My locate command segfaults. I'm running a 7.1 installation.
Anyone have any clue what could be happening? Thanks.
-- Stephen
I am resending this message because I did not see it posted after
*12 hours*. My updated message is at the bottom.
> So after wasting/playing 4 hours trying to understand
> ipchains and correct it to secure it, I've run into a
> problem. I have set ipchains to forward MASQ 192.168.1.0
> and de
I am trying to console up a linux box. Everything works great, except lilo. Lilo
will write to the console, but will not take input from it, only the keyboard?
Here is the statement from my lilo.conf:
serial=1,9600n8
any ideas?
thanks, --jc
-
John Craig
Prod. Ops.
[EMAIL PROTECTED]
[EMAI
On Sat, 24 Jun 2000, Denis HAVLIK wrote:
> :~>Is there any command to copy HD to HD ,like command line "diskcopy" under DOS
>
> yes.
>
> :~>,my friend tech me
> :~>dd if=/dev/hda1 of=/dev/hdb1 bs=1024k,but must run it under single mode.
> :~>anyone tell or me? or another good command to use?than
Hi!
I have an old colorado 250 internal tape. It's qic80 compatible.
But I'm unablle to use it.
I have tried:
taper -T ftape
taper -T zftape
The difference between smtp servers and pop3 servers is that one recieve
mail and the other sends your mail to its destination, pop3 or post
office protocol sends your mail out whereas smtp is used to recieve mail
from various locations.
calvert
Computer Mall Inc, for all your computer needs
Perhaps you might want to check out your CMOS settings.
cally
Computer Mall Inc, for all your computer needs and more if we don't have
it we'll order it within 5 working days.
784-485-6137 phone or fax 784-485-6586
Kingstown
St Vincent
_
On Mon, Jun 26, 2000 at 06:23:26PM -0400, thus spake Phil:
> Hi everyone
> I have been running Mandrake since 6.0 I have just installed a fresh 7.1
> Its nice :-)
> However I configure ppp networking with Linuxconfig and select the user
> (de)activate option and it all works fine
> BUT '
> after a
Thanks. I will give it a try, but last time I looked, 7.1 wasn't
available at any local stores and the only cdrom burner I own is in the
machine I can't boot. I guess I could install windows, but that thought
sends shivers down my spine.
--sam
[EMAIL PROTECTED] wrote:
>
> > I just built a new
I'm installing Mandrake 7.1 and I'm trying
to use XF86_FBDev because I have a S3 Trio 3D card and can't get it working with
the XFree86 SVGA drivers.
I've installed the kernel with framebuffer
support and modified my lilo to boot with a vesa mode of 1024x748x32bppp
(0x318).
My console lo
On Tue, 27 Jun 2000, you wrote:
> I just built a new system, which happens to be 100%
> SCSI (something I have never attempted before, apparently with good
> reason!). The bios recognizes both 18GB drives as well as the scsi
> cdrom. It boots the install cd, starts the installation, recognizes t
Hello,
In my current kernel 2.2.12, my 10b2 card uses the rtl8139.o
module, but I can't find it in the 2.2.16 "make menuconfig".
Am I just blind, or has something changed?
Sincerely,
Ron
--
+--+
| Ron Johnson, Jr.Home: [EMAIL PROTE
> So after wasting/playing 4 hours trying to understand
> ipchains and correct it to secure it, I've run into a
> problem. I have set ipchains to forward MASQ 192.168.1.0
> and deny everything else... (/etc/rc.d/rc.firewall)
>
> start
> # Needed to initially load modules
> /sbin/depmo
Every time I dial my ISP and the modem makes those horrible noises, the pppd
daemon dies for no apparent reason. Then, if I try again, it connects without
problems. Im' using MDK 7.0, and my ISP's servers use Cobalt Linux.
--
*Guillermo Belli
I am trying to get my radio card to work in 7.0. It worked fine in 6.1.
I keep getting /dev/radiono such device
Although /dev shows the following:
lrwxrwxrwx 1 brianbrian 6 Apr 27 22:24 radio -> radio1
crw--- 1 brianroot 81, 64 Sep 21 1999 radio0
crw---
How about: make config
?
Your LILO config looks okay, but I wouldn't suggest copying a .config file
from one kernel to the next, _especially_ going from 2.2 to 2.4. I've
never tried it myself, but it seems like that's a bad idea; who knows what
config options changed names?
-Matt Stegman
<[EMAI
I'm the guy who whined about not being able to install 7.1 because of
PS/2 port problems. Well, there was a loose connection in my mouse
which was to blame. I apologize for wasting bandwidth and for the ugly
thoughts I had about the authors of the install routine.
All is not well, of course. I h
No problem, just run it. It works.
Dennis/sg
> I have gone to Suns web site and tried to download Staroffice 5.2. I
> click all of the right buttons, and select English Linux (x86) but when I
> get to the end and the software can be dl'd the only file that comes up
> is a .bin file. Is this
James,
I got it working I did not have the right kernel module loaded under
eth0. hehe works like a champ and the boss is happy.
Cheers,
Eric Peters Mail:[EMAIL PROTECTED]
System Admin Network Operations
Inherent Technologies Inc.
offic
> I just built a new system, which happens to be 100%
> SCSI (something I have never attempted before, apparently with good
> reason!). The bios recognizes both 18GB drives as well as the scsi
> cdrom. It boots the install cd, starts the installation, recognizes the
> aic 2940/7980, continues, a
Hmmm, I never had to do that with my install of Mandrake 7.0
-Original Message-
From: Guillaume Rousse [mailto:[EMAIL PROTECTED]]
Sent: Tuesday, June 27, 2000 1:29 AM
To: [EMAIL PROTECTED]
Subject: Re: [expert] KDE2
This page just needs a slight correction for mandrake : you also have t
Swap is on hda2.
On Tue, 27 Jun 2000, you wrote:
> Where's /swap?
>
> Pj
> [EMAIL PROTECTED]
>
>
>
> At 09:46 PM 6/26/00 -0500, you wrote:
> >Using 7.1, I downloaded the new 2.4.0-test2 kernel and it compiled it with
> the
> >default 2.2.16 .config file from the 7.1 distribution. When I t
OH!! My bad - you're the one corresponding with Civilme on UDMA66, yes?
Me thinks you're in good hands, Mike
> I am sorry...I should havce changed the subject line...I was responding to
> someone with a laptopbut I am getting desperate here...LOL
>
> Jim
>
>
> > Hey Jim,
> > I'm not an 'exp
On Wed, 28 Jun 2000, you wrote:
> Hi,
>
> I've got a WD136BA hard disk on my hpt366 controller. If I try to use
> DMA for disk access, my system freezes. This problem didn't exist with
> Mandrake 7.0, but it appeared when I installed 7.1. I tried to upgrade
> my bios. Nothing changed. After that,
"Jim P." wrote:
>
> Civileme
> for the sake of experiment I completely removed the maxtor drive from the
> mix, unplugged both power and ribbon cable and removed it from the bios and
> reset the bios. You guessed it same problemthe only drives in the mix
> right now are the cdrw, Western Dig
On Thu, 29 Jun 2000, you wrote:
> I am wondering what the normal speed for UDMA66? I just got about
> 14M/second, as fast as UDMA33.
What do you mean with "normal-speed"?
What are the normal speeds of a 5-lane and a 3-lane highway? I dunno.. it
depends..
A drive that only supports ATA/33 which
yes I did yet ANOTHER INSTALL grrr! I saw after it posted I didn't say
that I had done it...what was that 907 908 LOL I can install
Mandrake 7.1 in my sleep now...
my problem is that I don't understand why all the equipment works perfectly
in other distros and versions.and not
Civileme
for the sake of experiment I completely removed the maxtor drive from the
mix, unplugged both power and ribbon cable and removed it from the bios and
reset the bios. You guessed it same problemthe only drives in the mix
right now are the cdrw, Western Digital 10.1 gig and my 1.44 3 1
Dave Lers wrote:
> On Fri, 30 Jun 2000, Civileme wrote:
> > But we
> > DO have a 7.1 issue as well... It is not loading in ide-scsi.o UNLESS supermount
>is
> > enabled.
>
> FWIW, From my temp install on a box with a burner I rememder there was an
> ide-scsi line in lilo/grub conf.
Yes, but no
The drive that i am using is fat 32. Iam mounting manually. Can you
help
Calvert
Computer Mall Inc, for all your computer needs and more if we don't have
it we'll order it within 5 working days.
784-485-6137 phone or fax 784-485-6586
Kingstown
St Vincent
__
The present drive is using fat32 and i am mounting manually
how can you help.
Calvert
Computer Mall Inc, for all your computer needs and more if we don't have
it we'll order it within 5 working days.
784-485-6137 phone or fax 784-485-6586
Kingstown
St Vincent
__
Hello,
I am running Mandrake v7.0 and have recently upgraded to the kernel
2.2.17-0.5. I am having problems with swapping and the following error:
VM do_try_to_free_pages failed for kswapd...
This error is causing xwindows to shutdown when loading large
applications. I have more than enough s
On Fri, 30 Jun 2000, Civileme wrote:
> But we
> DO have a 7.1 issue as well... It is not loading in ide-scsi.o UNLESS supermount is
> enabled.
FWIW, From my temp install on a box with a burner I rememder there was an
ide-scsi line in lilo/grub conf.
Ok I'll try, I can even edit the file by hand :)
( have done it in a couple of other installations successfully ).
I think I've done it before in this (my) machine since the new card
came in but can't tell for sure as I tried many things
whithin the scope of my knowledge ( not much ).
But the
I've never used this drive, but are you mounting manually or is supermount
handling this? Are you sure it is mounting with the correct filesystem type?
What file system types do these drives use? Can I format a type using any FS
I want? (ext2fs, fat16, fat32, hpfs, ntfs, etc.)
-Original Mess
hi thank you very much
but i have sorted out the problem already
perhaps you can help me with this one
I am installing my Ls120 drive on my computer under linux 7.0 release 15
and is having quite some fun with the thing. I am able to access the
drive through hdb but is unable to view the fil
the problem you are having is a result of thee resolutioon of the monitor
try xf86config and change the resolution on the monitor you will have to
go through various steps so be careful what you change and do at this
point.
tell me what happens then
Computer Mall Inc, for all your computer nee
Ken Thompson wrote:
> On Thu, 29 Jun 2000, you wrote:
>
> =
> [root@speedy /root]# lspcidrake
> Acer Laboratories Inc. [ALi]|M1541 (unknown unknown)
> Acer Laboratories Inc. [ALi]|M5243 (unknown unknown)
> Acer Laboratories Inc. [ALi]|M5237
- Original Message -
From: "TO. Wilderman Ceren" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Friday, June 30, 2000 8:51 AM
Subject: a question
what i doing for setup SSL in my pop3 service.., i have (GNU POP3 daemon).
yesterday i active it the last stable kernel-2.2.17-0.5mdk
It may be as simple to fix as just opening the /etc/ppp/options file and adding
"noauth" without the quotes. Save and close the file and give it a try.
You may need to comment out the "lock" entry as well..
On Thu, 29 Jun 2000, you wrote:
> Calvert, looks like possibly some DNS info is missing on
"Jim P." wrote:
And as a P.S. to my last message, in order to test the configuration, you will
need to install AGAIN But it does make a weird kind of sense--big change
between 7.0 and 7.1 relative to IDE was the out of the box UDMA66 support--a
code development that would demand performance
I have an answer but you aren't going to like it.
http://kt.linuxcare.com/kt2214_54.epl 2nd item
Try moving (physically)the /dev/hdb to /dev/hdd. We need to get the disks on
separate channels. If that cures the problem, then we know it is the same
phenomenon. I BTW have independently
On Thu, 29 Jun 2000, you wrote:
>
> Is there a way to assign an IRQ to a PCI NIC. PnP OS is disabled, but I can't get
>the NICs' IRQ recognized / assigned.
>
Yes, open DrakConf, Network, Basic Host Information and click on the "adapter"
tab. You can assign IRQ, I/O and device type there.
-
On Thu, 29 Jun 2000, you wrote:
> "Jim P." wrote:
>
> > David Mihm wrote:
> >
> > > On Thu, 29 Jun 2000, root wrote:
> > > [ SNIP ]
> > > > [root@localhost bin]# cat /usr/bin/lspcidrake
> > > > #!/usr/bin/perl
> > > >
> > > > use lib qw(/usr/lib/libDrakX);
> > > >
> > > > use commands;
> > > > co
Don wrote:
>
> OK, When the Blue High Point BIOS screen shows, Does your Drive show
> " Mode 4" ? If not then your Hard Drive is not configured correctly.Western
> Digital Drives work very well with the BP6 mainboard when set properly.
> Western Digital provides a floppy disk to set the drives
OK, When the Blue High Point BIOS screen shows, Does your Drive show
" Mode 4" ? If not then your Hard Drive is not configured correctly.Western
Digital Drives work very well with the BP6 mainboard when set properly.
Western Digital provides a floppy disk to set the drives in UDMA66 mode.
M
John Aldrich wrote:
>
> On Thu, 29 Jun 2000, you wrote:
> > Hi Jon
> > I have a problem can you help. I have set up my internet. Modem is set
> > up but netscape refuses to connect to the internet. It is not seeing the
> > modem, also i can connect to the internet but cannot browse the ne
On Thu, 29 Jun 2000, you wrote:
> sorry I didn't completely think out my answerhow do you run md5sum on the
> copy? this particular copy is about a week old.
>
md5sum md5sums (D/L the md5sums file from the FTP site that you D/L
the ISO from)
>
> I am running a cable modem so it is only about
Add "debug" to your /etc/ppp/options and then check /var/log/messages...
Pierre
Guillermo Belli wrote:
>
> Every time I dial my ISP and the modem makes those horrible noises, the pppd
> daemon dies for no apparent reason. Then, if I try again, it connects without
> problems. Im' using MDK 7.0
On Thu, 29 Jun 2000, you wrote:
> Hi Jon
> I have a problem can you help. I have set up my internet. Modem is set
> up but netscape refuses to connect to the internet. It is not seeing the
> modem, also i can connect to the internet but cannot browse the net. I
> am usin Linux mandrake 7
Klar Brian D Contr MSG/SWS wrote:
>
> I don't know, but I thought you needed to use
> /dev/sr0 for a CDRW, I had to. And insmod ide-scsi.o
>
> Thats the only way my CDRW would work.
This is true for _burning_, i.e. for _writing_ with
the CD-RW.
For _reading_ OTOH, you can perfectly well use th
> Andy Judge wrote:
>
> Is there a way to assign an IRQ to a PCI NIC. PnP OS is disabled, but
> I can't get the NICs' IRQ recognized / assigned.
It depends on your BIOS. Some of them allow to assign manually a
specific
IRQ to a given PCI slot. But you have to know exactly what you are
doing,
be
I don't know, but I thought you needed to use
/dev/sr0 for a CDRW, I had to. And insmod ide-scsi.o
Thats the only way my CDRW would work.
-Original Message-
From: Jim P. [mailto:[EMAIL PROTECTED]]
Sent: Friday, June 30, 2000 7:38 AM
To: [EMAIL PROTECTED]
Subject: Re: [expert] Attn: Civ
Andy Judge wrote:
> Is there a way to assign an IRQ to a PCI NIC. PnP OS is disabled, but
> I can't get the NICs' IRQ recognized / assigned.
they get assigned automagically by the PCI controller.
--
Joseph S. Gardner
Senior Designer / Technical Support
Kirby Co., Cleveland, OH
[EMAIL PROTECT
- Original Message -
From: "Civileme" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Thursday, June 29, 2000 8:55 PM
Subject: Re: [expert] Attn: Civileme
> "Jim P." wrote:
>
> > Civileme wrote:
> >
> > > "Jim P." wrote:
> > >
> > > > see bottom for latest output
> > > >
> > > > Civil
Bill Shirley ha escrit:
> I don't see anything wrong with your share, but I don't understand it
> either. If "produ" is the only user that can access this share, why worry
> about user and group attributes?
Well, it's a bit complicated. I will try to explain the situation. I have a
linux box th
I came in on the tail end of this so I don't know if this pertains to your problem
or if I'll be of much help.
I'm running LM 6.1 with Samba 2.07 and could access the Linux box fine from my
wifes Win95 machine but couldn't access it from my Win98 system. I forgot that the
encryped password settin
-BEGIN PGP SIGNED MESSAGE-
A customer just brought a Celeron machine.. 266Mhz.,. they have been using
it for six months without problems. It has one IDE, one floppy, one PCI VGA
card, and 256M of RAM.
I stuck in the Mandrake 7.1 CD, chose CUSTOMISED and then it said:
"DrakeX will now att
Hi,
To answer your questions about my configuration:
ABIT BP6 with HPT366 onboard
2xCel466 (not overclocked)
64MB SDRAM PC100
ATI Mach64 (quite old)
3DFx Voodoo2
Ethernet PCI 10/100 Realtek 8139
SB PCI 128
Modem ISA 56k
CDROM Actima 50x on hda
CDRW Creative 2224 on hdc
WD136BA 7200rpm on hde
Ph
59 matches
Mail list logo
