Yes APF came out reel good, very well done! Don´t even know if
it was this good on the FT-1000D, at least not on the units I
did own.
Now if only AM RX was to be fixed I would be happy, as it is
right now AM (not sync AM) RX is more or less useless. It got
broken in the DSP code way back. I have
This occurs in running in a contest, where you have positioned the
hard skirts of roofing and regular DSP, to keep out the strong
stations just above and just below. A weak station down in the noise
calls you slightly up or down, but not out of your running passband.
If you tune the RX frequency
Hello!
I am looking for an used KFL3A-400 CW Filter.
If you have one for sale, pse Email me.
73s Alex NH7VW
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Wanted-Elecraft-K3-filter-KFL3A-400-tp5704331p5704331.html
Sent from the [K3] mailing list archive at
Hello elecrafters
Thinking about the 2m external transverter or the internal unit. Wich
one is better ? Worth ? Or maybe just another rig like 857 ?
Tnx
PY2ADR
__
Elecraft mailing list
Home:
On Thu, 4 Nov 2010 06:54:06 -0200, Adriano Perazio
adriano.pera...@uol.com.br wrote:
I have both and prefer the internal version.
Tom
Radio Amateur N5GE
Hello elecrafters
Thinking about the 2m external transverter or the internal unit. Wich
one is better ? Worth ? Or maybe just another rig
Hi Adriano,
I use the K144XV Internal unit and I reckon its a better buy than the external
unit for a couple of reasons.
1: Convienience - No external cables to lose!
2: Coverage of the full 2m band versus only 2MHz coverage of the external unit.
The only down side is the lower output of the
As I am now to decide to buy K144XV or stay with some external - let
me ask here:
What is thermal stability of internal 116/118MHz Xtal osc?
I mean some experience with JT data mode in EME or similar. Is there
some drift on 144MHz signal (during longer TX period) and how much if any?
Thanks
Hi Alexandr,
I have not noticed any drift at all with my K144XV with internal temperatures
to +60 degrees C.
I must admit though at this stage I have not used it for digital modes, only
SSB + FM.
No-one has ever commented about any drift on my signal.
Jeff Cochrane - VK4BOF
Innisfail, QLD,
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
Adriana Lexa -
I have both the external XV144 and the internal K144XV. While they both
have their advantages and disadvantages it all depends on what you want
to use them for.
For frequency stability the XV144 (with crystal oven) is far superior
although Elecraft are currently doing some
This is a suggestion the Menu pages (currently 52-63) of the K3 manual be made
available separately on the Elecraft Homepage in the Manuals and Downloads
section.
The newly added items to the Menu could be kept up-to-date in PDF format, and
one could easily print them for reference.
This
Thanks David,
it is as I suppose to be - I will wait for PLL add-on to K144XV for my
purposes, no problem as I have stable external now (home made with
DB6NT heater on Xtal).
Thanks for your report,
Lexa, OK1DST
Dne 4.11.2010 11:27, David Pratt napsal(a):
Adriana Lexa -
I have both the
I think this a good idea as I am totally losing the plot with all of the
excellent F/W improvements (and how to use them)
that are being made to the K3 on a regular basis.
73
Stewart G3RXQ
On Thu, 4 Nov 2010 06:31:20 -0400 (GMT-04:00), Bill McDowell wrote:
This is a suggestion the Menu pages
Hi Jan
I agree. The K3's APF just blows away the APF on both the IC7600 and IC7700.
The K3s APF is in a league of its own.
I cant stand using my FT1000D anymore with all its peak clipping and IMD on
audio peaks. The might dog is fast becoming a real boat anchor, but sometimes
I need 200
I agree. The K3's APF just blows away the APF on both the IC7600 and
IC7700. The K3s APF is in a league of its own.
Icom doesn't use a peaking filter. Their implementation of APF is really an
Audio Passband filter, rather than an Audio Peaking Filter. When
engaged, their APF filter skirt
Hello,
I have my K3 ACC connected to a Bandecoder (Arraysolutions Bandmaster) that
change bands in the SixPack automatically.
Now I want to connect a ALS 1300 Amplifier with the optional ARI-500 radio
interface. And I need to connect it to the ACC of the K3 also!...
So how can I do to
...So how can I have Bandecoder and ALS1300 both connected to the K3 so
when I change bands in the K3, automatically change bands in the ALS1300 and
select the right antenna in the sixpack?...
You just need a DB15HD Y-adapter cable so the K3 band data feeds both the
BandMaster and ARI-500
Hi Bill,
That's an excellent request. Then you could do a search within this small
PDF for short phrases. Now if you search the entire manual for a single word
you get many hits until you finally reach page 52.
73,
Mike K2MK
William G. McDowell wrote:
This is a suggestion the Menu pages
John,
A 20 Hz mis-tuning of a SSB signal usually will not be noticed, 50 Hz
maybe, and 100 Hz definitely.
So yes, you would normally tune the station until it 'sounds right' and
then transmit. That assumes that you are using the same filter for
transmit and receive.
You can make some
Thanks Phil,
I doubt this will work, but seems is easy.
My local store have this Y adapter, I don´t know if it´s exactly a DB15HD
model, but hopefully any DB15 Y will work.
Thanks!
Jorge
CX6VM
-Mensaje original-
De: elecraft-boun...@mailman.qth.net
Well, I just wasn't sure I would use it, I had such good results with
just the DUAL PB function. So I sought out the weakest signal I could
find this morning, R5ZZ, who was not copiable here, but I could hear
some Ws working him. I dialed in the APF and there he was, and
copiable. So mea
To this old dog's ears there is way too much ringing.
Even in my EME days I never felt the need for these super narrow filters. I
used a passive 200 Hz wide filter centered on 600 Hz. A few hours of listening
to noise in a too-narrow filter and you start hearing things that aren't there,
I agree Wes, way too much ringing for my taste. I have never cared for the
ultra narrow filters myself.
I listened using the APF on 80 cw last evening, works well but the
distortion certainly hurts the copy.
Jim K4JAF
- Original Message -
From: Wes Stewart n...@yahoo.com
To:
I don't see this as something that would be left on ALL the time. Only used as
needed. It does help make an
otherwise unworkable station readable for a contact. Just another tool in the
box. When you don't need it, turn it off. I have not tried this yet
but you can probably turn it off
There was a suggestion posted within the last few days to reduce the
ring by adjusting the APF SHIFT along with RIT by 20 Hz. This might
make a nice one--push macro but I don't think there is a APF SHIFT
command available yet (The IF SHIFT command does not work in APF.)
Also, for for those who
Hi,
I would like to ask for help. My K2 #4800 works fine but I realized the
narrower filters have attenuation. I pre-set FL1200Hz, FL2400Hz and
FL3700Hz but with FL1 I recognised too much attenuation which degrading the
reception of weaks sigs. Is there something which I am doing wrong please?
For this old dog it is great !
I very much like the peak, works very well at pulling the weak signal up
for much better copy. Congratulations Elecraft this is a super tool for CW !
Now the bad news.
My Yaesu FT1000 was switched in when needed on CW receive just for the APF to
pull
a
This method does diminish the ringing -- offsetting the APF peak using SHIFT
and the receive frequency using RIT. 20 Hz seems to be about right, too. The
bad ringing only occurs when the peak frequency and the center of the
passband coincide exactly. I had a lot of fun this morning, right after
I updated my K3 to MCU 4.17 beta last night along with DSP 2.65 and FPU
1.4(?) and now today I notice that my SSB output is down about 3 dB. I
can only coax about 50 Watts peak out of it and I've made no changes to
microphone, TX EQ, Mic Gain, Compression, or output power (set to 100 W).
Additional testing shows that when I set my power down to 5 Watts and
then back up to 100 Watts results in a max peak output of 50 Watts on
SSB on both an external and the K3's Wattmeter. Setting the mode to CW
results in 100 Watts output and reverting back to SSB I can get about 75
Watts peak
Greg,
I agree 100% It is a tool and is there for the specific use of pulling a weak
CW signal up out of the mud
so you can copy him. Turn on when needed. The Yaesu FT1000's, early issues,
had great APF
and had a little ringing but they worked very well, the little ringing goes
with the
Power failure in middle of firmware load and now cannot connect with K3.
Anyone know how to get started again?
Jim, W5ODD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I received some helpful suggestions from The Smiths regarding APF,
specifically using RIT to shift the received signal down 20 Hz or so and
using
APF Shift to peak the signal. The purpose is to make the tone of the
received signal 20 Hz lower than the faint ringing noise induced by APF.
This
Nate, have you tried reloading the firmware? I'd give that a shot first. If
that doesn't help, revert to the previous version and test again.
In my case, latest beta firmware installed with no issues to report.
73 de James K2QI
--Original Message--
From: Nate Bargmann
Sender:
Turn off rig and close the K3 utility. Then try it again.
James K2QI
--Original Message--
From: Jim Bobo
Sender: elecraft-boun...@mailman.qth.net
To: Elecraft Reflector
Subject: [Elecraft] Firmware load
Sent: Nov 4, 2010 13:54
Power failure in middle of firmware load and now cannot
I dunno about the loss you are seeing but I've measured about 8 dB of
loss in my K2 at 200 Hz vs 1 kHz BW. That does strike me a quite a bit
of loss. I just don't use the narrow filters often. I know of at least
one other K2 that has similar loss. Anyone else?
73 de dave
ab9ca/4
On
In a word, yes
Jim, W4ATK
On Nov 4, 2010, at 12:18 PM, Nate Bargmann wrote:
I updated my K3 to MCU 4.17 beta last night along with DSP 2.65 and
FPU
1.4(?) and now today I notice that my SSB output is down about 3
dB. I
can only coax about 50 Watts peak out of it and I've made no
I went through the CONFIG menus to see what might have changed while
in SSB. I found DUAL PB had APF on. I was unable to turn it off while
in SSB, so went back to CW mode turned the APF off (nor) and returned
to SSB and all was normal. Full output.
I have confirmed you can only turn APF
I'm new to all this. I noticed a lower output last night as well,
after the ...17 load. Should we do a calibration and configuration
after a FW update? Time to get out the SG2 again?
...bc
BTW: the APF looks real cool. I'm not a CW operator, but this makes
me drool a little bit.
I don't have any lack of ssb power output here after the new download with
APF enabled in config.
IO have to say I think the new APF is very good indeed. Running 4.17 on the
K3 and 00.41 on the P3.
73 Stephen G4SJP
On 04/11/2010 18:56, n...@widomaker.com n...@widomaker.com wrote:
I'm new
I use an xv-144 for jt65 eme. It will drift slightly for about 20 minutes after
power up, even with the xtal oven. However, i have mine strapped so the
oscillator and oven are only running when it is turned on. After warmup it is
rock solid--no drift.
73
Eric WD6DBM
Sent from my $...@!?
...My local store have this Y adapter, I don´t know if it´s exactly a
DB15HD
model, but hopefully any DB15 Y will work...
Many DB15HD Y-cables don't have all the pins connected straight thru, and
may even short some of the wires to each other and to ground. Make sure you
check each individual
Power fine here with 4.17. Get full 100W PEP out on both CW and SSB and the
drive power that I normally use for my amp is as accurate as it always was.
Checked two K3s with an Alpha 4510, an LP-100A and an Array Solutions
PowerMaster. I don't see anything different at all regarding power
Winford Engineering has them. Though it is not showing on their website.
If you go to an empty shopping cart and enter CDY15HDMFF-1 it will show up.
They're $15. Male on one side and two females on the other. They stock these
almost exclusively for K3 owners. :)
www.winfordeng.com
(I
Yes, Eric, like you I usually switch on my XV144 for about 20 minutes
before I intend to use it to allow the crystal oven to get up to
temperature. Then, it is nice and stable. I did have the Mitsubishi PA
module fail on me and had to replace it. I have also fitted an internal
fan similar to
* On 2010 04 Nov 14:06 -0500, Stephen Prior wrote:
I don't have any lack of ssb power output here after the new download with
APF enabled in config.
Interesting. Thanks to Jim for finding that setting Dual PB to Nor will
correct this. Hopefully, Wayne is reading this thread. :-)
IO have to
Hi all,
There's a bit of confusion on this point. The DUAL PB switch still
functions exactly the same as it always did when in RTTY mode. The new
CONFIG:DUAL PB menu entry (to select NOR or APF) applies *only* to CW
mode.
73,
Wayne
N6KR
I am unable to duplicate your conditions, I am only able to get APF on
in CW mode. Wonder if this would be something where a previously
uncontrolled memory bit is in an undetermined state, leaving a strange
remembered condition when those bits are used for the first time?
73, Guy.
On Thu, Nov
Dave,
yes I am confirming it is the attenuation which I am talking about...
When I am decreasing BW from 1.5k to 700Hz there is not noticeable att
(which means it's aprox. less then 3dB) but by going to 400Hz or even to
200Hz I hear big att which can be like You said 8dB or so.
Anybody else has
Thanks Greg, Phil and others for the nice help...
I just bought a Manhattan Y adapter HD15M to 2xHD15F. I tested it and it
have all 15 pins availables.
Next weekend will be in the station to test it.
Thanks!
73,
Jorge
CX6VM/CW5W
-Mensaje original-
De: elecraft-boun...@mailman.qth.net
Regarding my previous message on APF macros--
I had to change the name of APF SHFT to APF SHF (discovered the
character limit when saving the macros to M4T and M4H on my K3.)
Since the APF function seems to save the last shift used, it seems
less important to include an APF shift in the macro.
Hope someone can use it. Top in near new condition - replaced with the
battery top. Includes the 4 little screws. Price? I don't have a clue - so
- how about $10 and you pay for Priority Mail? See a couple of photos at:
http://www.flickr.com/photos/n4hh 73 es gud dxing -- Don N4HH
1. When I start the utility, not the firmware loader but the run time
utility, it starts with a very bizarre window, not movable, only closable by
Task Manager and the top is off the top of the screen. I deleted the
executable and downloaded a new copy but get the same behavior. It appears
On Thu, Nov 4, 2010 at 9:23 PM, Jim Spears n...@cox.net wrote:
1. When I start the utility, not the firmware loader but the run time
utility, it starts with a very bizarre window, not movable, only closable by
Task Manager and the top is off the top of the screen. I deleted the
Jim,
What is your Operating System? Had you installed before?
I have the unit and it works fine on WIN7 PRO 64 Bit. I have also tried it
on WIN7 32 Bit as well. Do you have firewall or Antivirus software, and if
so, what.
Your desktop would appear to be corrupted not to run this program.
Remove power connector from K3.
If a P3 is inline, remove P3 power connector so that P3 will not power up, even
for a moment, when you reapply K3 power.
Reboot PC. This isn't often necessary, but sometimes a COM port or USB driver
is in an awkward state. If you don't reboot, do stop the K3
I had this same problem.Worked around it by temporarily reducing
the PC's video screen size and then restoring it, with W2 running.
That at least moved to a point where I could drag it.
73 Jack KZ5A
K3 #4165
On 11/4/2010 4:35 PM, Bill K9YEQ wrote:
Jim,
What is your Operating System?
That is the W2 firmware load utility registry key. He's asking about W4SMT's
utility
Dick
On Nov 4, 2010, at 14:30, Iain MacDonnell - N6ML a...@dseven.org wrote:
On Thu, Nov 4, 2010 at 9:23 PM, Jim Spears n...@cox.net wrote:
1. When I start the utility, not the firmware loader but
Perhaps this process should be appended to the K3 FAQ or troubleshooting areas,
as this topic comes up quite a bit on the reflector.
Cheers,
James K2QI
Sent via BlackBerry from T-Mobile
-Original Message-
From: Dick Dievendorff die...@comcast.net
Sender: elecraft-boun...@mailman.qth.net
I'll add it to K3 Utility Help. TU, good idea.
Dick
On Nov 4, 2010, at 15:16, k2qi@gmail.com wrote:
Perhaps this process should be appended to the K3 FAQ or troubleshooting
areas, as this topic comes up quite a bit on the reflector.
Cheers,
James K2QI
Sent via BlackBerry from
Jim needs to fill us in on what is running. I have all equipment plugged
in. I have the works. The W2 requires a second RS232 or remove from one
external device and move to another. If that is being done then there are
other things to consider. (This is where internal USB converters can make
Last month we were talking about external speakers for the K3. I have a pair
of like new Insignia speakers for sale.
If you sit them beside your K3 they are about 1 inch taller (rig propped up on
its stand). Black.
$15 for one, or $25 for both. Shipping about $10. Contact me off list
I remember seeing a QST test of the internal K144XV, I believe it was in
August this year, where its large-signal handling specifications were
inferior to the external XV144. Please correct me if I am wrong on this, and
if not I would like to understand why.
-
Sverre, LA3ZA
K2 #2198, K3
I had no loss of SSB power output after the 4.17 Beta install. The APF
works wonderfully, with only a hint of ringing to my ears. Really nice
addition to the K3.
--Dave, W8OV
On 11/4/2010 3:11 PM, Nate Bargmann wrote:
* On 2010 04 Nov 14:06 -0500, Stephen Prior wrote:
I don't have any lack
* On 2010 04 Nov 18:23 -0500, Dave, W8OV wrote:
I had no loss of SSB power output after the 4.17 Beta install. The APF
works wonderfully, with only a hint of ringing to my ears. Really nice
addition to the K3.
At least some of you aren't seeing this. :-)
James Rogers suggested turning
Please retry TX gain calibration on affected bands. This is the usual
cure for a difference between CW and SSB power output.
Wayne
N6KR
http://www.elecraft.com
On Nov 4, 2010, at 4:30 PM, Nate Bargmann n...@n0nb.us wrote:
* On 2010 04 Nov 18:23 -0500, Dave, W8OV wrote:
I had no loss
Hi Gang,
During my last contest foray, I noticed that making Qs on 15M was difficult.
Turns out that with only about 50mW, it is! And 17M is likewise low. The
rest of the radio is FB. Also, the current draw on 15/17 is basically the
same in RX and XMIT.(My Astron's meter moves about one needle
Well, rolling back is worth a shot. I've never had problems reverting to
previous versions. Plus, look at it this way - what variables have changed? If
this issue manifested itself after the last fw update, then that should be a
good place to start.
James K2QI
Sent via BlackBerry from T-Mobile
I am seeing the same reduction in SSB output power. I installed 4.17 Beta
last night. It appears that the reduced power only occurs when I have APF
activated. I have twice restored SSB power by doing the following: 1).
Changing mode back to CW, 2). Going to Dual PB in Config menu and
On Thu, 4 Nov 2010 19:52:12 +, David Pratt da...@g4dmp.fsnet.co.uk wrote:
I leave my K3's on all the time, but yes the K144XV does drift a bit, so before
doing anything that requires stability I hold the CW Key down for about 5
seconds to warm things up.
Tom
Radio Amateur N5GE
Yes, Eric,
Hi Dave,
In CW mode, in CONFIG:PB CTRL, what value is in SHIFT= ??
Thanks, Guy.
On Thu, Nov 4, 2010 at 8:34 PM, Dave Perry N4QS n...@comcast.net wrote:
I am seeing the same reduction in SSB output power. I installed 4.17 Beta
last night. It appears that the reduced power only occurs when I
Yes, mine attenuates but haven't bothered to measure it. Strangely, the 700
Hz seems worse than the narrower filters.
Curt KB5JO
I dunno about the loss you are seeing but I've measured about 8 dB of
loss in my K2 at 200 Hz vs 1 kHz BW. That does strike me a quite a bit
of loss. I just don't
I'm playing with the new APF, and trying to get a REALLY weak QSO to pop. I
have the
volume cranked up pretty good, and a REALLY strong station throws in their
call. I
thought my speakers had blown. Glad I wasn't wearing cans.
My CONFIG:AF is 18, AGC = F.
Was I doing something wrong? Anybody
Now I seem to have a real problem. I did a TX Gain calibration using the K3
Utility for both 5 and 50 watts. I worked perfectly and tx gain appeared to
be right on all bands. I then did some testing into a dummy load with RTTY.
I noticed that power would start out at 25 watts and it would
OK, my SSB output was low too. I'm on phone so rarely, were it not for
the reflector, I'd probably never have checked and when I did find out,
the thread would have already died. I did the TX Gain calibration as
Wayne suggested, all seems to be well on all bands. Apparently, the DL
in my
Guy,
I solved the audio problem. Speakers had somehow been set to 1. Turned it
back to 2. But WMTR parameter is totally missing. So I guess I will try
reverting back to 4.14.
Dave
- Original Message -
From: Guy Olinger K2AV olin...@bellsouth.net
To: Dave Perry N4QS
* On 2010 04 Nov 21:10 -0500, Dave Perry N4QS wrote:
Now I seem to have a real problem. I did a TX Gain calibration using the K3
Utility for both 5 and 50 watts. I worked perfectly and tx gain appeared to
be right on all bands. I then did some testing into a dummy load with RTTY.
I
Petr,
I measured mine at 500 Hz a few years ago but never wrote down the
number. I do remember being surprised at how much it was. I use a wider
filter most of the time and only go to the narrowest when there is
substantial qrm in the passband; for just the reason you mention.
73,
Lenny
You can adjust the ssb filter by listening to your own voice on the
rig and adjusting the ssb filter to what sounds best to you. To monitor
your own voice set the SSBA option to BAL. Then got to CAL FIL for the
filter you want to adjust and adjust it (a little at a time) while
talking into
Same thing to me, I was noticed it when put my Amp w/GU84B on, need 20w+ to
obtain 500w in ssb instead of my normal 16w. MH2 Mic dynamics was also
affected and obliged to increase the Mic gain consequently.
When back to NOR Dual PB features it comes back almost to normal power but
seems a bit
We're working on the SSB problem.
73,
Wayne
N6KR
On Nov 4, 2010, at 9:49 PM, Philippe Trottet wrote:
Same thing to me, I was noticed it when put my Amp w/GU84B on, need
20w+ to obtain 500w in ssb instead of my normal 16w...
__
Mark,
How is it on 10m and 12m?
Leigh/WA5zNU
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K2-10-SN-543-Lower-Po-on-15-17M-tp5707375p5707851.html
Sent from the [K2] mailing list archive at Nabble.com.
__
82 matches
Mail list logo