...and the first thing to check is that one of them hasn't come unplugged!
73,
Victor, 4X6GP
Rehovot, Israel
Formerly K2VCO
CWops no. 5
http://www.qsl.net/k2vco/
On 27/01/2020 6:38, Nr4c wrote:
> Download the K3 Assembly Manual. I believe they just plug in.
>
> Sent from my iPhone
> ...nr4c. bil
Download the K3 Assembly Manual. I believe they just plug in.
Sent from my iPhone
...nr4c. bill
> On Jan 26, 2020, at 10:50 PM, Gary K9GS wrote:
>
> Hello Don,How difficult is it to replace the encoders? Is there a document
> that describes the procedure?73,Gary K9GS
> Original me
Congratulations!
I second that emotion. I built mine 15 years ago--most fun building
project ever! More fun than an HW-101. More fun than an HW-16. Way more
fun than a Twoer. May the QSO-eating grin never fade.
73 Eric WD6DBM
On Sun, Jan 26, 2020, 12:32 PM Mark Yergin wrote:
> I’m proud
Hello Don,How difficult is it to replace the encoders? Is there a document
that describes the procedure?73,Gary K9GS
Original message From: Don Wilhelm
Date: 1/26/20 8:15 PM (GMT-06:00) To: Gary K9GS ,
Elecraft@mailman.qth.net Subject: Re: [Elecraft] VFO B dead Gary,If you a
Good Evening,
It was early one July day in Wisconsin, the sun would be up soon.
Pack mule Kevin was carrying Dad's target rifle of the day on one
shoulder, the rifle he was tuning on the other, forty pounds of .30 cal
ammunition in one hand and the target scopes in the other. I was
sinkin
Gary,
If you are not afraid of disassembling your K3, remove the Front Panel
assembly and swap the encoder A with encoder B. If the problem follows
the encoder, then order a new encoder from Elecraft. If that is not the
problem, contact supp...@elecraft.com for additional checks.
73,
Don W
W1NGA Al CO K3 5765 Al checked in via the internet as he was
not able to join us. In fact Al joined us for the last two weeks via the
internet.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/
Here is the list of stations checking in to the net today. Propagation was very
difficult today. A big thank you to Jim KO5V for his help relaying stations
that I could not hear. We meet at 14.303.5 on Sundays at 1800Z and everyone is
welcome to join in.
Elecraft SSB Net 1-26-2020
WB9JNZ
MY KAT3 has a problem. I am looking for a KANT3 board.
73, Paul W4PFM
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list h
Nearly unused, serial number 1451. Antenna tuner model, power wire and kx3
cable included. Couple scratches on bottom, sat on shelf for years unused.
950 dollars, ground shipping to lower 48 included. Contact me directly -
Foster2 at gmail dot com, PayPal or Apple Pay.
Foster
N3jku
___
One characteristic of the KUSB from Elecraft is that its jack screws can firmly
attach the cable to the K3. Not all USB to Serial adapters have this “gender”.
I find some USB adapters on Amazon with jack screws and others with nuts to
attach to screws. If you use a cable with jack nuts, it may n
Is anyone using the Bose 700 headphones with their K3? How are they
working? Are you using the wired audio cable? Does the audio cable give
the ability to connect both the microphone and the headset? Thanks,
- 73, John, N0TA
__
Elecra
FWIW .. he's looking for a K3 cable .. DX Engineering only carries the
KXUSB cable for the KX3.
Neil KN3ILZ
On 1/25/2020 7:00 PM, Dave wrote:
I ordered my KXUSB-A cable from DX Engineering. Closer to me, faster shipping.
I see you have a 6 area call. If you are in CA then ordering from Elecraf
I just had my K3 in for service and a checkup. I REALLY hope I can avoid
sending it in again. The VFO B knob is completely dead. Turning it does not
tune VFO B. Also tried the config screen...same thing.I suspect the encoder is
bad but it showed no symptoms prior..otherwise I would have had i
I have used USB to Serial adapters made by FTDI, itself, for years. These
are of the highest quality. I have also used, successfully, Sabrent and
others including ones with multiple ports using their chip. You can
purchase sub-assemblies and complete cables directly from FTDI through
their USA or
On Sun, Jan 26, 2020, at 16:10, Phil Kane wrote:
> Now I need to replace my keystroke-controlled 2-pole KVM switch that
> uses VGA display ports with one that will handle DVI or Mini-Display
> ports as well as keyboard and mouse USB ports. Any suggestions?
I've had good luck with KVMs from StarTe
Hi:
Has anyone tried using one of the CNC Weighted Tuning Knobs on their
KPod. I rarely use the Main VFO on my K3S and thinking of moving the
aftermarket CNC knob to the Kpod. Good or bad would like to hear your
experience or recommendations.
--
*73 De Mike*
*VE3YF
_/http://www.ve3yf.com/_
On 1/25/2020 6:55 PM, Don Wilhelm wrote:
> I can also recommend the Edgeport USB to serial converters.
I too use an Edgeport-8 in connection with my K2 and accessories (TNC,
RigBlaster, etc.). It has been super-reliable.
Now I need to replace my keystroke-controlled 2-pole KVM switch that
uses
I’m proud to report that K2 #7867 is on the air! Just completed my first
QSO with Albert, K3AAR, on 40M CW running 5W into an EFHW. Al responded to
my second CQ. I started building in February of 2019, took most of the
summer and fall off, then finished it up over the last few weeks.
Thanks to
Wayn3:
Sounds like you had a great time.
In addition to having more time outdoors, more chance to "re-wild" amateur
radio it also give you more time to spend with you son. Those times are the
most important because they are fleeting and once gone are unrecoverable.
73
Marv
-Original Message
My son and I hiked a few miles into Henry Coe state park yesterday, setting up
a winter FD station (KX2) at a spot overlooking an idyllic pond full of
bullfrogs. The weather was, ironically, just about perfect: 60 F, no wind, blue
skies. I regret that we weren't able to share the pain of those w
21 matches
Mail list logo