The K3 build went nicely, no errors; same for the P3. Now just built
Winkey usb smt to go with N1MM+ to add to the station for contesting.
The keyer kit itself is working just fine as standalone keyer into K3.
However, I'm finding the documentation for integrating N1MM+ the my Dell
system
Mike,
I am using it with 2 loops, which are mounted at a 90 degree angle with
respect to eachother. This allows me to switch direction, which is most
pronounced on 160m and medium wave. The loops themselves are square rather
than round (as recommended by LZ1AQ) due to mechanical constraints,
Consulting Vol XLIX of my station notebook:
In the menus at the top of the Entry Window, go to Config.Configure
Ports etc.
-- In Hardware tab:
-- In the first line, select the COM port for the K3 CAT connection
-- Select Elecraft K3 from the Radio drop down list
-- Leave Digi and CW/Other
On Mon,2/2/2015 1:47 PM, Phil Anderson wrote:
However, I'm finding the documentation for integrating N1MM+ the my
Dell system 7.0 and keyer with the K3/P3 a bit much.
The N1MM+ install is pretty straightforward, and usually goes pretty
easily. You must first do the basic install, then reboot
While doing some rework, a hot lead fell out of my hand and dropped on the
board. A few segments on the display lit up briefly and then an eerie
silence. Except for the little map light, nothing works. I've checked the
DC voltages on the IC's and voltage regulators and the only voltages I can
I have a Tascam US-322 Audio Interface that works well with my K3 and desktop
computer. I have tried to use it with my laptops for portable ops but they
do not have enough power to run the interface. Is there a way to power the
interface apart from the usual USB computer connection? I would also
Great group! I'd like the readers of this reflector to know that I received
several replies to my post, with 12 pictures, and most impressive; three others
volunteered to remove the case from their tuners to photograph the coils for
me. That is a tedious job.
K3KO suggested that some
I have calibrated the S-Meter on HF but on 2-meters (via the internal
transverter) the S-Meters reads high.
I have looked through the manual and the menu settings and I'm unable to locate
the setting to adjust the S-Meter for 2 Meters.
Can someone point me to the correct place.
Thank you
We bought a short lo-band E-field whip with pre-amp from Clifton Labs a few
months ago, and two circular antennas a few weeks ago.
All are well-built and the whip has performed well; it feeds the VE7AB RBN
node.
The circular antennas are still being tested.
Eric VA7DZ
__
Eric
Decided to try the latest beta P3 firmware. All loaded including FPGA.
SVGA output is frozen and P3 is updating very slowly.
When I turn the SVGA display enable off the P3 behaves normally with a
proper update rate.
I've removed power from the P3 completely and restarted it with no
improvement.
This morning I noticed something strange with #3539. On 80 160, tune only put
out 10W. The level is set for 44W. Full output is 44W, power set to 100W. SWR
with the AT in bypass is 1.3 on 80M, 1.2 on 160M. All this on ANT1. Power out
on 40M up is as expected.
I connected a dummy load to
I did a poor job on describing the noise level jump. If I switch to ANT2, the
2nd rec. level goes WAAAY up.
73, Mike NF4L
On Feb 2, 2015, at 7:38 AM, Mike Reublin NF4L n...@comcast.net wrote:
This morning I noticed something strange with #3539. On 80 160, tune only
put out 10W. The level
A TX cal seems to have taken care of the power issue.
Mike NF4L
On Feb 2, 2015, at 8:09 AM, Mike Reublin NF4L n...@comcast.net wrote:
I did a poor job on describing the noise level jump. If I switch to ANT2, the
2nd rec. level goes WAAAY up.
73, Mike NF4L
On Feb 2, 2015, at 7:38 AM,
On Sun,2/1/2015 10:15 PM, Vic Rosenthal wrote:
Lots of room on your desk, Hank?
I've seen Hank's setup. Not on his desk, but nicely done.
73, Jim K9YC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Yes, I noticed the Step Span on mine seemed to reset after a power
cycle. It also appears to be set on a per band basis. Is there is a
way to set the REF LVL on a per band basis as well?
Mike
KI0HA
On 2/2/2015 04:31, ANDY NEHAN wrote:
I have noticed that the Span Step function (which I
I have noticed that the Span Step function (which I like) is not sticky - in
that every time I recycle my radio the feature, if set, is lost. That means I
have to go into the menu and reset it. Surely it would be better if the feature
was sticky like the other features??
What do you think PaulS
Yes, it always helps to read the manual! Even for the coffeemaker -
they *used* to be so simple.
73,
Don W3FPR
On 2/2/2015 11:16 PM, KK5IB wrote:
Thanks for suggestions. Problem was that the software and drivers had to be
installed before connecting the interface. Found that out by reading
Clark,
U1 pin 7 is the VSMTR signal and the voltage source comes from the
product detector U5 pin 2.
Either the product detector is damaged or U1 pin 7 has a shorted input.
To check which, remove U1 and bend pin 7 out a bit, then plug it back
into the socket with pin 7 hanging on the
Thanks, Don. I'm ordering U1 and U5.
The display is completely dead--no segments. I also see I erred in
reporting that all other voltages were ok. U5 pins 1 2 measured 0.0.
Don't know how I missed that but it makes sense as the receiver is dead.
Clark/WU4B
On Mon, Feb 2, 2015 at 9:40 PM,
On Mon,2/2/2015 3:58 PM, KK5IB wrote:
I have tried to use it with my laptops for portable ops but they
do not have enough power to run the interface. Is there a way to power the
interface apart from the usual USB computer connection?
Two suggestions. First, try a different port on the
Thanks for suggestions. Problem was that the software and drivers had to be
installed before connecting the interface. Found that out by reading the
manual. Works fine now.
Darryl, KK5IB
--
View this message in context:
GOOGLE dendrites plagued GE's MASTR 2-way line for many years.
73
Ken - K0PP
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Andy Mike,
The Step Span in not remembered through a power cycle on my P3.
I have different REF LVL adjustments for each band on my P3 and they stay
that way through band changes and through power cycles.
I power my P3 from the K3 and I do not use the P3 power button. Could that
be a factor
I could not use the latest beta either. I had to go one beta back.
Gerald KC6CNN
On Feb 2, 2015 7:46 PM, Jim Miller j...@jtmiller.com wrote:
Decided to try the latest beta P3 firmware. All loaded including FPGA.
SVGA output is frozen and P3 is updating very slowly.
When I turn the SVGA
The #navassa https://twitter.com/search?q=%23navassa K1N Dxpedition is now on
the air using our K3s and KPA500s! See:
http://www.dxsummit.fi/#/?dx_calls=K1N and
http://www.navassadx.com/
73,
Eric
elecraft.com
__
Elecraft mailing list
Thanks, Jim, that's opened out the discussion very well for me. I am not
able to determine how bad this makes the performance, since the output is
floating and I think hardly susceptible to common mode problems. I'm in the
market for such antennas but most are outside my budget. I would like
I just checked on a newly upgraded P3/SVGA and stepped span is remembered
through a power cycle. (I also checked the code just to be sure). If I turn
on stepped span and then power cycle the unit and press the SPAN key, the
span is in stepped mode. If I press a key that I assigned to stepped
David,
Not sure what ur budget is.
The amp in the Pixel is a Cliffton Labs design, using the Norton architecture.
Jack of Cliffton labs cannot share info of the amp design, as he is under
non-disclosure. He does sell a great amp, using the Norton structure, that has
a gain ~ 50% of the
For sale:
ORIGINAL SideKX ULTIMATE Combination kit for KX3 and PX3: KX3 Endpannels and
Lexan Cover, PX3 Endpannels and Lexan Cover furthermore the KXPD Cover. The Kit
is new! Fixed Price: 175€ plus shipping (ships from Germany), payment
exclusively via PayPal. More Information under:
29 matches
Mail list logo
