the problem is i don't see any "username value" should i replace it with the hostname? (before password) and i don't use any router, the ip was there alredy, i didn't change it im using the old one, rev 0.00 i think (green, looks a littlebit like a mouse)
Beso wrote: >i see there is no active chap pap secrets. to do so replace "#xxx >username * password" with: "your username * your password" in both the >files, then make a simbolic link to speedtch in the same directory >with the name "speedtouch". for some reason my suse won't connect >until i made a link to it. To see if the firmware loads, look >carefully at system startup verbose and check if the system loads it. >if you can't see it check the modules loaded at startup and see if it >loaded or not. >anyway, from the verbose that you sent it should be everything ok, >except the secrets of chap and pap, so first try setting them up as >required. >if you're using a router (as i can see from the 192.168.1.1 link) try >to see if your network config is ok. > >ps.anyway what type of seepdtouch are you using???? > >2005/10/10, Franzelot <[EMAIL PROTECTED]>: > > >>pppoatm is loaded (modprobe pppoatm), modem firmware i don't now >>excatly, i have installed it, do i have to do something to load it? >>i am root yes, vpi/vci is 8.48 since i live in austria >>im not sure aubout the user, in the files chap/pap secrets i didn't find >>something where i could enter the username >>i'll show you a copy of the files that i have modified and the error >>message here: >> >># Secrets for authentication using CHAP >># client server secret IP addresses >> >># OUTBOUND CONNECTIONS >># Here you should add your PPP Login and PPP password to connect to your >># provider via pap. The * means that the entry(login and passoword may be >># used for ANY host you connect to. >># Thus you do not have to worry about the foreign machine name. Just >># replace password with your password. >>#hostname * ******* (here my password) >> >># PREDIFINED CONNECTIONS >># These are user and password entries for publically accessible call-by-call >># Internet providers in Germany. If they confict with your config, >>remove them. >># READ_IN_CALLBYCALL_SECRETS >> >># INBOUND CONNECTIONS >>#client hostname <password> 192.168.1.1 >> >> >> >> >> >># Secrets for authentication using PAP >># client server secret IP addresses >> >># OUTBOUND CONNECTIONS >># Here you should add your PPP Login and PPP password to connect to your >># provider via pap. The * means that the entry(login and passoword may be >># used for ANY host you connect to. >># Thus you do not have to worry about the foreign machine name. Just >># replace password with your password. >>#hostname * ******* (pass here) >> >># PREDIFINED CONNECTIONS >># These are user and password entries for publically accessible call-by-call >># Internet providers in Germany. If they confict with your config, >>remove them. >># READ_IN_CALLBYCALL_SECRETS >> >># INBOUND CONNECTIONS >>#client hostname <password> 192.168.1.1 >> >># If you add "auth login -chap +pap" to /etc/mgetty+sendfax/login.config, >># all users in /etc/passwd can use their password for pap-authentication. >># >># Every regular user can use PPP and has to use passwords from /etc/passwd >>#* hostname "" >># UserIDs that cannot use PPP at all. Check your /etc/passwd and add any >># other accounts that should not be able to use pppd! Replace hostname >># with your local hostname. >>#guest hostname "*" - >>#master hostname "*" - >>#root hostname "*" - >>#support hostname "*" - >>#stats hostname "*" - >> >>this is the /etc/ppp/peers/speedtch file: >> >>lcp-echo-interval 10 >>lcp-echo-failure 3 >>noipdefault >>defaultroute >>user '********' >>noauth >>noaccomp >>nopcomp >>noccp >>novj >>holdoff 4 >>persist >>maxfail 25 >>updetach >>usepeerdns >>plugin pppoatm.so >>8.48 >> >>error message when i type pppd call speedtch: >> >>Plugin pppoatm.so loaded. >>PPPoATM plugin_init >>PPPoATM setdevname_pppoatm - SUCCESS:8.48 >>Using interface ppp0 >>Connect: ppp0 <--> 8.48 >>LCP terminated by peer >>Connection terminated. >>connect(8.48): Address already in use >> >> >>i hope this files show you the problem... >> >>@anja, spreche sehr gut deutsch ja :) >> >>Franzelot >> >> >> >> >> >>Beso wrote: >> >> >> >>>are the pppoatm and the modem firmware loaded at startup? if not >>>loaded, you can't use the modem. >>>have you granted root priviledges to all the users? if not the script >>>cannot connect? >>>are the vci/vpi ok?? if not your isp could not grant you access. >>>are the user and pass ok?? if not your isp cannot grant access. >>>try to see if you reply yes to all these questions. if you do so, then >>>remove the drivers and do the procedure once again trying to compile >>>the source and not with the source already compiled. >>> >>>2005/10/9, Franzelot <[EMAIL PROTECTED]>: >>> >>> >>> >>> >>>>Beso wrote: >>>> >>>> >>>> >>>> >>>> >>>>>it should be already connected.... try a link and see if it is really >>>>>connected.... if you've done every single step in the guide it should >>>>>connect at startup, so that is the reason why it says you that the >>>>>address is already in use.... >>>>> >>>>>2005/10/9, Franzelot <[EMAIL PROTECTED]>: >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>>>hi folks! >>>>>>i want to connect to the internet with my speedtouch usb modem >>>>>>i've alredy installed firmware and modified all files told in your how-to >>>>>> >>>>>>when i type pppd call speedtc, i get following message >>>>>>(not exactly these words) >>>>>> >>>>>>LCP conntection terminated >>>>>>connection terminated by peer >>>>>>adress alredy in use >>>>>> >>>>>>what does that mean? >>>>>>and what can i do? >>>>>> >>>>>>thx and greetings >>>>>>Franzelot >>>>>>(sry if my english isn't that good :) >>>>>> >>>>>> >>>>>> >>>>>>Liste de diffusion modem ALCATEL SpeedTouch USB >>>>>>Pour se désinscrire : mailto:[EMAIL PROTECTED] >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>-- >>>>>beso >>>>> >>>>>d-_-b >>>>>Liste de diffusion modem ALCATEL SpeedTouch USB >>>>>Pour se désinscrire : mailto:[EMAIL PROTECTED] >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>no it is definitly not connected,(browser does not work and i can't ping >>>>anything) and i don't want my pc to get connected on boot so i didn't >>>>tell my linux to do so :) because the modem is not always plugged in and >>>>I do not want to be connected to the internet all the time >>>> >>>>lg. >>>>Franzelot >>>> >>>> >>>>Liste de diffusion modem ALCATEL SpeedTouch USB >>>>Pour se désinscrire : mailto:[EMAIL PROTECTED] >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>-- >>>beso >>> >>>d-_-b >>>Liste de diffusion modem ALCATEL SpeedTouch USB >>>Pour se désinscrire : mailto:[EMAIL PROTECTED] >>> >>> >>> >>> >>> >>> >>> >>> >>> >> >>Liste de diffusion modem ALCATEL SpeedTouch USB >>Pour se désinscrire : mailto:[EMAIL PROTECTED] >> >> >> >> >> > > >-- >beso > >d-_-b >Liste de diffusion modem ALCATEL SpeedTouch USB >Pour se désinscrire : mailto:[EMAIL PROTECTED] > > > > > > > Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
