Re: sgi 02 latest snapshot CD37.iso boot problems

Please reread the current INSTALL.sgi again, in particular the section on Booting from CD-ROM installation media. It should no longer be necessary to enter the Command Monitor to boot from CD-ROM; just choose Install System Software from the System Maintenance Menu. Mark

iMac G5 booting from its interbal SATA disk

A driver for the K2 SATA controller found in the Apple iMac G5 was just committed to the tree. This means that almost all built-in devices are now supported and my iMac now boots multi-user from its internal SATA disk. There are still some issues to be solved, like support for the built-in power

OpenBSD/hppa

Over the last few weeks I've made some important improvements to the OpenBSD/hppa port. Support for newer B/C/J-class workstations was added, and basically anything but the C8000 should just work. I've also fixed a rather critical bug, which makes machines with a PA-7200 CPU usable again (and

Re: OpenBSD/hppa

From: J.C. Roberts [EMAIL PROTECTED] Date: Wed, 8 Aug 2007 02:33:33 -0700 On Tuesday 07 August 2007, Mark Kettenis wrote: Over the last few weeks I've made some important improvements to the OpenBSD/hppa port. Support for newer B/C/J-class workstations was added, and basically anything

Re: OpenBSD/hppa

advice on a good one to acquire? leads on where to acquire them and for how much would also be welcome since they don't exactly pop up all over the place when googling. best regards, jake Jake, Robert, Hi Jake, Mark Kettenis is a better person to ask and I've cc'd him. Also, folks

Re: problem sata with asus m2v-mx motherboard

Hi Benoit, This line in your dmesg: pciide1: using irq 15 for native-PCI interrupt is highly suspicious, especially since your machine also has pciide0. Can you send me dmesg for the following cases too: GENERIC with acpi enabled GENERIC.MP GENERIC.MP with acpi enabled and the output of #

Re: arc0: unable to query firmware for sensor info

Looking at you acpi-enabled GENERIC.MP dmesg, there are a lot of scary messages: acpimadt0: unknown apic structure type ff acpimadt0: unknown apic structure type ff acpimadt0: unknown apic structure type ff acpi device at acpi0 from table OEMB not configured acpi device at acpi0 from table

Re: sgi 02 R5K irix 6.3 4.3 unsuccessful installation

From: Roger Neth Jr [EMAIL PROTECTED] Date: Wed, 20 Jul 2005 11:57:04 -0700 Went to the SGI O2 command monitor and input boot -f dksc(0,4,8) What happens if you try boot -f dksc(0,4,8)/boot On my system that loads the bootloader from from cdrom and then continues to load the

Sun Fire V215/V245 support

I just committed the final bits that make the Sun Fire V215 and V245 fully supported in 4.1-current. These machines have a PCIe host bridge, supported by the new pyro(4) driver. Writing this driver was the biggest challange, since Sun doesn't provide any documentation for it. So it took some

dual g4 needed for hackathon

On this years hackathon I'd like to hack more on macppc smp support. For obvious reasons I cannot bring my own machine. Is there anyone in the Calgary or Edmonton area that can loan us a dual g4 machine end may/early june? Mark

Re: Big stack HUGE coredump

Date: Sat, 23 Feb 2008 13:58:55 + From: Alexander Nasonov [EMAIL PROTECTED] Hi, If I set a core limit to unlimited and a stack limit to 32768, then run a program with indefinite recursion, the system would generate 8G coredump file. Does the attached diff fix your problem? Index:

Re: Help installing on a Sunfire 280R

Looks like the isp(4) driver doesn't actually support the ISP10160: isp1 at pci3 dev 4 function 0 QLogic ISP10160 rev 0x06: ivec 0x200 data error type 32 sfsr=808008 sfva=f009681d afsr=100800 afva=7ffed0010f0 tf=0x1c08d80 panic: data fault: pc=1162dd0 addr=f009681d sfsr=808008TM,PRIV

Re: Help installing on a Sunfire 280R

Date: Sun, 13 Apr 2008 14:41:48 -0700 From: Don Fanning [EMAIL PROTECTED] Did exactly as described (altering for my settings which were 21 for sbus and 22 for pci). Here is what I currently get: luphy3 at hme2 phy 1: LU6612 10/100 PHY, rev. 1 Sun PCIO EBus2 rev 0x01 at pci1 dev 3

3.9 on nForce4 based amd64 systems

Hi All, Over the last couple of months we have learned that many dual core AMD Athlon64 X2 and AMD Opteron systems using nVidia's nForce4 chipset come with a broken MP BIOS implementation. As a result, they will not work with the bsd.mp kernel. For some of these systems, a BIOS update is

Any people with a W83781D lm(4)?

If you have this lm(4) variant, can you please mail me the output of sysctl hw.sensors? I'm trying to resolve an issue where the data sheet is unclear, and seeing some output from the real world will probably help me solve it. Mark

Re: ichiic0: errors on MP (Sorry about the no subject post!)

As anyone seen this? No matter what I do I cant stop this from happing. I am at the point of being forced to use another OS that I DONT want to use. Any help would be very much appreciated. As a workaround you could disable ichiic in the kernel config. Use man config for hints on how to

New Marvell/SysKonnect PCI-X GigE NIC needed for driver development

I'm working on a driver for the newer Yukon-2 sk(4) variants. I've made some progress on the hardware in a Mac mini, but I really need a card that I can plug into a box that has a normal keyboard and/or serial console. The PCIe variants are of no use to me unless they come with a machine to plug

New Marvell/SysKonnect Gigabit driver

Last night I checked in a driver, msk(4), for the previously unsupported Marvell and SysKonnect Gigabit NICs. The driver works pretty well for me on the new Mac mini, but could really use some more testing, especially on different hardware. If you have such hardware please compile yourself a

Re: New Marvell/SysKonnect Gigabit driver

Date: Thu, 17 Aug 2006 20:58:08 -0400 From: Mike Erdely [EMAIL PROTECTED] Mark Kettenis wrote: Last night I checked in a driver, msk(4), for the previously unsupported Marvell and SysKonnect Gigabit NICs. I couldn't wait to get home! I downloaded the latest snapshot (today's from

Re: amd64 bsd.mp keyboard problems

Rob Sessink wrote: I am having a strange problem with the bsd.mp kernel om my amd64. When i boot openbsd i get problems with the keyboard. When holding down a key for say 2 to 3 seconds it hangs and keeps issuing the pressed key. This leads to all kind of usability problems. This issue

Re: openBSD 3.9 on hp/comapq proliant 8000

Hi Czeslaw, Can you try the attached patch? You'll have to do a make in sys/dev/pci after you've applied the patch. Index: dev/pci/pcidevs === RCS file: /cvs/src/sys/dev/pci/pcidevs,v retrieving revision 1.1139 diff -u -p -r1.1139

Blade 1000

I got the Blade 1000 today. Many thanks to those who made this possible, especially Bret, who got the ball rolling. This should help me finish the work of getting UltraSPARC-III running at full speed. I just installed the latest snapshot on it, so you all can see what you got me. Thanks again,

Re: Marvell Yukon 88E8053 on Apple Mac mini (hanging system)

I saw that someone made the Marvell Yukon NIC on an Intel Mac mini work by activating ACPI in the kernel using NetBSD (even with a working second CPU core, but of course that's unnecessary as long as the NIC doesn't work...), so I tried the same with OpenBSD, unfortunately with no success so

Re: i386 ACPI enabled MP kernel

is ACPI enabled by default on i386 MP or do i need a diff? No it is not. We're very active working on this stuff right now. If you can't figure out yourself how to get this working, you'll just have to be patient until we enable it in GENERIC adn/or GENERIC.MP. Mark

SPARC64-V support

As of yesterday, OpenBSD/sparc64 has full support for Fujitsu's SPARC64-V processor. As far as I know OpenBSD is the first free operating system that supports this processor. These processors are found in Fujitsu's PRIMEPOWER machines. The work was done on a PRIMEPOWER 250, so that model is

Re: ati(4) not working on 4.4-beta sparc64

Hey misc@, I seem to be unable to get accelerated X running on my old ultra 5, unaccelerated just works(tm). Am I missing something? Did I find something? Jasper, Can you post the output of pcidump -v for that Ultra 5? Thanks, Mark

Re: ati(4) not working on 4.4-beta sparc64

Can you try building a kernel with the attached diff? Index: vgafb.c === RCS file: /cvs/src/sys/arch/sparc64/dev/vgafb.c,v retrieving revision 1.52 diff -u -p -r1.52 vgafb.c --- vgafb.c 23 Mar 2008 12:10:53 - 1.52 +++

Poor performance with gem(4)? (reposted from ppc@)

Getting quite decent performance on my Mac mini G4: gem0 at pci2 dev 15 function 0 Apple Uni-N2 GMAC rev 0x80: irq 41, address 00:0d:93:60:dd:1a bmtphy0 at gem0 phy 0: BCM5221 100baseTX PHY, rev. 4 With an msk(4) at the other end and a decent gigabit switch in between, iperf tells me I'm

Re: msk(4) with SK-9S91: Can not set 1000baseSX Single Mode Fiber Media Type

Hi Rolf, Most likely something is not quite right with the eephy(4) driver. The 88E1112 PHY apparently supports both copper and fiber, and I think it should automatically switch over to fiber, but apparently it doesn't. Could you test some diffs for me on that machine? Mark

Re: msk(4) with SK-9S91: Can not set 1000baseSX Single Mode Fiber Media Type

Can you try the attached diff? It has some debug printf's in there, so please send me a dmesg. Regarding the high interrupt load on the v210; try disconnecting the CD-ROM/DVD-ROM. Index: mii/eephy.c === RCS file:

Re: Performance problems with bge under OpenBSD4.0/i386

From: Pete Vickers [EMAIL PROTECTED] Date: Wed, 14 Feb 2007 13:33:25 +0100 # ifconfig bge0 bge0: flags=8843UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST mtu 1500 lladdr 00:17:a4:45:f5:25 groups: egress media: Ethernet autoselect (1000baseT full-duplex)

Improved sparc64 support

OpenBSD 4.0 brought support for UltraSPARC-III processors. Unfortunately that support was not complete and we had to disable the L1 data cache on the cpus. Over the last few months we made significant improvements to the code that made it possible to fully enable the UltraSPARC-III on-chip

Re: Random crashes with Intel D945GCLF2

I just committed a fix for the dmesg corruption problem. This may also fix the random crashes you were saying. Current snapshots should already have the fix. Boy, those Intel-branded boards have shitty BIOSes...

Re: i386 current crashes on boot

Date: Mon, 06 Jun 2011 11:13:12 +0100 From: Nigel Taylor njtay...@asterisk.demon.co.uk On 06/05/11 11:22, Nigel Taylor wrote: Hi, I rebuilt GENERIC.MP from cvs (current 4th June 2011). This crashed on boot. I reverted to old bsd.mp from April this booted. I downloaded bsd.mp from a

Re: fresh Thinkpad x220 - possibly new iwn variant

Date: Mon, 29 Aug 2011 11:53:02 +0200 From: Tomas Bodzar tomas.bod...@gmail.com On Sun, Aug 28, 2011 at 9:38 AM, Tomas Bodzar tomas.bod...@gmail.com wrote: On Sun, Aug 28, 2011 at 2:53 AM, Jonathan Gray j...@goblin.cx wrote: On Sat, Aug 27, 2011 at 09:38:31PM +0200, Peter N. M. Hansteen

Re: Cannot Boot with Intel D201GLY Motherboard [dmesg, fdisk, disklabel]

Date: Sun, 5 Jul 2009 07:30:58 -0400 From: Hendrickson, Kenneth khend...@harris.com Unfortunately I cannot see your attachments.. as the lists do not permit them. I will post them in this message. However, I cannot post OpenBSD.PBR because it is a binary file. As this is a strictly

Re: azalia0 at pci0 dev 20 function 2 ATI SBx00 HD Audio rev 0x00: can't map device i/o space

mem address conflict 0xd0608000/0x4000 Your BIOS is a bit crappy; no surprises there! 0:20:2: ATI SBx00 HD Audio 0x: Vendor ID: 1002 Product ID: 4383 0x0004: Command: 0006 Status ID: 0410 0x0008: Class: 04 Subclass: 03 Interface: 00 Revision: 00 0x000c: BIST: 00

multi-card X: hardware neeeded

Hi Folks, I'm working on makeing multi-card X work again on OpenBSD. I'm making progress, but in order to finish this project, I could really use some hardware. What I need is a PCI graphics card (genuine PCI, not AGP or PCIe) that is well supported by X, preferable something supported by the

Re: May 26 Current on Lenovo SL410 Laptop

OpenBSD 4.7-current (GENERIC.MP) #2: Thu May 27 11:46:17 CEST 2010 r...@polymnia.joachimschipper.nl:/usr/src/sys/arch/amd64/compile/GENERIC.MP real mem = 2003517440 (1910MB) avail mem = 1936490496 (1846MB) mainbus0 at root bios0 at mainbus0: SMBIOS rev. 2.5 @ 0xe0010 (44 entries)

RouterBOARD RB600A support

I recently finished the support for the MicroTik RouterBOARD RB600A by giving OpenBSD/socppc a miniroot image that one can simply write to Compact Flash and stick onto the board. Detailed instructions have been added to INSTALL.socppc. All essential hardware on the board is now supported (with

Re: unidentified system load

It's worth trying to disable ichiic(4).

Cardbus laptop wanted in the Netherlands

So the biggest thing that's still missing in in the acpi suspend/resume code is CardBus (and to a lesser extent PCMCIA) support. My CardBus laptop died two years ago, so I don't really have something to hack on, and makes this work. If somebody in the EU has an old ACPI laptop with CardBus

Re: Dell R310 - H200 Raid performance problem

Date: Sun, 20 Feb 2011 19:54:21 +1000 From: David Gwynne l...@animata.net how to manipulate write cache policy? the lsi firmwares dont implement handling of the mod page changes unfortunately. you could call the ioctl this implements yourself though from userland. David, while I think

Re: Dell R310 - H200 Raid performance problem

Date: Sun, 20 Feb 2011 07:03:25 -0500 From: Kenneth R Westerback kwesterb...@rogers.com On Sun, Feb 20, 2011 at 12:39:06PM +0100, Mark Kettenis wrote: Date: Sun, 20 Feb 2011 19:54:21 +1000 From: David Gwynne l...@animata.net how to manipulate write cache policy? the lsi

Re: Sun Netra X1 still get dc0: watchdog timeout and crash on current

Daniel, Can you try this diff? It won't get rid of the watchdog timeout, but hopefully it will prevent the DMA error. Index: dc.c === RCS file: /cvs/src/sys/dev/ic/dc.c,v retrieving revision 1.116 diff -u -p -r1.116 dc.c --- dc.c

Re: Sun Netra X1 still get dc0: watchdog timeout and crash on current

Date: Fri, 04 Mar 2011 07:40:59 -0500 From: Daniel Ouellet dan...@presscom.net I get pretty much a symetric traffic of ~43.5Mbps each direction using tcpbench as before. Then after may be one minute, both side will cut off oppose to before when only one side was doing that. It will then

Sun Ultra 2

To improve X support on sparc64, I could really use an SBus-based workstation. A dual Ultra 2 would be really great (to be able to test SMP support on these machines), but a single CPU Ultra 2 or Ultra 1 would work as well. Thanks, Mark

Re: Sun Ultra 2

Date: Mon, 16 Feb 2009 09:01:48 +0100 From: Johan SANCHEZ joha...@free.fr Hi Marc, To improve X support on sparc64, I could really use an SBus-based workstation. A dual Ultra 2 would be really great (to be able to test SMP support on these machines), but a single CPU Ultra 2 or Ultra

Re: European orders

I've not been to many OpenBSD events in Europe, but at most of the ones I attended, I've been behind Wim's booth, selling OpenBSD merchandise to help the project. The thing we sold most were T-shirts, and Wim made everyone believe that by buying T-shirts they would financially support the

Dell D531 : Mem conflict + pcmcia not responding

I just committed a diff that may help your machine (although perhaps not with the wi(4)). Should be on your favourite anoncvs mirror in a couple of hours, or in the snapshots in a couple of days.

Re: Watchdog timeout reset in 5.1 on intel nic:s

Problem seems to be found A change of int intr_shared_edge; to int intr_shared_edge = 1; in i386/machdep.c plus kernel recompile solves the problem. Can you post the dmesg of this fixed kernel?

Re: Watchdog timeout reset in 5.1 on intel nic:s

From: =?iso-8859-1?Q?Per-Olov_Sj=F6holm?= p...@incedo.org Date: Wed, 23 May 2012 11:27:34 +0200 On 23 maj 2012, at 10:14, Mark Kettenis wrote: Problem seems to be found A change of int intr_shared_edge; to int intr_shared_edge = 1; in i386/machdep.c plus kernel recompile

Re: azalia audio: Sound distorted

Does the diff below fix the problem? Index: azalia.c === RCS file: /cvs/src/sys/dev/pci/azalia.c,v retrieving revision 1.200 diff -u -p -r1.200 azalia.c --- azalia.c10 May 2012 22:46:48 - 1.200 +++ azalia.c10 Aug

Re: OpenBSD/iwn(4) support for WPA2/PEAP/MSCHAPv2?

Erling Westenvik erling.westenvik at gmail.com writes: I need to connect my ThinkPad T500 running 5.2 current to the wifi network here at my university. E.g. the eduroam network which is available at most universities through, at least, Europe. After Googling around for a while I'm not sure

Re: FAQ 11.1.2 outdated? (framebuffer support)

11.1.2 - Can I have any kind of graphics without X? Assuming you won't accept ASCII graphics, that requires some kind of framebuffer console driver. Some operating systems provide this, but there is not currently one for OpenBSD, nor is there much interest among developers for one.

Re: radeondrm errors (amd64) - Hoping bad things won't really happen

Hi Scott, drm: initializing kernel modesetting (RS690 0x1002:0x791E 0x1458:0xD000). radeondrm0: VRAM: 128M 0x7800 - 0x7FFF (128M used) radeondrm0: GTT: 512M 0x8000 - 0x9FFF drm: PCIE GART of 512M enabled (table at 0x052B1000). error:

Re: Radeondrm firmware update on first boot

I think the driver should somehow refrain from doing KMS on first boot, or the machine should automatically reboot after fw_update to prevent this from happening. That's the intention. The idea is that if firmware is needed, but not present, radeondrm(4) will detach and vga(4) will attach.

Re: adding entropy from the Neug random number generator

I have been looking at the Neug random number generator. This is a $40 minimalist STM32F103 board from Japan that can be flashed with open source firmware to operate as a openPGP token (called Gnuk) or a RNG (Neug). http://www.seeedstudio.com/wiki/FST-01

Black screen after 5.5/macppc install

Hi, after installing OpenBSD 5.5/macppc on my emac I am unable to get a console to display on my monitor. The installer completes succesfully, I can reboot to the new system but the display conks out after the radeon-related kernel messages. I can log in via ssh and my previous install of

Re: Ethernet configuration problem

jmphy0 at jme0 phy 1: JMP211 10/100/1000 PHY, rev.1 What does ifconfig jme0 media print?

Re: Compiling a modern version of Amanad on OpenBSD 5.5

It is a great shame that a package which was originally famous for compling and running on virtually everything that looked vaugely *NIX like has been pushed by the comercail vendor who has come to dominate he development of this package into something that is very dependent on may Linux

Re: Dell R630 high interrupts on acpi0

Date: Tue, 16 Dec 2014 15:16:58 +1000 From: Jonathan Matthew jonat...@d14n.org On Sun, Dec 14, 2014 at 06:22:37PM +0100, Hrvoje Popovski wrote: Hi all, I have got two new Dell R630 and have current on them from Sun Dec 14 15:07:17. Installation went great and very fast. The problem

Re: Dell R630 high interrupts on acpi0

Date: Tue, 16 Dec 2014 21:34:29 -0800 From: Philip Guenther guent...@gmail.com R620 have similar settings and can't see C states in dmesg acpicpu0 at acpi0 That's either insane, or a bug in our acpicpu code, IMO. Probably just the effect of the BIOS not advertising C states at all.

Re: Dell R630 high interrupts on acpi0

Date: Fri, 19 Dec 2014 23:41:56 +1000 From: Jonathan Matthew jonat...@d14n.org On Thu, Dec 18, 2014 at 11:14:54PM +0100, Frederic Nowak wrote: Hi! The diff for extracting memory ranges from ACPI was obviously not tested with ACPI disabled...so we definitely have to check if the

Re: OpenBSD and disk slowliness

The way OpenBSD/i386 uses the xAPIC interrupt controller gives KVM (and other virtualization software) a hard time. OpenBSD/amd64 does things in a KVM-friendlier way, and we're trying to make it even friendlier. Fixing the interrupt handling on OpenBSD/i386 isn't very high on my priority list.

Re: Panic: malloc: out of space in kmem_map

Date: Sat, 4 Apr 2015 11:30:24 +0200 From: Evgeniy Sudyr eject.in...@gmail.com Sorry for delayed answer, I did both before: show uvmexp https://www.dropbox.com/sh/dwmjt7wwunhk5gb/AABTdTS98GLF2vRN56mn6knpa/Screen%20Shot%202015-04-02%20at%2011.37.20.png?dl=0

Re: Panic: malloc: out of space in kmem_map

Date: Thu, 2 Apr 2015 13:16:12 +0200 From: Evgeniy Sudyr eject.in...@gmail.com Hi all, On -stable with patches installed on Supermicro server, got Panic: malloc: out of space in kmem_map. This is first time this panic happened. On this server haproxy and bgpd were running where

Re: Exploiting PCI-based DMA in OpenBSD

All this is true and I totally agree with you. But there are partial workarounds against this attack (see Windows/MacOS). All I wanted to know whether there were any work in this direction. I'm not a programer. It is impossible for me to answer to yourself by studying commits to CVS. An

Re: possible httpd Content-Length overflow

The problem seems to be either low-memory or i386 related. I tested on an amd64 machine with 3GB RAM, and the problem goes away with 2+ GB files. Does the diff below fix the issue? Index: httpd.h === RCS file:

Re: can't wake from zzz

It does not power on. This laptop is very quiet when running OpenBSD, most of the time I don't know if fan rotates or not, but I guess it does not start after pressing power button in suspended state. No backlight either. Power button on T440 has green led light, and after going into

Re: GPT vs. MBR

> > I'm now in a upgrading process to OpenBSD 5.8 (backup etc.). I have laptop > > with EFI(UEFI) capability and 500GB HDD. There are any benefits from GPT > > with my configuration to migrate from MBR to GPT (I'm also using full disk > > oencryption)? > > 5.8 doesn't support GPT/UEFI, so it's

em(4) watchdog timeouts

Can those that are experiencing watchdog timeouts check if the diff below gets rid of them? Index: if_em.h === RCS file: /home/cvs/src/sys/dev/pci/if_em.h,v retrieving revision 1.58 diff -u -p -r1.58 if_em.h --- if_em.h 30 Sep

Re: PC Engine APU.1D4 installation stopper.

> > For i386/amd64 you have to tell boot you want serial output > > either at the boot prompt or via boot.conf. > > > > stty com0 115200 > > set tty com0 > > > OpenBSD 5.8 (GENERIC.MP) #1236: Sun Aug 16 02:31:04 MDT 2015 > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP

Re: [SOLVED] Re: X fails to start with latest sparc64 snapshot

Date: Tue, 7 Jul 2015 21:34:54 +0200 From: Markus Lude markus.l...@gmx.de Change from kettenis@ in xenocara/lib/libpciaccess/src/openbsd_pci.c r1.26 fixed it for me. Good to hear that. On Tue, Jun 30, 2015 at 10:20:46PM +0200, Markus Lude wrote: Hello, after upgrading to snapshot

Re: requesting help working around boot failures with supermicro atom board

> # sysctl -a|grep 'sensors.*temp' > hw.sensors.cpu0.temp0=30.00 degC > hw.sensors.lm1.temp0=0.00 degC > hw.sensors.lm1.temp1=14.00 degC > hw.sensors.lm1.temp2=14.00 degC > # reboot > > BEEEP! Oh that is interesting. Can you try disabling the lm(4) driver in your kernel? You can

Re: Suspend Hangs ThinkPad T450s

> From: Aaron Poffenberger > Date: Sun, 20 Sep 2015 16:39:54 -0500 > > Another issue I noted in the ThinkPad dmesg. Pulling out as separate > request for reference sake. > > Suspending now hangs system > - X11 disables correctly and screen goes dark > - Light on power

Re: powerof2()

d: by XS4ALL Virus Scanner > X-XS4ALL-Spam-Score: 0.0 () UNPARSEABLE_RELAY > X-XS4ALL-Spam: NO > Envelope-To: open...@xs4all.nl > > Mark Kettenis wrote on Fri, Sep 25, 2015 at 02:27:52PM -0600: > > > CVSROOT:/cvs > > Module name:src > > Changes b

Re: Add Bay Trail EHCI controller to pcidevs

> acpi0 at bios2: rev 2, ACPI control unavailable The diff below should fix that issue and get rid of the can't map interrupt issues. Index: acpi.c === RCS file: /cvs/src/sys/dev/acpi/acpi.c,v retrieving revision 1.297 diff -u

Re: Boot support for PCIe SSD

Hi Lawrence, > Does OpenBSD support PCIe SSDs? I'm talking about the non-SATA variants > specifically. PCIe SSDs come in (at least two) variants. The ones that implement an AHCI standard controller work. Those that implement the newer NVMe standard don't work yet. In principle the NVMe

Re: Progress on adding support for Perle Speed8 LE

Hi Jordon, Please send future diffs to tech@; misc@ is for trolls ;) > I'm still not sure why the first four ports give the probe message > and the second four don't. If this is adequate testing, feel free > to add this. If more testing is preferred, let me know what to do. The card is

Re: serious watchdog timeout issues with em driver

> Date: Fri, 20 Nov 2015 14:12:52 +0100 > From: Martin Pieuchot > > On 19/11/15(Thu) 17:54, Sonic wrote: > > Have serious problems for over 7 weeks now with em driver, > > specifically any rev of if_em.c > 1.305. Starting with rev 1.306, > > released on 2015/09/30 and

Re: inteldrm(4) display corruption on MacBook

Hi Ossi, Your digging: > I went digging what produces the error > > error: [drm:pid0:inteldrm_attach] *ERROR* failed to init modeset > > and it looks like in sys/dev/pci/drm/drm_irq.c:1.66 > > drm_irq_install() calls > > if (drm_dev_to_irq(dev) == 0) > return -EINVAL; >

Re: anyone using msk(4) NICs?

I have one that works fine: mskc0 at pci1 dev 0 function 0 "Marvell Yukon 88E8053" rev 0x22, Yukon-2 EC rev. A3 (0x2): apic 1 int 16 But there are several variants of this chip, and some are buggier than others. Problems have been reported before. Unfortunately I have never been able to

Re: Add Bay Trail EHCI controller to pcidevs

> Date: Thu, 7 Jan 2016 11:08:39 + (UTC) > From: > > Hi Mark, > Thanks for having a look at this. > The 6th of January install59.fs should have v 1.298 of acpi.c > But I still get the same 'can't map interrupt' on both EHCI and XHCI. > Let me know if there's a way to

Re: panic: mtx_enter: locking against myself

> panic: mtx_enter: locking against myself > Starting stack trace... > panic() at panic+0x10b > mtx_enter() at mtx_enter+0x60 > sofree() at sofree+0xa0 > in_pcbdetach() at in_pcbdetach+0x40 > tcp_close() at tcp_close+0xad > tcp_timer_2msl() at tcp_timer_2msl+0x90 > softclock() at softclock+0x315 >

Re: v5.9 fails to boot Wyse Thin client (AMD G-T48E)

> Hello everybody, > > I tried to install OpenBSD v5.9 but as soon as kernel loads > the screen goes black. Cannot enter into UKC> either. > hd0a:5.9/amd64/bsd.mp dropped into debugger with some radeon errors. Without those error messages there is not much we can do for you.

Re: xbacklight / screen brightness

> There are a few instances of this bug. You can also see it with cpu > frequency and audio volume. > > Most drivers maintain soft state that should mirror the hardware > state. Except when it doesn't. Sometimes the driver has a bug, > sometimes the hardware lies, sometimes something else goes >

Re: Dell XPS13 9333 Touchpad doesn't work

Please send bug reports to b...@openbsd.org. > dwiic0 at acpi0: I2C1 addr 0xfe105000/0x1000 irq 7 > iic0 at dwiic0 > ihidev0 at iic0 addr 0x2c irq 39dwiic0: timed out reading remaining 29, > failed fetching initial HID descriptor > "DLL060A" at acpi0 not configured Can you try what happens if

error: [drm:pid10679:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... render ring idle

Please send bug reports, using the sendbug(1), to b...@openbsd.org. Anyway, with: > inteldrm0 at pci0 dev 2 function 0 "Intel HD Graphics 5500" rev 0x09 > drm0 at inteldrm0 > inteldrm0: msi > inteldrm0: 1920x1080 and > [22.013] (II) LoadModule: "intel" > [22.013] (II) Loading

Re: BeagleBone Black GPIO

> Hello Misc, This is probably a discussion for tech@; anyway: > I'm trying to get a BeagleBone Black talking onewire and i2c via GPIO to > several off-board ICs through gpioow(4) and gpioiic(4) respectively. As a warning, let me say that tinkering with hardware like this isn't very high on the

Re: Meltdown, aka "Dear Intel, you suck"

> From: Philip Guenther > Date: Fri, 5 Jan 2018 20:52:20 -0800 > > Unless something unexpected happens, we'll be applying the workaround to > amd64 first and then working out what to do for i386 and arm* (if still > though to be necessary for arm) after that. FWIW, Meltdown

Re: snapshot boot fails with error "entry point at 0x1001000"

Hi Kastus, Please don't have technical discussions on misc@; some developers, like me, only read it sporadically. The tech@ list is a much better place. The problem with your approach is that you allocate memory at a fixed address, and we can't be sure that memory is available. We may have to

Re: gl.inet Brume (GL-MV1000): sdcard works with 6.8 but not -current

Hi Darren, This got broken when Patrick fixed something related to slow mode for the Marvel ARMADA 8040 SoC. The diff below fixes it for me on my Turris MOX which uses the same SoC. Not entirely sure what is going wrong here since looking at the Linux code suggests that Patrick's fix should

Re: gl.inet Brume (GL-MV1000): sdcard works with 6.8 but not -current

> From: Darren Tucker > Date: Sun, 4 Apr 2021 09:18:30 +1000 > > On Sun, 4 Apr 2021 at 01:32, Patrick Wildt wrote: > > [...] > Maybe you both can try my revert and make sure it doesn't introduce any > other regressions? > > That also seems to work on the Brume in question: Works for the

Re: Raspberry Pi 4B performance compared to APU / wireless networking?

> The APU itself doesn't have wlan so that depends on what card you use > of course. bwfm(4) does work well though the antenna is a resonant cavity > etched on the PCB and there's no way to move it outside of the case. > If you want to run a high performance AP you'll still want a separate >

Re: ttyflags hangs on Dell PowerEdge R200

> Date: Mon, 31 Jan 2022 14:03:29 +0100 > From: Jan Stary > > On Jan 26 18:02:17, mark.kette...@xs4all.nl wrote: > > > > revision 1.406 > > date: 2022/01/26 14:39:07; author: kettenis; state: Exp; lines: +2 -2; > > commitid: zL3Ot2UVnkpDz6go; > > An ACPI device

Re: ttyflags hangs on Dell PowerEdge R200

> Date: Mon, 31 Jan 2022 15:41:32 +0100 > From: Jan Stary > > On Jan 31 14:47:41, mark.kette...@xs4all.nl wrote: > > > Date: Mon, 31 Jan 2022 14:03:29 +0100 > > > From: Jan Stary > > > > > > On Jan 26 18:02:17, mark.kette...@xs4all.nl wrote: > > > > > > > >

Re: time keeping fallback mechanics during reboot on octeon

> From: Theo de Raadt > Date: Sat, 13 Jan 2024 07:39:34 -0700 (MST) > > Blocking the timeupdate in ffs_sbupdate() will be difficult. > > It is probably easier to have the BOOT kernel learn the time (from the > true root filesystem), so that ffs_sbupdate() writes back the same > value. > > That

Important message for Apple Silicon OpenBSD/arm64 users

As indicated here: https://social.treehouse.systems/@AsahiLinux/112449204541186432 The system firmware that comes with macOS Sonoma 14.5 triggers a bug in the m1n1 bootloader that is used to boot OpenBSD on these machines. The bug will prevent OpenBSD from booting on some machines after the