Hello, I am having no luck getting FreeBSD/amd64 8.2-RELEASE to boot on the Net6501. FreeBSD/i386 8.2-RELEASE works fine, but if possible I'd like to run amd64 in this machine's intended role.
I've seen reports that 64-bit Linux and OpenBSD have been booted
successfully, but not FreeBSD. Has anyone gotten this working?
The kernel initializes as seen below, then it just stops. I've tried
disabling ACPI, APIC, MSI, and MSIX in various combinations. The boot
output changes a bit, particularly with regard to interrupts, but
nothing I have tried has altered where the kernel stops. Also, I don't
seem to be able to break into the debugger.
For the following dmesg, ACPI, APIC, MSI, and MSIX are at defaults.
KDB: debugger backends: ddb
KDB: current backend: ddb
ACPI Error: A valid RSDP was not found (20101013/tbxfroot-309)
Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.2-RELEASE-p2 #0: Thu Dec 1 16:42:39 MST 2011
[email protected]:/usr/obj/usr/src/sys/NET6501 amd64
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Genuine Intel(R) CPU @ 1.60GHz (1600.01-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x20661 Family = 6 Model = 26
Stepping = 1
Features=0xbfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x40e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE>
AMD Features=0x20100800<SYSCALL,NX,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant
real memory = 2147352576 (2047 MB)
avail memory = 2060894208 (1965 MB)
kbd0 at kbdmux0
ACPI Error: A valid RSDP was not found (20101013/tbxfroot-309)
ACPI: Table initialisation failed: AE_NOT_FOUND
ACPI: Try disabling either ACPI or apic support.
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> irq 10 at device 23.0 on pci0
pci1: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> irq 10 at device 0.0 on pci1
pci2: <PCI bus> on pcib2
pci2: <unknown> at device 0.0 (no driver attached)
pci2: <network, ethernet> at device 0.1 (no driver attached)
pci2: <unknown> at device 0.2 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xa0000b00-0xa0000bff irq 9
at device 2.0 on pci2
ohci0: Could not allocate irq
device_attach: ohci0 attach returned 6
ohci1: <OHCI (generic) USB controller> mem 0xa0000c00-0xa0000cff irq 9
at device 2.1 on pci2
ohci1: Could not allocate irq
device_attach: ohci1 attach returned 6
ohci2: <OHCI (generic) USB controller> mem 0xa0000d00-0xa0000dff irq 9
at device 2.2 on pci2
ohci2: Could not allocate irq
device_attach: ohci2 attach returned 6
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xa0000e00-0xa0000eff irq
9 at device 2.3 on pci2
ehci0: Could not allocate irq
device_attach: ehci0 attach returned 6
pci2: <serial bus, USB> at device 2.4 (no driver attached)
pci2: <base peripheral, SD host controller> at device 4.0 (no driver
attached)
pci2: <base peripheral, SD host controller> at device 4.1 (no driver
attached)
ahci0: <AHCI SATA controller> port 0x1020-0x103f mem
0xa0004400-0xa00047ff irq 11 at device 6.0 on pci2
ahci0: unable to map interrupt
device_attach: ahci0 attach returned 6
ohci3: <OHCI (generic) USB controller> mem 0xa0004800-0xa00048ff irq 10
at device 8.0 on pci2
ohci3: Could not allocate irq
device_attach: ohci3 attach returned 6
ohci4: <OHCI (generic) USB controller> mem 0xa0004900-0xa00049ff irq 10
at device 8.1 on pci2
ohci4: Could not allocate irq
device_attach: ohci4 attach returned 6
ohci5: <OHCI (generic) USB controller> mem 0xa0004a00-0xa0004aff irq 10
at device 8.2 on pci2
ohci5: Could not allocate irq
device_attach: ohci5 attach returned 6
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xa0004b00-0xa0004bff irq
10 at device 8.3 on pci2
ehci1: Could not allocate irq
device_attach: ehci1 attach returned 6
pci2: <unknown> at device 10.0 (no driver attached)
pci2: <simple comms, UART> at device 10.1 (no driver attached)
pci2: <simple comms, UART> at device 10.2 (no driver attached)
pci2: <simple comms, UART> at device 10.3 (no driver attached)
pci2: <simple comms, UART> at device 10.4 (no driver attached)
pci2: <unknown> at device 12.0 (no driver attached)
pci2: <serial bus> at device 12.1 (no driver attached)
pci2: <serial bus> at device 12.2 (no driver attached)
pci2: <serial bus> at device 12.3 (no driver attached)
pci2: <unknown> at device 12.4 (no driver attached)
pcib3: <PCI-PCI bridge> irq 11 at device 24.0 on pci0
pci3: <PCI bus> on pcib3
pcib4: <PCI-PCI bridge> at device 0.0 on pci3
pci4: <PCI bus> on pcib4
pcib5: <PCI-PCI bridge> at device 2.0 on pci4
pci5: <PCI bus> on pcib5
em0: <Intel(R) PRO/1000 Network Connection 7.1.9> port 0x2000-0x201f mem
0xa1000000-0xa101ffff,0xa1020000-0xa1023fff irq 9 at device 0.0 on pci5
em0: Using MSIX interrupts with 0 vectors
em0: Unable to allocate bus resource: interrupt
device_attach: em0 attach returned 6
pcib6: <PCI-PCI bridge> at device 3.0 on pci4
pci6: <PCI bus> on pcib6
em1: <Intel(R) PRO/1000 Network Connection 7.1.9> port 0x3000-0x301f mem
0xa2000000-0xa201ffff,0xa2020000-0xa2023fff irq 10 at device 0.0 on pci6
em1: Using MSIX interrupts with 0 vectors
em1: Unable to allocate bus resource: interrupt
device_attach: em1 attach returned 6
pcib7: <PCI-PCI bridge> at device 4.0 on pci4
pci7: <PCI bus> on pcib7
pcib8: <PCI-PCI bridge> irq 5 at device 25.0 on pci0
pci8: <PCI bus> on pcib8
pcib9: <PCI-PCI bridge> at device 0.0 on pci8
pci9: <PCI bus> on pcib9
pcib10: <PCI-PCI bridge> at device 2.0 on pci9
pci10: <PCI bus> on pcib10
em2: <Intel(R) PRO/1000 Network Connection 7.1.9> port 0x4000-0x401f mem
0xa3000000-0xa301ffff,0xa3020000-0xa3023fff irq 10 at device 0.0 on pci10
em2: Using MSIX interrupts with 0 vectors
em2: Unable to allocate bus resource: interrupt
device_attach: em2 attach returned 6
pcib11: <PCI-PCI bridge> at device 3.0 on pci9
pci11: <PCI bus> on pcib11
em3: <Intel(R) PRO/1000 Network Connection 7.1.9> port 0x5000-0x501f mem
0xa4000000-0xa401ffff,0xa4020000-0xa4023fff irq 11 at device 0.0 on pci11
em3: Using MSIX interrupts with 0 vectors
em3: Unable to allocate bus resource: interrupt
device_attach: em3 attach returned 6
pcib12: <PCI-PCI bridge> at device 4.0 on pci9
pci12: <PCI bus> on pcib12
pcib13: <PCI-PCI bridge> irq 9 at device 26.0 on pci0
pci13: <PCI bus> on pcib13
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
cpu0 on motherboard
atrtc0: <AT Real Time Clock> at port 0x70 irq 8 on isa0
atrtc0: Warning: Couldn't map Interrupt.
uart0: <Non-standard ns8250 class UART with FIFOs> at port 0x3f8-0x3ff
irq 4 flags 0x10 on isa0
uart0: console (19200,n,8,1)
Timecounter "TSC" frequency 1600013248 Hz quality 800
Timecounters tick every 1.000 msec
This is where it stops.
Thanks for any help,
-nick
--
[email protected] - all messages cryptographically signed
signature.asc
Description: OpenPGP digital signature
_______________________________________________ Soekris-tech mailing list [email protected] http://lists.soekris.com/mailman/listinfo/soekris-tech
