Hi Tom,
I have travelled to Italy on two occasions by plane with my KX3. I
will be going to IT9 land later this autumn.
Take your license with you. I always take my original license not a
copy. Have your passport but whilst travelling around in Italy/Europe keep
your passport in
Tom,
Besides what I wrote previously you might go to the A.R.I Italian ARRL
website and print out their instructions for reciprocal operation in Italy.
Your prefix will change depending on where you are operating from in Italy.
It is also handy to have this even if in English in your
CEPT is pretty easy, see http://www.arrl.org/us-amateurs-operating-overseas
73, Ian N8IK
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Doug
Turnbull
Sent: Saturday, August 29, 2015 03:36
To: 'Tom Morehouse' k4...@me.com;
Mille grazie- Thanks to all who responded. Good advice - I think I have
everything necessary - and hope to see you on the air!
A week in Piemonte and a week in Umbria with wonderful people, food, wine and
ham radio!
73
Tom
K4AEN
Any word yet on the audio NF of the K3IOB?
Does the K3IOB output a stereo signal for use with the second receiver?
Thanks,
Joel - W4JBB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Good morning,
I have a new K3S, serial # 10195. All was going well until I hooked up
my KPA500 to the K3S using the Elecraft supplied aux cable (E850463).
In standby mode (on the KPA500) the audio level on the K3S is nice and
loud, BUT when I press the OPER button on the KPA500 the audio
Perhaps your KPA500 key line is being pulled low? Might be a cable issue.
I think there's an asterisk on the left side of the KPA500 LCD that shows
when the PA KEY line is being pulled down.
73 de Dick, K6KR
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On
Hi Ken,
First make sure the cables between the PX3 and the KX3 are firmly plugged in
on both the KX3 and PX3 sides. Pay attention to the I/Q 2.5mm cable.
During adjustment, move the encoder slowly, the adjustment values are
usually small.
If you're still having trouble, please contact
My take on this.a fellow can't have too many radios.
73
Bob, K4TAX
K3S s/n 10,163
On 8/28/2015 7:39 PM, Jim Rogers wrote:
I just got my UPS tracking number and my new K3s will arrive on
Wednsday. So now the decision of whether to keep my K3 100 as a
backup or sell it.
It is s/n
Don,
Of course it wouldn't in RX. Excuse me. I was under the impression
that the OP was referring to TX and the TX audio, so I'll stand on my
comment. Just trying to help sort it out. The OP didn't specifically
state RX or TX so how do you *really* know?
Warren
On 8/29/2015 4:35 PM, Don
Warren,
His problem was in receive, not transmit. So I don't understand how the
drive level setting could have anything to do with it.
73,
Don W3FPR
On 8/29/2015 3:52 PM, Warren Merkel wrote:
Jim,
Did you check what the K3S power level displays when the KPA500 is in
Operate mode? It
Have the units been moved? Updated? Disconnected/reconnected since working?
If so: Please power off the amp and rig. Pull the cable and check for
pushed/bent pins.
Just a shot in the dark.
Sent from Mail for Windows 10
From: Dick Dievendorff
Sent: Saturday, August 29, 2015 12:20 PM
To:
All,
This week's Elecraft SSB Net will meet tomorrow, 30 August, at 18:00 UTC on
14.3035 +/-. I will be net control from my QTH in Roswell, GA, just north
of Atlanta. Hopefully, the bands will be nicer this week than they have in
the past few weeks. I look forward to hearing everyone on the net.
Jim,
Did you check what the K3S power level displays when the KPA500 is in
Operate mode? It could be set for very low drive. I have mine set up to
lower the drive from 100w to 30w when the KPA500 goes from standby to
operate. If you have the setting for per band mode enabled, you will
need to
First of all, I want to thank Elecraft for making such a fine rig!
With the exception of my first activation (was still waiting for my KX3 to
arrive back in May 2012), 99.99% of my SOTA Goat was achieved using the KX3.
It really shined today as the peak that was to make the 1000th point was
Jim;
Dick’s advice is sound. When in OPER mode, the KPA will display an asterisk on
the left side of the display when PTT is applied. If you are seeing that
indicator, check the PTT connections to see if there is a short to ground. When
using the KPA with your K3S, you should only use the AUX
You should take a copy of your purchase receipt with you. That way it won't be
questioned when you come home. I've never had a problem but I always carry the
receipts for high value camera equipment.
Have a great trip!
73,
Brian, K0DTJ
17 matches
Mail list logo
