My response was to "Blazen" who lately seems to be adding only unconstructive comments like "LAME LAME LAME".
----- Original Message ----- From: "Jason" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Sunday, August 24, 2003 9:38 AM Subject: RE: [smartBridges] Disabling Tabs in SimpleMonitor > Ray, > > With all due respect, I did my research. 6 months ago we were not seeing > these issues. The units were working fine until I "upgraded" the > firmware. > > Why should I not complain about an investment I made months ago that has > ceased to work. Do you suggest I throw the equipment away and start > over? I am not spending my energy complaining - I'm spending my energy > trying to protect my investment. > > I did my ersearch, and I am again doing research - looking into > alternatives, like you said. > > Jason > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED] On Behalf Of Ray > > Sent: Sunday, August 24, 2003 12:31 PM > > To: [EMAIL PROTECTED] > > Subject: Re: [smartBridges] Disabling Tabs in SimpleMonitor > > > > > > You really should look at switching to a different > > manufacturer. You seem to be spending allot of energy > > complaining about what SB doesn't do when you could be > > looking for units that meet your needs. It appears that you > > did not do your research before deciding on equipment. > > > > This is meant as friendly advise and not slam. > > > > Ray > > > > > > ----- Original Message ----- > > From: "Blazen Wireless" <[EMAIL PROTECTED]> > > To: <[EMAIL PROTECTED]> > > Sent: Sunday, August 24, 2003 9:12 AM > > Subject: Re: [smartBridges] Disabling Tabs in SimpleMonitor > > > > > > > HAHA I think its just plain stupid that you cant make all > > your changes > > > on ALL the tabs then hit save and have it take it. But > > what's is so F > > > up > > about > > > it is when you want to say change to one mode or another > > you have to > > > make one change at a time so it requires a truck roll on > > the opposite > > > end. I.E you change from AP mode to client mode and your screwed > > > because you cant change the SSID at the same time etc etc > > Totally not > > > thought out on SB > > part > > > but they will tell you to use their wonderful tool called simple > > > deploy heheh which is just the lamest tool when it comes to > > having set > > > different features to individual radios. This does not work well > > > because you still have to hit the stupid reset button to > > revert back > > > to the default settings should something get hosed up.. > > > > > > There are a lot of wonderful features yet there are some real lame > > > ones > > too > > > this being the biggest. The other one is when logged into the radio > > > via wireless and you want to do a site survey and you hit > > the button > > > it > > reboots > > > the radio! Seems like anything you do reboots the radio > > WHY? who knows > > maybe > > > its because if you don't it will lock up or some strange crap like > > > that. I would love to be able to not have it do that each and every > > > time > > especially > > > if you are trying to keep an eye on the stats and it wipes them out. > > > > > > LAME LAME LAME > > > > > > ----- Original Message ----- > > > From: "Jason" <[EMAIL PROTECTED]> > > > To: <[EMAIL PROTECTED]> > > > Sent: Sunday, August 24, 2003 8:31 AM > > > Subject: [smartBridges] Disabling Tabs in SimpleMonitor > > > > > > > > > I am sooooo upset right now that I can scream. > > > > > > I have two aPPOs set up as AP/client. I currently am at the > > client end > > > of a "PtP" link. I want to switch back to wireless bridge > > mode. There > > > is no way to do this because the Wireless Bridge tab is > > unavailable in > > > SimpleMonitor, and I can't set the MAC address of my local > > aPPO in the > > > remote aPPO's MAC field. I switched to wireless bridge mode on the > > > remote unit, hoping that the MAC address would be stored (since I > > > previously had these two units in wireless bridge mode. > > > > > > This is the dumbest thing I have ever seen. Why should I > > have to visit > > > and physically connect to each aPPO to switch operating modes!!! > > > > > > Now I have to drive an hour to the other end, get into the location > > > (which is not open on Sunday), and physically connect an ethernet > > > cable to the unit. Isn't this "wireless" networking! It seems to me > > > that the tab should not be disabled, and should allow you > > to put in a > > > MAC address and save it before switching operating modes. > > > > > > Jason > > > > > > P.S. If anyone reminds me to bring a crossover cable with me, I'll > > > kick 'em in the nuts. :) > > > > > > > > > The PART-15.ORG smartBridges Discussion List > > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > > > smartBridges <yournickname> To Remove: > > mailto:[EMAIL PROTECTED] (in > > > the body type unsubscribe > > > > > smartBridges) > > > Archives: http://archives.part-15.org > > > > > > > > > The PART-15.ORG smartBridges Discussion List > > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > > smartBridges <yournickname> > > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > > smartBridges) > > > Archives: http://archives.part-15.org > > > > > > > The PART-15.ORG smartBridges Discussion List > > To Join: mailto:[EMAIL PROTECTED] (in the body type > > subscribe smartBridges <yournickname> To Remove: > mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://archives.part-15.org > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://archives.part-15.org > The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
