In my professional work before I retired in 2009, I used N-connectors
as much as possible. Some commercial VHF marine radios and the CB
radios (required on our boats) had UHF connectors so I bought
Amphenol PL-259's for them. I bought antennas that had N connectors.
Sealing on boats I used
Hello Elecrafters,
I have a Nue-PSK modem surplus to my requirement and available for sale. It
was returned to the factory for upgrade and installation of USB + RTCC card in
May 2013 so that the modem is now like new and with the latest software and
hardware.
Nue-Psk modem will
I ran Norton Antivirus several years ago on win2000pro but switched
to AVG on all but two of my computers. I have an old win95 laptop
that never goes on-line and another backup computer which I run ESET antivirus.
MalewareBytes is the only software that catches all the bad stuff. I
run a
Hello,
I have the problem, that the K3 sends continously the frequencies of
VFO a and VFO B (FAxxx, FB) out. This results, that the
Logging-Program always shows me both frequencies.
I was looking around, how I can have just the main VFO in the
seriel-Output, but haven't
I use the Eneloop XX 2500 and am very pleased. The internal charger charges
then just fine. Can't comment on the power supply. I use the Gamma
Research HPS-1A which is overkill for only 12 watts but it will also power
my K3 at 100 watts and KX3 with the 100 watt amp when I get one. It is
Karl-Heinz == Karl-Heinz Kuehlborn khkuehlb...@outlook.com writes:
Karl-Heinz Hello,
Karl-Heinz I have the problem, that the K3 sends continously the
frequencies of
Karl-Heinz VFO a and VFO B (FAxxx, FB) out. This results,
that the
Karl-Heinz Logging-Program
Hi gang
I have a very strange condition with my K3. Absolutely no reception in CW mode
on any band. There is dead quiet, no noise no static. It looks as though I can
xmit CW, as the red LED lights.
All other modes are working normally
Thoughts? Suggestions?
73 NU4C
Verify Roofing filter(s) configured for CW RX?
-Bruce N1RX
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted
I have a new k3-k3/0 twin setup going. When I have the k3/0 paired up with
the k3 neither can decode digital modes. I assume that's the state of
affairs right now. Any plans to include native support for digital in the
k3/0?
--
View this message in context:
After more testing, I see that, as stated previously, this is a display
problem. When in ssb mode and pressing PTT I am modulating the k3 even
though the k3/0 diplays cw mode.
--
View this message in context:
Looking for the KXPD3 paddles for the KX3. Anyone have one
to part with? Thanks, Mike K0AZ
K0AZ
Mike Sanders
EM37cd SW Missouri
www.k0az.com
__
Elecraft mailing list
Home:
On 11/9/2013 2:46 PM, Igor Sokolov wrote:
I always thought of Beverage as directional antenna that favors low
angles. Is it not so?
Beverages tend to favor higher wave angles, while verticals favor low
angles. Those who have lots of land like to install both Beverages and
vertical RX
I have a K3/P3(w/SVGA) connected to DXLabs Commander and the P3 display
hangs from time to time. By hang, I mean it just freezes for a second
or two periodically then starts working again by itself, I do not have
to do anything to restart it.
It seems to be connected to Commanders polling the K3
What software?
I use DX Labs and don't have this problem. I suspect that if I run split, it
might spot both frequencies.
More info please.
...bill nr4c
Sent from my Verizon Wireless 4G LTE DROID
Karl-Heinz Kuehlborn khkuehlb...@outlook.com wrote:
Hello,
I have the problem, that the K3
Hi,
today i was in QSO in 17 meter band CW when my power supply (switching from
Nissei model MS 280A) has shut down (i was in tx with 100 watt). After i
discover that the supply is death.. and also my K3 (#4777) now it's death
also..connected to a battery it's not swithing ON... nothing...
any
Did you confirm cable and fuses are good?
73,
Rick wa6nhc
Tiny iPhone 5 keypad, typos are inevitable
On Nov 10, 2013, at 9:17 AM, Andrea Borgnino a.borgn...@gmail.com wrote:
Hi,
today i was in QSO in 17 meter band CW when my power supply (switching from
Nissei model MS 280A) has shut down
Since the addition of the ATU to my KX1, and the fact that when operating
portable I use an EFHW antenna fed directly with no feed line, I've been
wanting to install a set of binding posts to eliminate the need for a BNC
adapter. Anyone who's built a KX1 knows that it's a very tight fit inside
All fuses good?
Sent from my Verizon Wireless 4G LTE DROID
Andrea Borgnino a.borgn...@gmail.com wrote:
Hi,
today i was in QSO in 17 meter band CW when my power supply (switching from
Nissei model MS 280A) has shut down (i was in tx with 100 watt). After i
discover that the supply is death..
yes cable it's good, there was no fuse on cable from K3 to the supply.
I just check the K3 with a battery and it's seem that the K3 it's in short
circuit.. the battery voltage go to 12v to 0.5v when connected to the K3..
can be the fuse inside the K3 ??
On Sun, Nov 10, 2013 at 7:19 PM, Rick
73
John WD1V
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support
Definitely useful in at least two places.
Low bands CW and RTTY. Maybe SSB too altho I don't use SSB much, no
data. Lot of effort to install a good directional antenna on 160/80,
every advantage helps. Diversity has played a significant role in my
lowband operations. My diversity ant is a low
Perhaps before die, the 280A delivered an overvoltage output. That could
explain both the death of the 280A and the short of the K3.
Obviously, I hope to be wrong
Massimo I0MCF
Il 10/11/2013 20:06, Andrea Borgnino ha scritto:
yes cable it's good, there was no fuse on cable from K3
Hi all,
I'm looking for volunteers to test a few K3 firmware changes. See release notes
below. If you'd like to try this firmware ahead of the next beta release,
please email me directly.
73,
Wayne
N6KR
* * *
K3 MCU 4.72 / DSP 2.82, Nov. 10, 2013
* RIT CAN NOW BE TURNED ON/OFF DURING
Hi Paul,
Check your RX EQ settings.
73,
Mike K2MK
Paul Milward wrote
Hi gang
I have a very strange condition with my K3. Absolutely no reception in CW
mode on any band. There is dead quiet, no noise no static. It looks as
though I can xmit CW, as the red LED lights.
All other modes are
I'm now the proud owner of a KX3 and for the most part have everything setup
and working. The one thing I can't get to work currently is the CW (and likely
RTTY and PSK) decode.
Now the antenna setup I have is not great and I'm suffering from high levels of
RF interference. Thus, it's
Hi Gary,
Let's get the obvious questions out of the way 1st...
1. You have pressed the DATA button in for more than about 1 second and
moved the setting to 'RX THR1' through to 'RX THR9' ?
2. Have you tried the various different settings of THRnumber ?
3. Do you have the preamp on? I find
I need some tutelage on Com Ports. The K3 and P3 both use Com Port 6 for access
to the computer. Com Port 6 is also used but the HRD/DM780/USB Navigator and
MMTTY. This is not a real problem as I do not use all these programs at the
same time. However, it would be nice to be able to access the
Pristine condition KX3-K, #4429, assembled June, 2013. Includes KXFL3
roofing filter, MH3 hand mic, KX3-PCKT cable set, Fred Cady manual,
Side-KX side plates and lexan cover, original manuals and boxes. Latest
firmware. Selling as a complete package for $1175 shipped/insured CONUS.
Also
On the K2 Front Panel Display I put the led back screen through the holes of
the spacers. The LCD is already installed over the LED. Couple steps later
realized your supposed to take them out. I checked with meter and there not
shorting anything out. All resistance checks at the end are good
John,
If I understand you correctly, you are OK.
There were some backlight LED assemblies that had short leads, and they
had to be soldered from the component side (in that case, the spacers
would prevent soldering). If you put the spacers over the LED leads and
were able to solder them from
It must be me or this would drive everyone nuts. During the WAE rtty contest,
while sending
QTCs ( lengthy transmission ) about 1 time in 10, the k3 would lock up and
display the ERR DSE
message. I run so2r and it happened on both rigs. I would power the affected
k3 off and back
on and try
Bill,
You may wish to visit my website and check the How To section as I have
documented how I use my K3 and five different software programs all at the
same time with a single serial or USB port - the necessary software is
LP_Bridge, which is free - based on its value, I suggest once you get it
When my W2 is set to trip, or interrupt the PTT line, when the SWR rises above
a preset level, the manual says to push the sensor or range button to reset the
W2 and re-enable the PTT line. Problem is, I have to push the sensor or range
buttons multiple times, usually four, to get the W2 to
I'm looking for anyone that may have extra k2 parts. In the process of building
one by parts bags. But I need some oddball items. The encoder. The acryllic
lens for the front panel. Any uneeded stand offs chassis screws and 2d
fasteners. The side panels from unused blank enclosure? Tilt
Bill:
There are port sharing programs, such as LP-Bridge, that permit multiple
programs to share the K3's single COM port. What these programs do is stand
in for the K3. The port sharing owns the K3's single serial port, and the
port sharing program provides virtual ports that your other
Sent from my iPhone this time well the first thing I have to say is the cake
street is the most amazing piece of amateur radio equipment I have ever played
with Ima blind guy and I use ham pod to read the menus while in one of the
menus I somehow disabled the antenna tuner and now when I go
Thanks for the feedback. I will follow-up on the suggestions.
73,
Bill W0BBI
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-Com-Port-Question-tp7580665p7580675.html
Sent from the Elecraft mailing list archive at Nabble.com.
37 matches
Mail list logo
