[Elecraft] Question re KX2 and KXPA100

I had that problem manifest itself on my KX3/KXPA100 system. Double check that both ends of the KX3 to KXPA100 adapter cable (that little black box that is connected to the PA100 via the RJ45 connector) are completely mated/pushed in where they are inserted in the ACC1 and ACC2 jacks on the

[Elecraft] Early Morning QRPing on 80 Meters

Pete et al --- I'm on the low bands (160, 80 and 40) almost every morning from 1200Z (or so) 'till 1400Z..80, in particular, is where my RBN reports are THE most promisingBUTvery seldom do I hear any QRPers on 3.560. Often, I get so bored with the little CW activity that I move to

Re: [Elecraft] KX3-KXPA100 operation

One other item of interest - I do not have an ATU in the KX3 .. I have an ATU at the out at input to the antenna From: James Rodenkirch Sent: Tuesday, January 31, 2017 7:16 PM To: elecraft@mailman.qth.net Subject: KX3-KXPA100 operation I just

[Elecraft] KX3-KXPA100 operation

I just connected my kx3 and a newly purchased kxpa100 (no KXAT100 ATU)...have control of pwr from milliwatts to 100 and asll seems to be working correctly exceptwhen in cw, the earphones on and the power set at 9 watts, I opted to increase power past 10 - when I did some noticeable amount

[Elecraft] Random wire lengths for antennas

Emory - before you cut any wire, go to the below url and peruse all of the info - unless you desire to operate have a 1/2 wavelength antenna (not a bad thing) and have a 1/2 wavelength tuner for the band of interest, mgo to the below url for recommended wire lengths that avoid 1/2 wave antenna

[Elecraft] Anything to be "aware of" when connecting KX3 to new KXPA100?

"Unless you plan to use two antennas connected to the amp, use the KXPA100 utility to disable Ant 2 so that you do not accidentally select it when hitting auto tune. If you decide to go add a second ant later on, you can easily change it." "hitting auto tune"? where? In/on the KX3 or the KXPA?

[Elecraft] Anything to be "aware of" when connecting KX3 to new KXPA100?

Just ordered the KXPA100 (no KXAT100) and KXPACBL cabling package - so wonder if there are any "watch out for this" tidbits of info to be aware of when connecting the cabling and turning it on. Offline replies ok...72 de Jim Rodenkirch K9JWV

[Elecraft] Very short 80m antenna

A couple of other "info sites to explore," Vic. http://www.k7mem.com/Electronic_Notebook/antennas/shortant.html http://www.qsl.net/vk3jeg/loadpole.html http://www.qsl.net/vk3jeg/loadpole.html (good info on capacitive hats here) 72 de Jim Rodenkirch K9JWV

[Elecraft] Very short 80m antenna

Don't give up on the notion of a shortened vertical just yet, Vic. Peruse this site and see if there is anything that can help - http://www.arising.com.au/people/holland/ralph/shortvert.htm 72 de Jim Rodenkirch K9JWV __ Elecraft

[Elecraft] 160m Doings - not totally "flash mob" but all GREAT CW fun!

If any of you would like to take another bite of the Topband apple, then be sure to join the 12th annual QRP 160m sprint sponsored by the North American QRP CW Club (NAQCC) that occurs in North America this coming Tuesday (repeat,TUESDAY evening, which coincides with the 40m Fox Hunt). This

Re: [Elecraft] OT(sorta) Setting up KX3 for JT9 ops

Tnx, Jim Sent from my Verizon Wireless 4G LTE smartphone Original message From: James Bennett <w6...@me.com> Date: 01/19/2017 10:16 AM (GMT-07:00) To: James Rodenkirch <rodenkirch_...@msn.com> Cc: Elecraft Reflector Reflector <elecraft@mailman.qth.net> Subj

Re: [Elecraft] OT(sorta) Setting up KX3 for JT9 ops

Question answered --- tnx to those who replied... From: James Rodenkirch Sent: Thursday, January 19, 2017 6:20 AM To: elecraft@mailman.qth.net Subject: OT(sorta) Setting up KX3 for JT9 ops Anyone operating JT(? If so, anything peculiar for setting up ALC

[Elecraft] OT(sorta) Setting up KX3 for JT9 ops

Anyone operating JT(? If so, anything peculiar for setting up ALC in JT9 versus JT65?? Offline replies "ok." Tnx, inn advance, for any info you can proffer - Jim R. K9JWV __ Elecraft mailing list Home:

[Elecraft] OT (sort of) -- went from WSJT-X vs 1.6 to vs 1.7 (have a KX3) and having problems...

...first off my mea culpa entreaty 'cuz I lost documentation on vs 1.6 "settings" and then loaded 1.7! Could someone knowledgeable on moving from 1.6 to 1.7 contact me offline and help me get 1.7 working??? Thank you, in advance, for your assistance72 de Jim Rodenkirch K9JWV

[Elecraft] Need help with getting WSJT X to continue working with my KX3

Sent from my Verizon Wireless 4G LTE smartphone I am receiving info needed to correct this problemtime sync may be off or intermittent. I am using Dimension 4...may try something different. Thanks to all who replied. Jim R. K9JWV On 12/29/2016 9:17 AM, James Rodenkirch wrote

[Elecraft] Need help with getting WSJT X to continue working with my KX3

Problem: I can turn on the KX3, start WSJT X 1.6 and commence decoding and making QSOs. However, if I change to a different band, I can't make QSOs on that band or go back to the original band and make Qs. Adjusting ALC on the new band works...power out is the same, etc. Is there some

Re: [Elecraft] Setting the KX3 up for JT65

OK - couldn't figure out what I had done so opted tom use the kx3 utility to restore the latest config I hadBINGO!! All is well.thanks to those that replied72 de Jim R. K9JWV From: James Rodenkirch Sent: Tuesday, December 20, 2016 6:06 AM

[Elecraft] Setting the KX3 up for JT65

I’ve been away from JT65 ops with my KX3 for so long I forgot what to do…I have used t5he KX3 in JT65m before but been many months so need to restart. I have WSJT running on my Microsoft Surface Pro 2 and haven’t messed with those at all, e.g., CAT, 8 data, 2 stop, etc. The decode works well.

[Elecraft] K3s' KBPF3A and KTCX03

1) Do I have this "right"??? The KBPF3A module adds general coverage down to 100 khz AND provides a .5 milliwatt output for/on the 630 meter band?? 2) Is anyone operating JT9/65 and/or WSPR successfully without the KTCX03 (those are two of the modes I'll employ on 630 meters) 72 de Jim R.

Re: [Elecraft] N1MM and KX3

Why didn't you just purchase the USB interconnect cable, Bill? Add two interconnect audio cables for mic and headphone and you're wired for quadrasonic multiplexwell as far as utilizing your computer for contest logging and operating CW as well as JT9/65, PSK-31, etc. What am I missing??

Re: [Elecraft] N1MM and KX3

Well, FredI coulda listed it as F1 CQ, {CATA1ASC KY cq TEST * * test;} Regardless, either "version" produces the same..adding the 2nd cq (for either 'version') results in nothing out of the KX3 From: Cady, Fred Sent:

[Elecraft] Summer operating events

Hey, it's tuff finding decent summer contesting "challenges" that are fun and don't occupy the ENTIRE weekend BUT, here's an upcoming event you might could enjoythe Summer Stew Perry 160 meter 'test.' Go here for the details: http://www.kkn.net/stew/ Remember, QRP

Re: [Elecraft] [KX3] Bands are open -- CW WPX is a great time to test-drive a new KX2

Operating as a 160 single band QRP entry this time around...160, early this morning (0600Z) in s/w Utah, was in great shape, S3 noise level, solid copy on signalsyes, the rapid QSB is there but, just don't send cut numbers for crying out loud, HK1R was solid 579 in to s/w UT, worked Eric,

Re: [Elecraft] ID'ing small 4 pin male connector on the bottom of the KX3

That beez it, Ken...to all I have them answer and thanks to all that responded... From: Ken G Kopp <kengk...@gmail.com> Sent: Wednesday, May 11, 2016 7:24 AM To: James Rodenkirch JamesR; elecraft@mailman.qth.net Subject: Re: [Elecraft] ID'ing small

Re: [Elecraft] Feedline loss w/wo tuner (was Sherwood's receiver performance table updated)

160 through 15). THAT's my foci and resulting mantra "No auto tuner or tuner or whatever in the shack!!" From: Ken K6MR <k...@outlook.com> Sent: Wednesday, April 27, 2016 12:52 PM To: James Rodenkirch; elecraft@mailman.qth.net Subject: RE: [El

Re: [Elecraft] Sherwood's receiver performance table updated

.5/72 Jimm R. From: Ken K6MR <k...@outlook.com> Sent: Wednesday, April 27, 2016 12:10 PM To: James Rodenkirch; elecraft@mailman.qth.net Subject: RE: [Elecraft] Sherwood's receiver performance table updated No problem. Yes, open wire line has its

Re: [Elecraft] Sherwood's receiver performance table updated

4 db delta, depending on the band in use... From: Ken K6MR <k...@outlook.com> Sent: Wednesday, April 27, 2016 11:31 AM To: James Rodenkirch; elecraft@mailman.qth.net Subject: RE: [Elecraft] Sherwood's receiver performance table updated But the theory works whether you have open w

Re: [Elecraft] Sherwood's receiver performance table updated

Did not mean to sound argumentative, Ken.apologize if it came out that wayI am "involved" in this discussion becuz' of Don's initial post about new hams not understanding the advantageous aspects of open wire feed line ____ From: James Roden

Re: [Elecraft] Sherwood's receiver performance table updated

Wowlots of good stuff emanating from this discussion - tnx to all for participating For Jerry - there are other reasons for employing an ATU in the shack - e.g., using open wire line feed line from the antenna back to the xmtr. _ From: Jerry

Re: [Elecraft] Sherwood's receiver performance table updated

It is not "the principle behind the use of open wire feed line," Ken IF, I place an antenna auto tuner at the base of, for instance, a vertical and feed the tuner with low loss coax I understand the use of open wire feed line and an ATU prior to attaching to the xmtrBUT...see above -

[Elecraft] K1 (still) a classic!

Absolutely a fun radio, Curt --- one slight caveat, though... Any radio is truly "fun" 'cuz/as band conditions/propagation AND one's "to some degree, efficient" antenna allow(s). 71.5/72 de Jim Rodenkirch K9JWV From: "Curt" Date: 2016-04-02

[Elecraft] Ok......I've lost the 17 meter band on my KX3

So, I must have pushed some button incorrectly but.no 17 meters as I go through the band changes.sheesh, how do I resurrect 17 meters? 72 de Jim Rodenkirch K9JWV __ Elecraft mailing list Home:

Re: [Elecraft] Ok......I've lost the 17 meter band on my KX3

OK.found BND MAP in the menu and set 18 to "in" Thank you, Tom and Sean... From: Sean Donovan <sean.patrick.dono...@gmail.com> Sent: Friday, March 18, 2016 8:19 AM To: James Rodenkirch Cc: Elecraft@mailman.qth.net Subject: R

Re: [Elecraft] Craig KD0TXL...best antenna

Conflating narrow bandwidth with high efficiency isn't a good thing to do, necessarily. Efficient 160 verticals across the band can be realized if one "fattens the radiating element." Sent from my Verizon Wireless 4G LTE smartphone Original message From: Jerry Moore

Re: [Elecraft] How to make the KX3 controlled by logging soft ware like N1MM??

Tnx to all that replied - and, now, I can control the KX3 with N1MM INCLUDING keying the KX3 via F key macros, in CW, with just the USB to serial cable.AWESUM!!! 71.5/72 de Jim Rodenkirch K9JWV __ Elecraft mailing list Home:

Re: [Elecraft] How to make the KX3 controlled by logging

Tnx to all that replied - and, now, I can control the KX3 with N1MM INCLUDING keying the KX3 via F key macros, in CW, with just the USB to serial cable.AWESUM!!! 71.5/72 de Jim Rodenkirch K9JWV __ Elecraft mailing list Home:

Re: [Elecraft] How to make the KX3 controlled by logging sofftware like N1MM??

Bob - N3MNT You replied, The KX3 interfaces seamlessly with N1MM+ for both logging and sending CW memory locations. It tracks freq and band and mode." Absolutely correct...but...with only one cable into the ACC-1 plug - from my USB connection I cannot key the radio!! 72...Jim R.

Re: [Elecraft] How to make the KX3 controlled by logging sofftware like N1MM??

72 de Jim R. K9JWV From: Don Wilhelm <w3...@embarqmail.com> Sent: Monday, November 30, 2015 11:56 AM To: James Rodenkirch Cc: Dale Putnam Subject: Re: [Elecraft] How to make the KX3 controlled by logging soft ware like N1MM?? Jim, Keying is an entirely different

Re: [Elecraft] How to make the KX3 controlled by logging sofftware like N1MM??

Just to clarify - I am attempting to make N1MM contesting software interface with my KX3. From: James Rodenkirch Sent: Monday, November 30, 2015 10:44 AM To: elecraft@mailman.qth.net Subject: Re: How to make the KX3 controlled by logging sofftware like N1MM

[Elecraft] How to make the KX3 controlled by logging sofftware like N1MM??

How do you control the KX3 with N1MM??? Do I need another device like this SUCCI?? http://www.kotarov.com/projects/succi [http://www.kotarov.com/_/rsrc/1369684755650/projects/succi/IMG_9309.JPG?height=240=320] SUCCI - Vesselin Kotarov / LZ5VK SUCCI

Re: [Elecraft] How to make the KX3 controlled by logging sofftware like N1MM??

ORis there a logging program that DOES work with the serial to USB cable only Tnx, in advance, for any help you can proffer...feel free to contact me off line -- rodenkirch_...@msn.com 71.5/72 de Jim Rodenkirch K9JWV From: James Rodenkirch Sent

Re: [Elecraft] KX3 VSWR problem

WD4SDC wrote Equipment: KX3 S/N 7210, FW 02.25 Problem: 6M band -> VSWR 1.8:1 (KX3 meter) on 50ohm load connected directly to ant connector (no cable). Followed by this UPDATE: The test was to disconnect the remove the ATU board and connect the RF board directly to the antenna port - which

[Elecraft] HELP!!!

I am trying to set up my KX3 for JT65 operation...when ever I plug my audio cable from the computer into the mic input jack the kx3 goes in to xmt.what is up with that??? I am using supplied cable from Elecraft... __ Elecraft

Re: [Elecraft] HELP!!!

Tnx Kevin ...but, even with the computer off and regardless if in USB or data A mode and with PTT selected the xmt light comes on... From: kevino z <balloon.experim...@outlook.com> Sent: Saturday, November 21, 2015 11:43 AM To: James Rodenki

Re: [Elecraft] HELP!!!

That did it, Wunder..tnx to all that answered!!! From: Walter underwood <wun...@wunderwood.org> Sent: Saturday, November 21, 2015 12:54 PM To: James Rodenkirch Cc: elecraft@mailman.qth.net Subject: Re: [Elecraft] HELP!!! Set mic button off in the

[Elecraft] PSK31 for my KX3 with a Samsung Galaxy 4 Android....

http://kx3companion.com/ [https://kx3companion.files.wordpress.com/2014/03/screenshot_2014-07-12-07-35-11.png] KX3 Companion The KX3 Companion in an app that will let the power use of your Elecraft KX3 HF radio easier and lighter. No need for a PC! It will let

Re: [Elecraft] Get the kids off the street - making my move!

Pete: you replied with this...I find that WSJT-X works better for me than JT65-HF and is written by Joe Taylor (K1JT) himself. I see this at his website: WSJT-X implements JT9, a new mode designed especially for the LF, MF, and HF bands, as well as the popular mode JT65. Both modes were

[Elecraft] Fred Cady kx3 manual

Anyone have an extra copy of Fred's KX3 manual they'd part with? 71.5/72 de Jim Rodenkirch K9JWV __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

[Elecraft] K3S query

Anyone using the K3S in cw with no roofing filter(s) and enjoying how it sounds during a contest? Does the DSP filtering and the audio peaking filter do the job for you without a 500 hz roofing filter? Thank you, in advance for your thoughts72 de Jim Rodenkirch K9JWV

[Elecraft] 2015 Oceania DX Contest - 3/4 October (PHONE) and 10/11 October (CW)

I entered the CW contest last year and enjoyed the challenge of working OC entrants with QRP power -- they added a QRP category in 2014 so, if time permits, get on and participate.72 de Jim R. K9JWV From: i...@oceaniadxcontest.com To: i...@oceaniadxcontest.com CC:

[Elecraft] Graphene

The thickness of a future Elecraft rig - a K-5 or K-6, perhaps - may be constrained by the thickness of the components but not by the thickness of the board http://biggeekdad.com/2014/09/graphene-miracle-material/

Re: [Elecraft] K2's ATU vagaries

combination last used for the TUNE on each band will be set when you return to that band. Note for KAT100 users - POUT is not an available menu option - you can use CAL which bypasses the L/C elements completely. 73, Don W3FPR On 4/30/2015 8:21 AM, James Rodenkirch wrote: While altering my

[Elecraft] Assistance setting up K2 for JT-65 mode

I'm looking at jumping in to JT-65 mode of operating and see where a Tigertronics Signalink USB Interface box may be the easiest way to get started. If anyone has utilized that approach and has some lessons learned to share, please contact me off-list for a QA session or two. 71.5/72 - Jim

[Elecraft] WTB K160RX

If someone has a K160RX for the K2 that is excess to their needs I’d be interested in chatting about transferring ownership to me @ rodenkirch_...@msn.com …71.5, 72 Jim Rodenkirch K9JWV

[Elecraft] WTB K160M

If someone has an K160M for the K2 that is excess to their needs I’d be interested in chatting about transferring ownership to me @ rodenkirch_...@msn.com …71.5, 72 Jim Rodenkirch K9JWV Sent from Windows Mail __ Elecraft mailing

[Elecraft] WTB a K1 and four band module

If anyone has a basic K1, in kit form, partially finished or finished and it's still not working correctly, I’d be interested in purchasing it. If it doesn't have any bnd modules, that's ok - have one of those. If anyone has a four band module thy don't need, contact me as well. Contact me

[Elecraft] Found a K1!

Should be here today../.it will have the four band 40/30/20/15 module and the ATU along with a two band module. Going to have the two band module changed to 80/17 and, when not traveling, will swap out the ATU for the two band module and have an 80/40/30/20/17/15 rig (already have an auto

Re: [Elecraft] Found a K1!

Bruce: don't consider this the beginning of an argument but.I recall having both modules installed, at the same time, in my previous K1..was I dreaming that?? From: bef...@myfairpoint.net To: elecraft@mailman.qth.net CC: rodenkirch_...@msn.com Subject: Re: [Elecraft] Found a K1!

Re: [Elecraft] Found a K1!

on a 4 band board, and 40/17 on a 2 band board. GL, Bruce N1RX From: James Rodenkirch [mailto:rodenkirch_...@msn.com] Sent: Monday, January 19, 2015 10:35 AM To: Bruce Beford; elecraft@mailman.qth.net Subject: RE: [Elecraft] Found a K1! Bruce

[Elecraft] List of K1 modifications

Does anyone have a list of all K1 mods (those approved by Elecraft and those that others have installedOR the URL of a site that does and can vector me to? Thank you, in advance, for your assistance. 72, Jim Rodenkirch

[Elecraft] Searching for a K1

Anyone have a used K1 for sale? One with a four band module would be ideal...please reply off list to rodenkirch_...@msn.com 72, Jim Rodenkirch K9JWV __ Elecraft mailing list Home:

Re: [Elecraft] Antenna question

And QST recently published a piece showing that a better use of a 43 ft vertical might be as the center support for horizontal dipoles for 80 and 40, a concept with which I strongly agree. (smiley face annotation removed) As stated by a frtend of mine, after eading the above little ditty and

[Elecraft] Elecraft K1 for sale

I am reducing the price asked for my K1 from $515.00 plus shipping to $500.00, including shipping. The particulars: Serial # 589 Six bands - (160 and 80 in a two band module); (40,30 20 and 15 in a four band module) KNB1 Noise Blanker Finger Dimple K1LCD Backlight mod K6XX CW indicator when

[Elecraft] K1 for sale

Have a K1 for sale as I'm moving to another Ten Tec rig. Pric is $515.00 plus shipping. Particulars: Serial # 589 Six band - 160,80,40,30 20 and 15 KNB1 Noise Blanker Finger Dimple K1LCD Backlight mod K6XX CW indicator when zero beat All documentation Just had it aligned, varification of

Re: [Elecraft] [QRP-L] Antenna Question

Please treat this reply to the below thread where an emphasis on linear loading being mo betta than a loading coil as a dialectic discussion. Something about that posit - linear loading is more efficient than a loading coil - didn't ring true with me so I did a little digging. Now, keep in

Re: [Elecraft] [QRP-L] The Chinese KX3

If they can produce a similar product at a reduced cost, including the absurdity of the current add on costs that Elecraft charges, good for them! Hope they are successful - successful meaning their version offers like functions and specifications, at a reduced cost! 72, Jim R. K9JWV

Re: [Elecraft] [QRP-L] The Chinese KX3

copy. Sent from my iPhone On Apr 13, 2012, at 9:32 AM, James Rodenkirch rodenkirch_...@msn.com wrote: If they can produce a similar product at a reduced cost, including the absurdity of the current add on costs that Elecraft charges, good for them! Hope they are successful

Re: [Elecraft] [QRP-L] The Chinese KX3

announcements in Chinese with Google Translate as your only friend when trying to figure out what's going on. But to be honest, looks like a spoof to me. A well made spoof, but still a spoof. 73, Thomas M0TRN On 13 April 2012 15:32, James Rodenkirch rodenkirch_...@msn.com wrote

Re: [Elecraft] [QRP-L] The Chinese KX3

Snort! Your observations, are as anecdotal as can be and.continue to make my point --- a point that was started when I sent out the reply: If - IF - they can produce a similar product at a reduced cost, including the absurdity of the current add on costs that Elecraft charges, good for

Re: [Elecraft] [QRP-L] The Chinese KX3

. 73, Thomas M0TRN On 13 April 2012 21:55, James Rodenkirch rodenkirch_...@msn.com wrote: If - IF - they can produce a similar product at a reduced cost, including the absurdity of the current add on costs that Elecraft charges, good for them

Re: [Elecraft] [QRP-L] The Chinese KX3

don't believe so. Did I pay too much for products from 'other' radio manufacturers...i sure did much to my continued angst. 20/20 hindsight can sometimes be a bummer 73's Gary On 14 April 2012 08:49, James Rodenkirch rodenkirch_...@msn.com wrote: Elecraft follows the Apple model - or vice