no-answer to voicemail DN which is setup as 912025552220 3) Call hairpins back to PSTN to dial the VM pilot 2220 at Site A. ISDN setup carries RDNIS set to 3002 4) CUCM receives RDNIS in the call, rings the hunt pilot 2220 and delivers it to Unity Connection to identify VM Box. I have tested these approaches in the lab and each works like a charm, not sure if proctor deems this as a valid solution. Any thoughts? -- next part -- An HTML attachment was scrubbed... URL: /archives/ccie_voice/attachments/20130205/1f90d955/attachment-0001.html -- ___ CCIE_Voice mailing list CCIE_Voice@onlinestudylist.com http://onlinestudylist.com/mailman/listinfo/ccie_voice End of CCIE_Voice Digest, Vol 84, Issue 12 ** ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] MGCP GATEWAY
Hi Ben, Yes. You have to add ccm-manager fallback-mgcp for the MGCP in SRST scenario. *Configuring MGCP Gateway Fallback and Cisco SRST ** *** * To make outbound calls while in SRST mode on your MGCP gateway, you must configure two fallback commands on the MGCP gateway. These two commands allow SRST to assume control over the voice port and over call processing on the MGCP gateway. With Cisco IOS releases prior to 12.3(14)T, you must configure MGCP gateway fallback by using the ccm-manager fallback-mgcp and call application alternate commands. With Cisco IOS releases after 12.3(14)T, you must configure MGCP gateway fallback by using the ccm-manager fallback-mgcp and service commands. * http://www.cisco.com/en/US/docs/ios/12_3/vvf_c/interop/intcnf1.html Regards Gurpreet On Tue, Feb 5, 2013 at 7:41 PM, Ben John benjoh...@hotmail.com wrote: -- Guys I configured MGCP on a E1 controller using cc-manager config server it generated the output below. Is there anything wrong with the config ? I want to know if it is safe to do it during the real lab. It works in my own lab. Please advise. ccm-manager redundant-host 192.168.1.41 ccm-manager mgcp no ccm-manager fax protocol cisco ccm-manager music-on-hold ! mgcp mgcp call-agent 192.168.1.42 2427 service-type mgcp version 0.1 mgcp modem passthrough voip mode nse mgcp package-capability rtp-package mgcp package-capability sst-package mgcp package-capability pre-package mgcp default-package mt-package no mgcp timer receive-rtcp mgcp sdp simple mgcp fax t38 inhibit mgcp bind control source-interface Vlan502 mgcp bind media source-interface Vlan502 ! mgcp profile default If the site is going to be an SRST can i add the following commands ? ccm-manager switchback immediate ccm-manager fallback-mgcp Ben ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] MGCP GATEWAY
Hi All my Friends, If the question is asked for configuring busy out few channels from MGCP gateway is it just enough if we used. But if it not mentioned how many channels we need to busy out what woul be correct. Just open a all channels or keep busy few ?? *pri-group timeslots [1]-[X] service mgcp * [1]-[X] is number of channels question mentioned. at the same time do we need to use RTMT to do Deep Level MGCP monitoring. Such as a mgcp call debug output. Sorry about not opening new mail for this. Thanking you as always, Ravi. :) ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] UCCX - Adding cucm trigger failed
Jason said it all, I would say make sure the Dn you're using to create the trigger is available in the CM. Regards Gurpreet On Tue, Feb 5, 2013 at 4:47 PM, Jason Aarons scubajas...@gmail.com wrote: Check your CCM replication, and verify no un-asigned DNs. ** ** Reset your jtapi user/password, and restart UCCX Node Engine. ** ** *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *CCIEing *Sent:* Tuesday, February 05, 2013 2:31 PM *To:* ccie_voice@onlinestudylist.com *Subject:* [OSL | CCIE_Voice] UCCX - Adding cucm trigger failed ** ** Hello everyone, ** ** I restore my UCCX to it's fresh install status, them I went through the integration steps, I configured an application then when I tried to add the trigger the ** ** system failed to add this trigger, This message appear Could not update the user on the Cisco Unified CM. ** ** Attached you can find the screenshot for the error. ** ** Notes - there is no number in the CUCM with DN 1250. - both uccxjtapi and rmcm users are created on CUCM ** ** Any idea please. ** ** Thanks ** ** ** ** ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
