; External Speaker; The Elecraft
K3S and P3 by Fred Cady; K3S ATU; K3S Gen. Cov. RX Module; KFL3C-400; 2.8
for 2.7 kHz swap; KFL3B-FM; P3 Video/FFT Adapt.; P3 TX Monitor Adapt; 1.8-54
MHz 200W; incl. P3TXMON
Thanks a lot,
Tom Norris NB5Q
attribute the errors to trying to
>> work too late into the night. So, don’t try to overdo and don’t rush it.
>>
>> 73,
>>
>> John
>> WA1EAZ
>>
>> > On Dec 1, 2017, at 11:11 PM, Tom Norris wrote:
>> >
>> > My first post, new bu
I have made my way to preparing to install the filters I purchased for the
project. I have read (someplace) that I could place the filters on the RF
board skipping the locations that I might later decide to add. With
thoughts of possibly adding narrower SSB and data filters I am planning to
install
Newly assembled working great so far.
At the Owners Manual Calibration Procedures pg 52 (Fred Cady book Elecraft
K3S and P3 referred me to Owners Manual for some Calibrations after going
through Configuring the K3S pg 26...)
Wattmeter:
Both CONFIG:TUN PWR and PWR SET to NOR (KPA3A not installed yet
PM, Don Wilhelm wrote:
> Tom,
>
> The K3 wattmeter calibration is different than the K3 Utility TX gain
> calibration.
>
> Do the wattmeter calibration as indicated in the manual, and then you can
> do the TX Gain calibration from K3 Utility.
>
> 73,
> Don W3FPR
>
I have completed the K3S kit assembly but had questions about the receive
sensitivity. On the advice of Gary, AB7MY at Elecraft Support (Thank you) I
have went through the filter configuration again via the K3 Utility and
improved things to the point that I now hear AM broadcast stations but few
ha
I'm beginning my learning curve with my new K3S Kit (after a trip to
Elecraft for them to correct the 400hz filter I put in backwards! Otherwise
it was a good, fun build). I'm wanting to practice CW sending and I am able
to see my K3S paddle input characters in the K3S VFO B. But I am not able
to r
bed in my previous post below.
>
Thanks, Tom NB5Q
>
> --
>
> Message: 5
> Date: Fri, 2 Mar 2018 21:06:41 -0700
> From: Tom Norris
> To: Elecraft List Server
> Subject: [Elecraft] K3 utility to monitor extended display of
> cha
I've searched the internet without luck, just wondering if anyone here has
the answer to this question. They would be on the same mast at about 30'
elevation or so.
73, Tom NB5Q K3S
__
Elecraft mailing list
Home: http://mailman.qth.net/mai
I don't want to re-invent the wheel so I'm asking what method and
attachment point, to each piece of equipment, you experienced K-Line owners
use to bond the K3s, P3, SP3, etc. and then on to the station ground. I
have
Thank you, Tom NB5Q
I am reviewing Jim's (K9YC) slides and have gotten to the DC Power Supply
(forget the slide #s) . I currently have a Alinco DM-330MV which supplies
my needs. However, after looking internally and studying the schematics,
there is no way to isolate circuit return (negative) from the chassis case
gro
I have K3S Serial Number 11459 and a P3 and would like to communicate with
N3FJP ACLog and SKCCLogger at the same time or one of the logging programs
and the K3 Utility. Technology has raced past me! Is the bottle neck with
only one com port available from the K3S?
Thanks, Tom NB5Q
___
Thank you all for the learned information! I will try LP-Bridge first and
keep Win4K3Suite in mind, Tom, thanks for mentioning it and I can tell you
have some loyal followers!
Tom NB5Q
On Wed, May 27, 2020 at 6:44 PM Lou W0FK wrote:
> Try LP-Bridge. It's a solid program, and although it's been s
13 matches
Mail list logo
