digimaster wrote:
> Oke new release is out, where it should be fixed.
>
> 'QLogitechMediaServer V1.07 QTS 4.2 or Higher and x86_64/x86/i686'
> (https://www.dropbox.com/s/vjvlqx8f2y08lxs/QLogitechMediaServer_V1.07_QTS-4.2_or_Higher_x86_64-x86.zip?dl=0)
>
> So please try this version ?
OK, I'm doing a clean install.
Stopping everything, removing QLMS app from appcenter, system reboot.
Manual install from appcenter...
same install behaviour.
-First quickly up to 45%, wait for a moment
-Then quickly up to 75%, wait for a moment
-Then up to 100%
Qnap log events...
Code:
--------------------
Information 2018/02/11 13:21:16 System 127.0.0.1
localhost [App Center] QLogitechMediaServer enabled.
Warning 2018/02/11 13:21:06 System 127.0.0.1
localhost [QLogitechMediaServer] Something went wrong, check the
/share/MD0_DATA/.qpkg/LogitechMediaServer/LogitechMediaServer.log.err and
you're configuration! You could Try /etc/init.d/LogitechMediaServer.sh
failsafe, or reinstall QPKG!
Warning 2018/02/11 13:20:19 System 127.0.0.1
localhost [QLogitechMediaServer] Upgrading LogitechMediaServer to
7.9.1-1517314665, please wait !
Warning 2018/02/11 13:19:58 System 127.0.0.1
localhost [QLogitechMediaServer] Please wait a few minuts, have to build
LMS from scratch !
Information 2018/02/11 13:19:57 System 127.0.0.1
localhost [App Center] QLogitechMediaServer 1.07 has been installed in
/share/MD0_DATA/.qpkg/LogitechMediaServer successfully.
Information 2018/02/11 13:16:38 System 127.0.0.1
localhost System started.
Information 2018/02/11 13:13:09 System 127.0.0.1
localhost System was shut down on Sun Feb 11 13:13:09 CET 2018.
Information 2018/02/11 13:11:32 admin 192.168.6.187 ---
[Power Management] System restarting.
--------------------
QLMS is not running...
Code:
--------------------
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # ./LogitechMediaServer.sh
status
LogitechMediaServer is not running, do ./LogitechMediaServer.sh start to
start services !
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # ps | grep [L]ogitechMediaServer
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # /bin/pidof slimserver.pl
[/share/MD0_DATA/.qpkg/LogitechMediaServer] #
--------------------
-->see attached logs (1st)
Trying to start manually [ ./LogitechMediaServer.sh start ], fails, no
process running (same as above)
Adjusting ownership [ chown -R squeezeboxserver:everyone SlimServer/ ]
and then starting [ ./LogitechMediaServer.sh start ], fails.
But slimserver.pl process is running! No web GUI however...
Code:
--------------------
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # chown -R
squeezeboxserver:everyone SlimServer/
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # ./LogitechMediaServer.sh start
Something went wrong, check the
/share/MD0_DATA/.qpkg/LogitechMediaServer/LogitechMediaServer.log.err and
you're configuration! You could Try ./LogitechMediaServer.sh failsafe, or
reinstall QPKG!
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # /bin/pidof slimserver.pl
24801
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # ps | grep [L]ogitechMediaServer
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # ps | grep squeezeboxserver
24801 squeezeboxserver 75080 S /usr/bin/perl
/share/MD0_DATA/.qpkg/LogitechM
26819 admin 536 R grep squeezeboxserver
[/share/MD0_DATA/.qpkg/LogitechMediaServer] #
--------------------
--> see attached logs (2nd)
Killing the the slimserver.pl manually.
Then adjusting access [ chmod -R 0755 SlimServer/ ] and owner [ chown -R
squeezeboxserver:everyone SlimServer/ ].
Then new start attempt [ ./LogitechMediaServer.sh start ], fails to
start, but slimserver process runs.
Web GUI works as well and I can start to set up LMS...
Code:
--------------------
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # ps | grep squeezeboxserver
32046 squeezeboxserver 82472 S /usr/bin/perl
/share/MD0_DATA/.qpkg/LogitechM
32205 admin 532 R grep squeezeboxserver
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # kill 32046
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # chmod -R 0755 SlimServer/
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # chown -R
squeezeboxserver:everyone SlimServer/
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # ./LogitechMediaServer.sh start
Something went wrong, check the
/share/MD0_DATA/.qpkg/LogitechMediaServer/LogitechMediaServer.log.err and
you're configuration! You could Try ./LogitechMediaServer.sh failsafe, or
reinstall QPKG!
[/share/MD0_DATA/.qpkg/LogitechMediaServer] # ps | grep squeezeboxserver
590 squeezeboxserver 80396 S /usr/bin/perl
/share/MD0_DATA/.qpkg/LogitechM
1567 admin 284 S grep squeezeboxserver
[/share/MD0_DATA/.qpkg/LogitechMediaServer] #
--------------------
--> see attached logs (3rd)
+-------------------------------------------------------------------+
|Filename: Log files.zip |
|Download: http://forums.slimdevices.com/attachment.php?attachmentid=24529|
+-------------------------------------------------------------------+
NAS: QNAP TS-459U+ -QTS 4.2.6- (4x 2TB, RAID5)
Services: LMS- 7.9.1 -, SSOTS- 4.14-
Squeezebox: 6x Reciever, 3x Boom, 2x SB3 Classic
Other: iPeng on iPad and iPhone
------------------------------------------------------------------------
jasell's Profile: http://forums.slimdevices.com/member.php?userid=17817
View this thread: http://forums.slimdevices.com/showthread.php?t=108292
_______________________________________________
Squeezecenter mailing list
[email protected]
http://lists.slimdevices.com/mailman/listinfo/squeezecenter
