Hello,
I am currently trying to build up and install a KAT1 into my K1 # 154. I have
just updated the firmware to version 1.09 and made all changes of the K1
upgrade kit. Now I am working my way through the KAT1 assembly and operating
instructions revision C, Jan. 18, 2001. I am stuck at page
If you look at K1 builder alert #1, R39 is discussed there. C76 is installed
right next to it. Look also at the schematic for the K1 page 79 Appendix B RF
Board in the lower left hand corner where C75 and R39 are shown.
Here is the builder alert #1...
K1 builder alert: Minor T-R switch mod
Thanks to everyone for the quick response,
I solved the problem. The modification was first mentioned in the K1 builder
alert #1 and is also found in the later than revision C manuals. The actual
description on how to do the modification or how to solder in RF-R39 varies on
the revision number
I got a useful suggestion from Tucson AZ.
I updated the KX3 command Visual index. It was Color coded for SET / GET
distinction .
Please download the latest one from following URL.
jf1vru.blog65.fc2.com/blog-entry-348.html
Thank you for your comment and suggestion.
Shibu JF1VRU
Will the KX3 DVR be able to record what the receiver is hearing or just what
the mic hears?
Pete WK8S
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
It is for messages only, not recording off the air.
The Flash used in the KX3's DSP requires a longer erase time than it
takes record, so it can not keep up in a real-time recording loop.
73,
Lyle KK7P
Will the KX3 DVR be able to record what the receiver is hearing or just what
the mic
On page 52 it says tap 3 to turn on an additional front panel mic gain stage -
but in fact it’s tapping 7 that turns it on.
73
Geoff
G3UCK
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
You should be able to just use the the audio in/out cables and your
PC sound card. Be careful however that your 'PC' sounds are not
also transmitted.
On Fri, Feb 8, 2013 at 6:49 PM, Gil G. g...@keskydee.com wrote:
Hello,
I am wondering if I really need a Signalink USB box to use RMS
Less than 1 hour operating time. Perfect condition. Shipped in custom
carton built by Dave at hamradioboxes.com. Perfect setup for DXpeditions.
More info at: w0fm at arrl dot net
Terry Schieler, W0FM
__
Elecraft mailing list
I need a little help getting my K3 with footswitch plug into the back of the
K3 PTT IN to key the Enter Send Mode (ESM) in N1MM. I'm assuming there
is a way that I can pass the footswitch closure through the K3 radio and
using LP Bridge into N1MM to act as if I hit Enter on the keyboard.
So
Bill,
The transmit/receive information will be sent to N1MM in response to an
IF command issued by N1MM or in response to a TQ command (again issued
by N1MM). The TX.RX state is not included in the AI meta command (see
the K3 prorammer's reference).
You may have to ask the N1MM forum for
Gil,
You do not need a SignaLink box to use any data modes, including RMS
Express - just feed the audio in an out to the soundcard.
You may need a galvanic isolator (transformer) between the KX3 and the
soundcard to improve the signal to noise ratio and reduce ground loops.
The audio level
Hello
Having received a XG3 for Christmas, I decided to calibrate the RF Gain on
the K3 which I have had for over a year now. Using the RF gain calibration
routine in the K3 utility, I had an issue while going through the gain
routine with the subreceiver.
First time through, the main receiver
Effectively you would be asking the K3 to control N1MM Logger's TX/RX
status. I'm quite sure you can't do this - the control goes the other
way (from N1MM Logger to the rig).
The normal way to set this up is to connect the footswitch to the
computer via a serial or parallel port interface,
Jim,
That solved the problem.
Thanks,
Dan
W6DAS
On 2/9/13 4:43 PM, Jim Sheldon w...@cox.net wrote:
Dan, you need to upgrade your K3 Utility program to the latest one -
1.12.10.10, and the current production release of the software is 4.60. The
FPF you have, 1.15 is still current but both
divnbsp;nbsp;nbsp;brnbsp;/divdiv style=color: rgb(0, 0, 0);
font-size: 16px; font-family: times new roman,new york,times,serif;
background-color: transparent; font-style:
normal;nbsp;http://www.jardindesimpressions.com/hya/kzo0.be?vp=uw8nbsp;nbsp;nbsp;br/divdiv
style=color: rgb(0, 0, 0);
Well done Nick! I like your remote button knob kit very much. Please keep
us posted on your progress. I'm interested and suspect Elecraft is as well.
Gary N6LRV
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Nick Garner
I thought 40M signals sounded kinda low, and the noise floor on the P3 was
down - but then noticed when I turned the KP!500 from OPER to STBY, signals
came about 15db. No fault indicated. TX power seems fine. Any thoughts?
John K3TN
--
View this message in context:
On Sat, 9 Feb 2013 19:51:09 -0800 (PST), John K3TN wrote:
I thought 40M signals sounded kinda low, and the noise floor on the P3 was
down - but then noticed when I turned the KP!500 from OPER to STBY, signals
came about 15db. No fault indicated. TX power seems fine. Any thoughts?
I'm
Elecraft CW Net Report for January 27th 28th, 2013
On 14049.5 kHz at 2300z:
NO8V - John - MI - K3 - 820
W0CZ - Ken - ND - K3 - 457
N0TA - John - CO - K3 - 994
AC5P - Mike - OK - K3 - 2170
K0DTJ - Brian - CA - K3 - 4113
W8OV - Dave - TX - K3 - 3139
N0AR - Scott - MN - K2 - 4866
On 7045 kHz
Good Evening,
It has been a foggy week. I have seen the dewpoint follow the
temperature step for step as the fog stays heavy. There was a brief
glimpse of the sun yesterday so I took a short walk. Good thing it was
short because the dark clouds came back and it started raining before I
The weekly Elecraft SSB net will meet tomorrow (2/10/13) at 1800Z on 14.3035
MHz +/- QRM. I will be the net control from western Oregon. See you there.
73,
Phil, NS7P
__
Elecraft mailing list
Home:
22 matches
Mail list logo