Hi Henk, A pre-production v8.3 Lite+Xtall receiver kiit was mailed to you on May 9. Hopefully you will soon receive the small padded envelope.
Thanks for the kit order. 73, Tony KB9YIG ----- Original Message ----- From: Henk Keppel To: [email protected] Sent: Monday, May 12, 2008 8:18 AM Subject: Re: [softrock40] RXTX+Xtall v6.3 transceiver Hi Tony, On march 17 I sent $25 with PayPal to Robert Parks at [EMAIL PROTECTED] with the following message: "Hi Tony, Since january 8 I tried to send you this money and it bounced several times. I hope that this time it will bve OK and that you reserved one beta kit off LITEx-Tall plus 3 x BPF for me." Did you get enough money from me as payment for the softrock RXTX +xtall? If not, I can send what I owe you. Did you ship already? Regards, Henk, PA0KEP . ----- Original Message ----- From: Tony Parks To: [email protected] Sent: Monday, May 12, 2008 9:14 AM Subject: Re: [softrock40] RXTX+Xtall v6.3 transceiver Two additional RXTX+Xtall v6.3 transceiver testers are now in place. Thanks and 73, Tony KB9YIG ----- Original Message ----- From: kb9yig To: [email protected] Sent: Sunday, May 11, 2008 4:26 PM Subject: [softrock40] RXTX+Xtall v6.3 transceiver Good Afternoon All, I have completed the board layout for a version of the RXTX where the Xtall function is combined on the same board with a SoftRock Lite receiver, (like the Lite+Xtall v8.3), as well as the one-watt RXTX transmitter function. Plug-in RX and TX modules provide for band changing with the target to be the four band groups: 160m, 80m/40m, 30m/20m/17m, and 15m/12m/10m. The board size is slightly smaller than the RXTXv6.2 board at 2.5 inches by 3.25 inches. The TX module plugs on top of the upper right quadrant of the RXTX board carries the TX band specific components as well as the driver and PA circuits. The receiver band specific module is the same as used with the v8.3 Lite+Xtall kit. One additional feature of the RXTX+Xtall v6.3 board is the inclusion of the Rocky 3.x interface on the board so that the transceiver is Rocky ready, just wire a D-9 connector to the board for serial port control of the RXTX board. Final board checking should be completed by Monday and prototype boards will be orders for four examples of the transceiver kit. I am needing two additional testers who have the interest and test equipment to evaluate the performance of the transceiver on various bands. The kit will be provide at no charge to two testers who are interested in providing feedback later in May. Thanks and 73, Tony KB9YIG -------------------------------------------------------------------------- avast! Antivirus: Inkomende bericht is niet besmet. Virus Gegevensbestand (VPS): 080511-0, 11-05-2008 Getest op: 12-5-2008 9:16:01 avast! auteursrecht (c) 2000-2008 ALWIL Software. ------------------------------------------------------------------------------ Mijn Postvak In wordt beschermd door SPAMfighter 7043 spam-mails zijn er tot op heden geblokkeerd. Download de gratis SPAMfighter vandaag nog! ---------------------------------------------------------------------------- avast! Antivirus: Uitgaande bericht is niet besmet. Virus Gegevensbestand (VPS): 080511-0, 11-05-2008 Getest op: 12-5-2008 14:18:52 avast! auteursrecht (c) 2000-2008 ALWIL Software.
