Using a 100W light bulb will not provide the required impedance, and will
produce inaccurate results and possible damage the transceiver.
True, also - In the old days there was no need to specify *incandescent*
light bulb. Wonder what would happen with a CFL or LED lamp (do not try
this)?
The
In my younger years I thought of the FCC of a regulatory and technology
body. My thinking changed when UPS successfully lobbied the FCC in 1989 to
reallocate part of 220MHz from Amateur to Commercial service.
UPS argued that the reallocation was in the public interest and they would
put the
*Netflix* got what they wanted. They had better lobbyists and took a
dispute between them and Comcast, expanded the scope to include the entire
internet, and then got the .gov on their side.
73,
K3LL/6
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On
Hi,
Would it be possible to allow the ability to show temperature in degrees F
or C in the next firmware update?
Thanks,
Cliff K3LL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Antenna issues specific to the OP aside, there is a valid reason to have the
KAT500 recognize split and inhibit retuning/recall.
The need for this functionality is very apparent when running split on 40m
SSB when the DX is below 7.1 MHz and listening up much higher than 5KHz for
anyone using a
level similarities, but not really.
Do you know how the KAT500 interprets frequency, if driving only the band
data lines (BAND0-3) via an external TTL device? Does it pick middle of the
band if there is no last used frequency?
73,
Cliff K3LL
-Original Message-
From: Cliff Frescura
PM
To: Cliff Frescura; Elecraft@mailman.qth.net
Subject: Re: [Elecraft] KAT500 Re-Tuning
Are you asking for the KAT500 to choose two different tuning solutions when
operating split? At present it chooses the VFO B frequency for its solution
according to:
MCU 4.83 / DSP 2.82, 2-8-2014
* FSK-D
Sounds fine here.
Cliff K3LL
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of
Chester Alderman
Sent: Friday, November 06, 2015 1:43 PM
To: 'Steve Ellington'; elecraft@mailman.qth.net
Subject: Re: [Elecraft] Speaker SP3 Video
No audio on your
S-232 line where DXLabs will send data via
the Secondary COM Port (K3 native format) to the KAT500 when clicking on a spot
or moving the Kenwood VFO. Alas, I have the USB cable for the KAT500, so I
need to get the RS-232 cable.
73,
Cliff K3LL/6
-Original Message-----
From: Cliff Frescura
I would start with your local AM Broadcast stations like WBT on 1100 KHz. I
would then check out WWV on 5.0MHz, 10MHz, 15MHz, 20MHz as well as CHU in
Canada on 3.33MHz, 7.850MHz and 14.67MHz. You might want to add these into
memory for easy recall.
Be mindful that time of day/current
[mailto:jackbrin...@me.com]
Sent: Friday, October 09, 2015 12:55 PM
To: Cliff Frescura
Cc: Elecraft Reflector
Subject: Re: [Elecraft] [KAT500] PC Data to Amp Control?
Or connect the Kenwood’s serial port to the KPA500’s Radio port, then set the
RADIO = SERIAL in the KPA.
Follow the directions
Hi,
If I change bands on the KAT500 via the PC Data port, it appears that the
new band data is not sent to the Amp Control connector. Is this expected
behavior? (hoping no).
For reference, my setup is:
Kenwood TS-940
DXLabs Logging program
KAT500
KPA500
The 940 is connected to
]
Sent: Friday, October 09, 2015 10:55 AM
To: Cliff Frescura
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] [KAT500] PC Data to Amp Control?
The KAT500 can read, but not pull down the 4 band change lines.
Dick, K6KR
Sent from my iPhone
> On Oct 8, 2015, at 21:07, Cliff Frescura
: Monday, November 16, 2015 9:36 PM
To: Cliff Frescura
Cc: Cady, Fred; Elecraft@mailman.qth.net
Subject: Re: [Elecraft] KAT500 Re-Tuning
If the band lines are used only, the ATU picks a mid band freq if there is
no history since last ATU power up. On first tx after that, it performs a
memory recall
+1000
And does this rig have the CAT fix for split?
Original message From: Tony Estep
Date:09/02/2015 5:48 PM (GMT-08:00)
To: Elecraft Reflector
Subject: Re: [Elecraft] Icom IC-7300
I note that it has only one tuning knob,
ails
Did the boys at HamCon quote a price for the speaker?
73,
Brian, W6FVI
On 9/14/2015 11:51 AM, Cliff Frescura wrote:
> I don't know where it is made, but I was able to see one in the flesh
> at HamCon this past weekend and it has a solid feel and weight to it
> (in addition to sound
Maybe the dummy load could be an option for the speaker /s
73,
Cliff K3LL
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Fred
Jensen
Sent: Thursday, September 17, 2015 7:36 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Product
I don't know where it is made, but I was able to see one in the flesh at
HamCon this past weekend and it has a solid feel and weight to it (in
addition to sounding great too). Seems like a no brainer addition to me.
One wish would be to have the headphone jack on the speaker and use the
input
Don't discount the possibility that someone hijacked his call sign -
especially if funds were not mailed to his physical address.
Cliff K3LL/6
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of David
Gilbert
Sent: Tuesday, September 22, 2015 1:20 PM
I agree with N1MGO,
I've come full circle on this one and am in the process of removing all of
the USB/RS-232 converters in my setup and reinstalling a 4 port card that I
had in an old XP system (drivers work fine).
Determining what is a quality USB/RS-232 serial adapter is not always clear.
8 ft is not true for rs-232. Depends on type of cable and baud rate. 50ft is
generally fine and can go up to hundreds of feet. Maybe you are thinking about
usb.
73,
Cliff K3LL
Original message From: Mike va3mw
Date:12/30/2015 11:32 AM (GMT-08:00)
I find it hard to believe that the processor in the KPA is locked up. I've
done quite a bit of experimentation with the RS-232 port on it and have
never locked mine up and never had the need to attempt a reset?
Can you get to the menu of the KPA? If so, it is not locked up. However if
you
I find the scaling awkward as well. My W2 is placed on the input side of my
KPA500 and it seems that dividing the scale by two might do the trick. I've
not looked at the schematic, but wonder if it could be tricked by a resistor
divider in the sensor line.
73,
Cliff K3LL
-Original
Sounds like the amp is plugged into an outlet that is potentially overloaded
or underrated.
Changing the tap won't solve the problem and may damage the amp.
73,
Cliff K3LL
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Matt
Murphy
Sent: Friday,
.
Alan N1AL
On 11/20/2015 07:15 AM, Cliff Frescura wrote:
> I find the scaling awkward as well. My W2 is placed on the input side
> of my
> KPA500 and it seems that dividing the scale by two might do the trick.
> I've not looked at the schematic, but wonder if it could
Yes, check out:
http://www.dxlabsuite.com/commander/Help/CommandSequences.htm
Also, the DXLab reflector at dx...@yahoogroups.com is very active, much like
this one.
73,
Cliff K3LL/6
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jim -
N4ST
Hi Jerry,
In regard to:
"4) It should have support for contest operating."
Most general purpose logging programs have some contesting capabilities, but
there are many aspects of contesting that really necessitate the use of a
dedicated contest logging program.
I would suggest you start
Thanks,
I'm assuming there is a small copy/paste artifact on the page since it shows
the date of the earlier software version, 1.67.
73,
Cliff K3LL/6
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Dick
Dievendorff
Sent: Monday, June 13, 2016
My factory assembled KPA-500 was shipped in one carton, all parts installed.
Set the line voltage and install the fuses, and you're off to the races!
73,
Cliff K3LL/6
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Ralph
McClintock
Sent:
Antennas?
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Paul
VanOveren
Sent: Sunday, January 31, 2016 5:10 PM
To: elecraft reflector
Subject: [Elecraft] Love me K3 line
I have worked both S Sandwich and S. Georgia Islands on 4 bands and CW and
RS-232 use +3 to +15VDC and -3 to -15VDC for signaling levels, thus -5 and +5
will work too, but *not* 0VDC and +5VDC
Like others, I've run RS-232 over 100's of feet. RS-422 will go much further
and has the advantages of multi-drop and noise immunity due to its differential
nature.
73,
e
download.
--
David Woolley
Owner K2 06123
On 21/01/16 20:03, Cliff Frescura wrote:
> RS-232 use +3 to +15VDC and -3 to -15VDC for signaling levels, thus -5
> and +5 will work too, but *not* 0VDC and +5VDC
>
__
Elecraft mail
I have an old TS-940 working with the KPA500. I used the ACC amp
connections on the back on the Kenwood for PTT, which I believe is a DIP
mechanical relay - not loud at all. In addition, the KPA500 sniffs the
RS-232 line between the Kenwood and my logging PC running DXLabs to
automatically
Can you measure the 110V line voltage on key down? Is it stiff enough?
73,
Cliff K3LL/6
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Mike
Crownover
Sent: Tuesday, February 16, 2016 8:22 AM
To: 'Nr4c'
Cc: elecraft@mailman.qth.net
Subject: Re:
Yes, the signal has to travel ~22,300 miles x 2 (up and down).
73,
Cliff K3LL/6
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of David
Gilbert
Sent: Saturday, April 09, 2016 8:53 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Operating
Another test you can try is to short pins 2 and 3 on the RS-232 side of the
converter (loop back) and then use a terminal program to see if characters
that you type are echoed back.
Some notes:
1. make sure handshaking is off/none
2. make sure local echo is off
3. data rate does not matter
4.
I think I jumped the gun and was wrong.
73,
Cliff K3LL/6
-Original Message-
From: Dauer, Edward [mailto:eda...@law.du.edu]
Sent: Sunday, August 07, 2016 3:42 PM
To: Cliff Frescura; elecraft@mailman.qth.net; brian
Subject: Re: [Elecraft] KPA500 Band Tracking
Thanks, Cliff. I am aware
"But the KPA doesn’t track the K3’s band choice correctly."
...it's by design.
In the US the maximum power on 30m is 200W PEP.
http://www.arrl.org/frequency-allocations
73,
Cliff K3LL/6
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Dauer,
"Elecraft Inside!", to borrow Intel's old line.
But seriously, people just spent circa $3K-$4K USD (new) on a high
performance radio and then go this route on a fairly critical component?
On one hand, it's a tribute to Elecraft's success and popularity, on the
other it can be a support
Cable has sold.
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Cliff
Frescura
Sent: Saturday, April 22, 2017 11:00 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] FS: E850463 KAT500 to KPA500 Cable
Hi,
I have a KAT500 to KPA500 15 Pin
Hi,
I have a KAT500 to KPA500 15 Pin cable that is excess to my needs.
Complete info here: http://www.elecraft.com/elecraft_prod_list.htm#kat500
$20 via PayPal and shipped USPS Priority mail.
Thanks and 73,
Cliff K3LL/6
For sale:
KPA500 $1500
KAT500 $500
Factory built, original owner.
Plus shipping and insurance. I am located in Los Angeles and can meet
nearby.
Please reply off list c...@cfcorp.com
73,
Cliff K3LL/6
__
The KPA500 has been sold. The KAT500 is still available.
From: Cliff Frescura [mailto:c...@cfcorp.com]
Sent: Sunday, November 12, 2017 5:59 PM
To: 'elecraft@mailman.qth.net'
Subject: FS KPA500 and KAT500
For sale:
KPA500 $1500
KAT500 $500
Factory built, original owner
Yes, you can make a "sniffer" that sends data to the KPA500 from the radio.
This is exactly how I used my KPA500 with my TS-940.
73,
Cliff K3LL/6
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Paul Baldock
Sent: Monday,
A bit of trivia...
When the antenna/tower at KDKA was replaced in 1994, the legs of the old
antenna were cut into thin cross sections, encased in clear plastic with a
station medallion and sold for charity to Children's Hospital of Pittsburgh
during their annual Christmas Fundraiser. It's a
Being in the payments industry, I can tell you that most of these policies
are driven by the card brands (Visa, MasterCard, etc.), certifying bodies
(PCI, EMVCo) as well as the payment gateways. It is a very complicated
chain with many rules.
The shopping cart either does an immediate charge or
I have for sale:
1. W2 wattmeter with DCHF-2000 1.8 - 54 MHz 2KW coupler, coupler cable, and
power cable
(power pole end). Modified to turn on when power is applied: $285
2. DCV/U-200 144 MHz - 450 MHz 200W coupler with coupler cable (coupler only):
$90
W2 with both couplers : $350
Pictures
The DCV/U-200 has been sold. W2 with HF coupler still available.
Thanks,
Cliff K3LL/6
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Cliff
Frescura
Sent: Wednesday, September 16, 2020 8:47 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] FS W2 Wattmeter HF
48 matches
Mail list logo