Thanks to all for the great suggestions (the SNR of the responses was
appropriately high!).
I did some experiments with the RSP2 and HDSDR. It was very close to what I
was looking for and I will revisit it in the future when I am looking for
specific interferers, but I set it aside when I saw a v
In looking back at my original post..I omitted the word NOT.
Thus "all PL-259 connectors are not all created equal".
Sorry folks, and thanks Jim for catching the over site.
73
Bob, K4TAX
On 8/8/2017 12:42 AM, Jim Brown wrote:
On 8/7/2017 3:06 PM, Bob McGraw K4TAX wrote:
PL-259 co
Situation: Tuner inline between K3s and known good dummy load.
1) Tuner off - K3s tunes 1:1 instantly
2) Tuner on in bypass - K3s tunes 1:1 instantly
3) Tuner on, and in Manual OR Auto Mode, tuner clicks and then Mode
light starts blinking.
All components in signal path obviously AND tested know
The ATU blinks the MODE LED when a tune has been started, but not enough RF
is arriving from the exciter to proceed. It's waiting for about 20 watts
from your exciter. If you want to cancel the tune, tap TUNE again.
Don't use both the K3 internal ATU and the KAT500 ATU together. One or the
other
Hi Clay,
I could easily reproduce your problem. Note: I do not have the AUX cable
connected. Apparently you just pressed TUNE on the tuner. That will not
start the K3 sending a tuning tone. Thus the blinking LED (MAN led if in
manual mode, AUTO LED if in in AUTO mode). You must press and hold the
Thanks for the response, but that's not the issue here. K3s tuner in
bypass.
With tuner in bypass, and "TUNE" held down, SWR on K3s is 3.6.
Repeat with KAT500 in Manual mode, the SWR reading on K3s is 12.6:1 or
higher.
Repeat in AUTO Mode, and SWR goes to 99.9:1 because the KAT500 breaks
the si
Did not include that in original post, but I AM holding the XMIT/TUNE
button in to send the RF sig to KAT500.
See just prior response.
Also, K3s power set at ABOVE 7 watts both 10 Watts and above 12-13
to engage K3 PA...
Trying to tune using the KAT500 causes the blinking mode light and an
o
I'm the process of setting up WSJT to run FT8 on my K3, using an
external sound card.
Set DATA A mode on the K3, turned of Windows sounds (which don't go
through my external sound card anyway).
The WSJT instructions say to press the Tune button -- in WSJT, not the
K3 -- and you should hear a
When I took out the KPAIO3 ready to install the 470mfd 16vw cap, as required
for the above mod, I noted that my pcb looked different to that shown in the
installation instructions. The track that as shown on figure 6 page 5 of the
instructions that is routed away from the left most of the 4 pads
Put a dummy load on output of KAT500 and if that doesn't give 1:1 then you have
a cable issue.
73,
Bill
K9YEQ
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Clay Autery
Sent: Tuesday, August 8, 2017 12:17 PM
To: elecraft@
We did that, and it was an instant 1:1
Finally figured it out... this particular KAT500 spent its life hooked
to a basic K3... It was behind on firmware updates by ELEVEN versions...
Updated to current and it immediately started working... The version it
had was PRE-K3s by several years.
11 matches
Mail list logo