Anyone know if the frequency counter mode of the MFJ-259B is accurate
enough to do the 4 MHz Oscillator Calibration of the K2?
Thanks
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must
I am currently building K2 6233.
Setting AGC Threshold - Manual states to turn R1 until pin 5 on U2
reads 3.8V. However, I can't get the voltage this high. When I turn
R1, the voltage range is from 3.75V to 2.638V.
Anyone have any ideas?
Thanks
--
JT Croteau, N1ESE - Manchester, NH
from a TV with no repairs
is pretty impressive.
I leave my computers on all the time but I probably use them more
frequently than most people.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must
On 8/22/07, sergio [EMAIL PROTECTED] wrote:
in building the k2, i found a spot for C75, but i don't see it
referenced in the doco anywhere..
Sergio,
On page 73 of the manual, there's an Uninstalled Components section.
C75 is listed here as C75 (synthesizer area); supplied with K160RX.
--
JT
chokes.
2 - Does the color of the body matter? RFC4, RFC5, RFC8, RFC9, and
RFC7 - Should all be green bodied but mine are tan bodied.
Thanks
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must
the chokes. I feel your pain.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman
Speaking of Speakers...
Anyone have experience with the Sounds Sweet Speaker? This was
supposedly designed for the purposes we are complaining about.
http://www.soundssweet.com/
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post
%20the%20K2.pdf
I've been thinking about building one.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
+ series of monoband rigs are much better
performers than these two. They have a 35-40 kHz VFO. Best bang for
the buck at $55 delivered.
http://www.smallwonderlabs.com/swl_swp.htm
Also check out the SST from Wilderness Radio:
http://www.fix.net/~jparker/wilderness/sst.htm
--
JT Croteau, N1ESE
something wrong with the PLL Reference Oscillator?
Thanks
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
is currently coiled up under the bench waiting for helpers to
come over and get it in the air. The only antenna up at the moment
here is an indoor 6-Meter dipole.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
MHz and I have FL1 (1.50)
selected per the recommendation of KE0Z. The -53 dB spike at ~1152 Hz
is oddly interesting to me, is this normal?
Thanks
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You
) for
feeding the computer when using digital modes.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
sees nothing.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
attempted to tune the filters yet as I am not yet finished
construction. This is just initial adjustment of L34.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post
by
the actual number of pins, followed by the gender (M=male, F=female).
For example, DB25M denotes a D-sub with a 25-pin shell size and 25
male contacts.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You
On 8/29/07, Thom LaCosta [EMAIL PROTECTED] wrote:
And some folks who laid out just as much money are NOT that upset
about the delay and the lack of announcements
Good things come to those who wait, patiently!
--
JT Croteau, N1ESE - Manchester, NH
, this internally generated signal is very
strong. I have a real hard time hearing the noise unless I crank the
can down quite a bit.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post
On 8/29/07, David Pratt [EMAIL PROTECTED] wrote:
What is the significance of ten minutes, Ron? Surely it doesn't take
that long to boil an egg ;-)
One must ID every ten minutes so this is likely the case.
--
JT Croteau, N1ESE - Manchester, NH
, utilizing the radio as an
amplifier. This setup was present in most radios manufactured in the
1930s onward by the Radio Corporation of America (RCA).
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must
-- Forwarded message --
From: Monty N5ESE [EMAIL PROTECTED]
Date: Aug 29, 2007 5:11 PM
Yikes?! Tonight!
Please join us for the QRP Barbershop tonight (Wednesday) 9PM EDT (8 PM
CDT, 7 PM MDT, 6 PM PDT).
If you haven't participated in this unique QRP contest before, I think
you'll
On 8/29/07, David Ferrington, M0XDF [EMAIL PROTECTED] wrote:
So the K3 is a sexy radio? I'll go along with that!
Whatever turns you (or the rig) on.
All four Elecraft rigs are sexy.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
rarely edit the subject before replying to messages in the
digest they received.
It's been going on since the beginning of reflectors and will continue
til the end.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft
anywhere in the K2 manual.
The other extra cap is an 821. I should only have two 821's (C4 and
C6). I have verified that C4 and C6 have the correct caps installed.
Anyone have any ideas what this 2.7C could be?
Thanks
--
JT Croteau, N1ESE - Manchester, NH
on
Elecraft's site.
My parts list, along with the PDF version, says the value of C22 is
pF). Something has obviously been cutoff. However, the
Description for C22 reads NPO, 2R7, 3, 3.3, or 3R3. No
reference to 2.7 at all.
--
JT Croteau, N1ESE - Manchester, NH
Ok, this has been resolved. Thanks for all replies. It has been
pointed out to me that 2R7 is 2.7. I still need to let Elecraft
know about the typo in the Rev. G manual.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post
I am at the point where I need to install the driver at Q6. The
manual states that I should have a 2SC2166 for the driver. However,
included with my K2 6233 is a 2SC5739. The parts list in Appendix A
of my Rev G. manual does not list any alternatives.
Anyone have any insight?
Thanks
--
JT
What is the proper crimper to use for the female pins (E620022) used
in Elecraft kits? Mouser part number would be wonderful.
Thanks
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must
the simple installation of four feet?
Has anyone else seen this? Heh.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub
probably a 1/16th or
1/32nd shorter in the front but I haven't measured yet so maybe my
eyes are playing a trick on me.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post
at transmit but it's supposed to be 13.3V.
I have to go out and buy a new DMM so I can do signal tracing (my
cheap DMM has fixed probes and I can't adapt them properly). Any
other ideas before I dive into signal tracing?
Thanks
--
JT Croteau, N1ESE - Manchester, NH
to it..
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help
there.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help
due the the high output of the Driver?
Thanks
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
.
Thanks
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Holy cow! I got it to work!
It was definitely a improperly tinned green lead on T2. So much for
buying pre-wound/tinned 'roids to save me some grief. Heh.
Thanks Don. What a relief. Time to button it back up and continue
40M TX alignment.
--
JT Croteau, N1ESE - Manchester, NH
may have been a bit more patient with their actual
installation as well. Who knows though, maybe not.
Thanks again.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post
lower power output is usually experienced on 10M but the high
current bothers me a bit. Should I be concerned?
Thanks
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post
Well, I think I answered my own question.
I keep forgetting that the K2 is only rated to 10W output. On 10M
with the control set for 10W out, I am showing 10W out with a current
draw of 2.56A.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft
of a break.
I think the W1 is next on my list.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
. So when it came
time to install the 78L06 and all I could find was the 2N7000, I said
damn!. I was almost able to salvage the part but a leg broke on me.
I can blame Elecraft all I want but it's my fault 100% for not paying
attention and assuming.
Many thanks.
--
JT Croteau, N1ESE - Manchester
People today seem to want everything to be smaller (except for their
big screen TV's). Everything is becoming smaller, not bigger.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must
Thanks to all who have replied, I've found one.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
not broke so I don't want to fix it. *grin* I'd also
rather not tie up my last PCI slot with a dual port serial adapter.
Thanks
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post
the one they provide will work with the K3. It should work fine for
the K2 as well.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr
operating, I used the DX Lab suite for digital operating,
rig control, and logging.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub
subscribed to about 20
email reflectors and get over 2000 emails a day. I use the power of
my email client to ease the task by creating filters to put them in
appropriate folders and to take care of spam.
--
JT Croteau, N1ESE - Manchester, NH
On 9/11/07, Loren Moline WA7SKT [EMAIL PROTECTED] wrote:
I am looking for a supplier for male SMA chassis connectors...
either 2 or 4 hole type. Anyone know where to order? Thanks!
Surplus Sales offers two kinds:
http://www.surplussales.com/Connectors/SMA-2.html
--
JT Croteau, N1ESE
On 9/12/07, Craig Rairdin [EMAIL PROTECTED] wrote:
There will always be users at every level, from n00bs to h4x0rz.
and we must not forget the 31337 h4x0rz.. especially the self-proclaimed type.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft
Uillean pipes for me please.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net
/2hzyl3
I think I will end up investing in a multiport serial adapter for my
PCI slot instead. heh.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber
On 9/14/07, David Fleming [EMAIL PROTECTED] wrote:
Is the noise constant or only when the software is polling the radio? I had
The noise is constant as soon as the adapter is plugged into the USB
port and before I even connect the rig to the adapter.
--
JT Croteau, N1ESE - Manchester, NH
On 9/14/07, Simon Brown (HB9DRV) [EMAIL PROTECTED] wrote:
Try a ferrite - usually works.
I have two snap-together split beads, one on each end of the cable,
and it doesn't do anything to the noise. This adapter is junk. heh.
--
JT Croteau, N1ESE - Manchester, NH
wise for it's intended
purpose; the 50MHz Sprint on October 20th. However, this shouldn't be
much of a problem as I am currently disabled and have more time than I
know what to do with lately.
Thanks for any feedback.
--
JT Croteau, N1ESE - Manchester, NH
if it is an issue. The XV50, and future
XV's will always be located right next to, or under, the K2.
Thanks
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber
On 9/20/07, Ron D'Eau Claire [EMAIL PROTECTED] wrote:
The signals between the XV and your K2 are all below 30 MHz, no matter which
transverter you are using.
Ya know, I'm an idiot. I just realized that after posting. I feel
real stupid now. Heh.
Thanks Ron.
--
JT Croteau, N1ESE
by default which it does for me. Hmm.
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
On 9/23/07, David Ferrington, M0XDF [EMAIL PROTECTED] wrote:
Thanks all, I have a mentor and I'm using K4FON's Morse trainer - just need
to put the time in.
Man, this K3 frenzy is causing everyone to screw up callsigns lately.
Hah! It's Tom, N0SS and Ray, G4FON's awesome CW trainer.
--
JT
modifying the same cable as I add options.
Thanks
--
JT Croteau, N1ESE - Manchester, NH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
on ~16 ea. for the
KPA100 run and the first XV and then 10 to each additional XV for a
total of 62. The XV's will be stacked on top of each other so I
could likely go even shorter but the cables become harder to work
with, for me anyway, when they get much shorter.
--
JT Croteau, N1ESE - Manchester
There is nothing like working Europe on 6M when such an opening
results here in New England. I will likely always have 6M capability
in the shack, it is a fun band. There can be openings in the
Winter-time but they are much, much more rare than the summer time.
--
JT Croteau, N1ESE
the XV50 with
no expectations other than to make at least one QSO. If more, all the
better.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber
On 9/27/07, Sam Morgan [EMAIL PROTECTED] wrote:
Anyone have a K102 they would like to sell?
You must be referring to a KIO2. IO as in Input/Output. No such
beast as a K102.
Just an FYI.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft
' in two
weeks, we agreed we should add some week t'dat and conservatively set
da damn official K3 fust ship date fo' Monday Oct 8d.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must
can't make fun of the situation every once in a while, what
the heck? You guys sure can put up with the whining.
.. and that is all I have to say about that. I will return you to
your whining and questions about things already answered in the
archives and in the FAQ.
--
JT Croteau, N1ESE
.. I won't do anything like
this again. *grin* Meanwhile, I suggest to several people, that they
go out and rent Airplane - The Movie, and see if June Cleaver should
also be called a racist for speaking Jive.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx
'. Most people frown upon contests every weekend
but get on the air during a contest and you'll have DXCC in no time
flat.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber
I wish I still had my 5/8-wave 20M vertical, it was about 39' tall if
memory serves. That was a great antenna for DX work on 20.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must
of slobbering.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman
installing variable caps
during K2 assembly.
Thanks
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
week.
Meanwhile, FedEx just delivered, as I was typing this, my XV50 and
K60XV so now I have something new to break, er build, in the meantime.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You
Drew,
Have you ruled out the simple obvious? Felt washer is no longer
putting enough friction on the VFO knob to keep it still?
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must
W3FPR and others frequently recommend good quality analog meters for
doing several alignment procedures and for performing countless tests.
I'd like to get one but have no clue what to look for in this day and
age of digital test equipment.
Advice, recommendations please?
Thanks
--
JT Croteau
succesful enclosure and tool and
die business that can stand alone. How lucritive? I'm not sure.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list
be played by Nicolas Cage.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net
. Heh, thanks Tree.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman
current products.
Thanks for any help on just what to do with L17. I presume I'm to
just install it as I do L15 and L16.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber
the 50 MHz parts envelope but
found a local source and this is no big deal.
My biggest gripe though are with these docs. I used to be a technical
writer so maybe I am a bit anal with this pet peeve.
Thanks
- JT
On 10/8/07, JT Croteau [EMAIL PROTECTED] wrote:
I'm trying to build my first XV
The issues are now being addressed, Gary and I are now in
communication with one another. Thanks Eric/Wayne.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post
pins for things like XV and
KAT100 control.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
On 10/11/07, Mark Bayern [EMAIL PROTECTED] wrote:
If your K2 cable had only three wires, signal ground, send data and
receive data, there is no _major_ difference.
Big difference. Send Data and Receive Data on the K3 are opposite
that of the K2.
(According to the K3 web manual)
--
JT
between the K3 and
the computer's RS232 port or USB-to-RS232 adapter. Use a high-quality,
fully shielded cable.
(Page 18, Web version of K3 manual)
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
(unused). Refer to your software
documentation to see if PTT or keying via RS232 lines is available.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list
On 10/11/07, JT Croteau [EMAIL PROTECTED] wrote:
You don't need to. The K3 is wired for DTS and RTS keying, see page
18 of the web manual:
I should have said DTR not DTS, my bad.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing
On 10/11/07, Thom LaCosta [EMAIL PROTECTED] wrote:
And for those that care to discuss things without treading of the toes of
varios
folks...there's a venue at www.zerobeat.net/smf/
Thom is so 31337. :-D
--
JT Croteau, N1ESE - Manchester, NH (FN42gx
to be locked on this band as the frequency doesn't
change as I spin the VFO. Direct frequency entry appears to work but
as soon as I touch the dial it jumps back to 21.100. All other bands
are working fine, this is only a 15M problem.
Any ideas?
Thanks
--
JT Croteau, N1ESE - Manchester, NH (FN42gx
the way I want them.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman
Ed, thanks for bringing the K3 to NEAR-fest.. it was great to see both
of you there.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber
Well, CAL PLL alone did not work. I had to do a master reset.
Now to put all my settings back...
Thanks Don
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post
On 10/14/07, Hugh Valentine [EMAIL PROTECTED] wrote:
1)Use your hobby.Everyone Meet on 80 SSB and
Not everyone has real-estate for low band antennas and there are
several folks in the club who refuse to use any mode other than CW.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx
Wrong reflector, sorry.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net
am pretty certain the K2 is properly aligned with WWV @ 10 MHz.
Thanks
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change
Anyone intimately familiar with the W1 watt meter know if it'd be
possible to modify it work up to 50MHz?
Thanks (however, watt I really need to do is just get a Bird one of these days)
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft
it might be
external somewhere in the environment around the shack?
Thanks
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr
Elecraft is $430.00 with the oven. I'm selling for
$350.00 delivered anywhere in the US. PayPal preferred but I will
also accept a postal money order.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
Price reduced to $325 to hopefully entertain a quick sale.
Thanks
On 10/21/07, JT Croteau [EMAIL PROTECTED] wrote:
Selling my recently built XV50 transverter. It works fine, I have 3
QSO's with it, but I find myself obsessed with a new project I want to
build. It comes with the crystal oven
The XV50 has been sold, thanks.
--
JT Croteau, N1ESE - Manchester, NH (FN42gx)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
in the Rework
Eliminators. I would like $950.00 for the package and I will pay for
the shipping anywhere in the US. Payment via PayPal is preferred.
Some pictures can be seen here:
http://n1ese.qrpradio.com/K2/
Thanks
--
JT Croteau, N1ESE - Manchester, NH (FN42gx
Price reduced to $850.00 delivered to match my QTH ad.
On 11/3/07, JT Croteau [EMAIL PROTECTED] wrote:
Selling my K2 #6233 that I just put on the air on October 2nd. Rig
works perfectly, I have 147 QSOs logged since 10/2. It is configured
as follows:
K2
K160RX
K60XV
KAT2
KIO2
KSB2
1 - 100 of 148 matches
Mail list logo