[Elecraft] Dx Commander Settings for K3s

What are the Baud Word Parity Stop DTR RTS Settings for the K3s AJ4YA Grady Thanks Sent from my iPad __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

Re: [Elecraft] K3/0 control not working with DXLap or N1MM

Jeff, I can connect the the K3 at the remote transmit site or via local LAN - only difference is the "SIP CONTACT" address in "RADIO SETTINGS" on the RRC Control. I use DHCP for the control RRC when on the LAN. Can you connect to the RRC radio unit via a browser interface from either the remote

Re: [Elecraft] K3/0 control not working with DXLap or N1MM

I'm going to bring the control setup to the radio site when I head up there and work it out on the LAN. I'm starting to think the K3/0 is broke. Would anyone using the K3/0 with control s/w like to share their K3/0 config settings? Also maybe I'm having a senior moment, I do connect the K3/0

Re: [Elecraft] K3/0 control not working with DXLap or N1MM

I don't actually have a K3/0-mini (I have the full-size K3/0), but I do believe that you should be able to connect to it with the K3 Utility - that's how you would update its firmware. It may be that something has failed inside he K3/0-mini ... or something software in Windows regarding COM

[Elecraft] K3/0 control not working with DXLap or N1MM

I just got back down here where the K3/0 is located. So Iain, your saying I should be able to talk to the K3/0 with the K3 utility at the control site? I just tried it and no, it doesn't see it on either of the two defined comports. I even brought a second USB cable to use between the laptop and

Re: [Elecraft] PX3: Possible problem with display

David Thanks for all the info. Wayne seems to have explained it fairly well. I think there were a few contributing factors in my setup. I have a new and quite a bit quieter antenna, thus less noise to cover up the small spikes. I never had the NB on but I had the PRE AMP off on 20M. Most of

Re: [Elecraft] PX3: Possible problem with display

I am pretty sure they are internally generated, plus they move with the cursor. They are mirrored above and below the cursor. I ran everything on batteries and took it for a walk outside. No change in signals. The S1-2 spikes aren't bad as band noise will mostly cover them, it is the S4 spikes

[Elecraft] Fwd: [KX3] 2017 ARRL Rocky Mtn Convention

-- Forwarded message -- From: "N7WY-BobR n...@rocketmail.com [KX3]" Date: Sep 9, 2016 11:43 Subject: [KX3] 2017 ARRL Rocky Mtn Convention To: Cc: Hi, The subject activity is May 27th in Cody, WY. One of the themes is

Re: [Elecraft] PX3: Possible problem with display

Further, I found this reply from Wayne (back in 2014) On Oct 14, 2014, at 6:35 AM, jsdroyster at nc.rr.com wrote: > Our panadapter regularly (but not always) shows wide green bands of "noise" before the antenna is connected. When present, the bands are visible in the same panadapter screen

Re: [Elecraft] PX3: Possible problem with display

You will get spikes with no antenna where they are not covered up by band noise. Also if you have a really big spike near where you are tuning, try turning down the NB level in THE PX3 or turn the PX3 NB OFF. Elecraft have explained about these spikes which are as a result of the switched mode

Re: [Elecraft] PX3: Possible problem with display

HiSince you are finding that the peaks diminish when the cables are removed it would seem that the cables are picking up signals from your environment. What happens if everything in your house is turned off except for the px3?I know my p3 will show fixed peaks that don't change with tuning if  

[Elecraft] PX3: Possible problem with display

Larry, Read the PX3 OSB null procedure carefully. Check/do the following: 1) Clean the cable connectors contact area with alcohol applied to a clean cloth, removing oil, grease, dirt, ect. Cleaning the connector in the KX3/PX3 is more of an issue, and I haven’t found a good way to clean

Re: [Elecraft] PX3: Possible problem with display

Don Thanks for the suggestion but that does not fix/improve the situation. Looking at it further I also have spikes at roughly 23, 30 and 52Khz above and below my cursor. The 52 Khz signal is at S4 the other two are about S2. I can turn on the PX3 and look at the display with no antenna

Re: [Elecraft] CW Monitor audio lost on Line Out after upgrade of FW release in my K3

I believe this is corrected in the latest field-test firmware release (5.53) which I'll send you. 73, Wayne N6KR On Sep 8, 2016, at 8:34 AM, Classe Bergman wrote: > Hi, > Today I upgraded my K3 with new FW, I was using 5.38/2.86 and I installed > 5.50/2.87 > I then

[Elecraft] How to disable the BYPASS switch

Hi, I've set up my K3 as a remote opened as a receiver - no transmit to all but a few selected hams. Recently I've discovered that someone has left the KAT500 in the BYPASS mode, which is telling me to "tighten" up the setup. I would like to disable BYPASS switch like I did with the ANT 3

Re: [Elecraft] PX3: Possible problem with display

Larry, I suspect hum, buzz, and noise pickup on the RX I/Q cable shield between the KX3 and the PX3. Try "Bonding" - run a heavy wire or strap between the KX3 and the PX3 in parallel with the RX I/Q cable. The shield from old RG-8 coax works well. 73, Don W3FPR On 9/9/2016 10:12 AM, Larry

[Elecraft] PX3: Possible problem with display

I have just recently noticed that there is a continual spike that follows my cursor. It is internally generated. In CW mode it is away from my tuned signal by the amount of my CW side tone setting and can be switched to above or below the cursor depending on if I am in CW or CW-R. These spikes

Re: [Elecraft] genovation keypad

On Fri, 2016-09-09 at 08:04 -0400, Bill wrote: > I have a Genovation 48 key keypad up and running - has been in use for > several months. With the exception of on/off, I do not have much need > to reach for the K3. Uses the P3 macro memories and is not directly  > connected to the K3. Bill, It

Re: [Elecraft] genovation keypad

I have a Genovation 48 key keypad up and running - has been in use for several months. With the exception of on/off, I do not have much need to reach for the K3. Uses the P3 macro memories and is not directly connected to the K3. Prior to that time I was using a PigKnob - a very practical