Ok, I installed the motif packages. How am I supposed to know that? Sure, the
wiki install instructions on v5.1 say so - but I am not using v5.1. And there
is
no mention of "utsetup" in v5.1 install instructions. I am using "utsetup",
just
as recommended in v5.2 manual. The problem is, I don't know which of the v5.1
install instructions does apply, and which of them do not apply. I would like
the install instructions updated to v5.2. Is it a no-no to use "utsetup"? Is
there any short comings in "ipadm" and that command is inferior, instead I
should dabble with all the config files? etc? How do I know? Where is the
install instructions for v5.2? When (if) I get this working, I will post
install
instructions so newbies can benefit from them.
Now everything works, but it works bad. When I boot the Solaris PC, I can login
on the SunRay2 DTU. But it looks ugly. It is an old Motif login window. It says
"Sun Ray Mobile Session Login" and I have three choices: "Ok", "Start Over",
"Options"->"Quick Login/Exit", "Help". It also behaves strange. I enter my user
name, and then the "44B" error picture is shown briefly before I can type in my
password. And when I logout, I see the "44B" picture again briefly before
facing
the login Motif Window. Something is not really working.
And, the keyboard is not set. It is always "English" keyboard, no matter what I
choose on the keyboard icon on panel, top right. The default language is not
chosen.
So, something is not correct. Could it be that I use "ipadm" to get static IP?
Is it better to "sys-unconfig" to get static IP? Or, should I use the static IP
instructions for v5.1 on the wiki? Do they apply? The description on the wiki
is
very vague and high level. "modify this and that". I would like to know the
expected output so that I know I am on the right track. Something like
1. Fix this bla bla
Expected output: When you do "getent hosts <hostname>" you should see your
computer's IP adress.
2. Fix that bla bla
Expected output: When you do "ipadm show-addr" you should see...
etc
Then I know if I am doing it right and there will be less problems.
I see that Ivar wrote:
"It looks like the Sun Ray is getting its IP form 192.169.1.1 which is not the
Sun Ray server. You have a few option:
1. Configure DHCP on the Sun Ray server to provide the DHCP information to the
Sun Rays without giving out IP addresses. The DHCP informserver in utquery
should then point to 192.168.1.3 i think.
2. Add the correct DHCP information to your DHCP server on 192.168.1.1
3. You can name your Sun Ray server "sunray-servers" within your DNS domain.
If
you provide this domain name with your DHCP to the Sun ray it will search for
sunray-servers.domain.xxx and find it.
4. There is also a broadcast option to find the server if they are on the same
subnet I belief.
Ivar"
So what would be the easiest to do, and how do I do that? What syntax?
root@frasse:/opt/SUNWut/sbin# ./utgstatus
hostflags interface flags
192.168.1.0/24
--------- -------------------
frasse TN 192.168.1.3 UA-
root@frasse:/opt/SUNWut/sbin# ./utadm -l
LAN connections: On
Use IPv4 multicast
Sun Ray interconnect framework is not configured
root@frasse:/opt/SUNWut/sbin# ./utquery 192.168.1.2
terminalID=00144f946b02
terminalIPA=192.168.1.2
model=SunRayP8
currentAuth=192.168.1.3
currentFW=4.2_77_2009.10.19.17.01
currentBarrier=420
currentBarrierLevel=420
currentMTU=1500
Subnet=255.255.255.0
Router=192.168.1.1
LeaseTim=84740
DHCPServer=192.168.1.1
INFORMServer=192.168.1.1
FWservType=none
speed=100F
configMTU=1500
dnsList=192.168.1.1
stopqon=0
bandwidth=100000000
root@frasse:/opt/SUNWut/sbin# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232
index
1
inet 127.0.0.1 netmask ff000000
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.1.3 netmask ffffff00 broadcast 192.168.1.255
ether 0:1b:21:1e:2e:d0
lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252
index
1
inet6 ::1/128
e1000g0: flags=20002000840<RUNNING,MULTICAST,IPv6> mtu 1500 index 2
inet6 ::/0
ether 0:1b:21:1e:2e:d0
root@frasse:/opt/SUNWut/sbin# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
-------------------- -------------------- ----- ----- ---------- ---------
default 192.168.1.1 UG 5 13869
127.0.0.1 127.0.0.1 UH 2 248 lo0
192.168.1.0 192.168.1.3 U 4 669722 e1000g0
Routing Table: IPv6
Destination/Mask Gateway Flags Ref Use If
--------------------------- --------------------------- ----- --- ------- -----
::1 ::1 UH 15 9104 lo0
----- Original Message ----
From: Bob Doolittle <[email protected]>
To: SunRay-Users mailing list <[email protected]>
Cc: Kalle Anka <[email protected]>; Simon Annear <[email protected]>
Sent: Wed, May 25, 2011 11:46:47 PM
Subject: Re: [SunRay-Users] Fw: Install instructions of v5.2 for S11E? "44B"
Did you in fact install the Motif packages?
Things can appear as you say if you didn't install them, because on Solaris the
default policy is NSCM, which requires a Motif greeter, and it will cycle
trying
to start up and failing to do so if the required packages are not installed.
Those packages are (from the How-To):
SUNWmfrun SUNWtltk SUNWdtbas
-Bob
On 05/25/11 05:41 PM, Kalle Anka wrote:
> I dont get it. I did this:
>
> 1) Got static IP with "ipadm" with
> # svcadm disable svc:/network/physical:nwam
> # svcadm enable svc:/network/physical:default
> # ipadm create-add -T static -a 192.168.1.3/24 e1000g0/v4
> # route -p add default 192.168.1.1
>
> Modified "/etc/resolv.conf":
> domain bredbandsbolaget.com
> nameserver 195.54.122.200
> nameserver 195.54.122.204
>
> # cp /etc/nsswitch.dns /etc/nsswitch.conf
>
>
> 2) pkg install SUNWdhcs SUNWdhcsb SUNWdhcm
>
>
> 3) utsetup
>
> And I still get this output as shown below. utadm -l, seems to show IPv6 in
> currentAuth.
>
>
> The screen of the DTU flashes and power cycles. And the screen says "44B".
What
> the heck is wrong? This is getting tiresome. The install instructions are
quite
> high level. "get static ip" - yes but how? An example of each config file
would
> be enlightening.
>
>
>
>
>
>
>
>
> ----- Original Message ----
> From: Simon Annear<[email protected]>
> To: [email protected]; Kalle Anka<[email protected]>
> Sent: Wed, May 25, 2011 12:48:00 PM
> Subject: Re: [SunRay-Users] Fw: Install instructions of v5.2 for S11E?
>
> Hi Kalle
>
> I have just upgraded to Solaris 11 Express + SRS 5.2 and it's working for me
>:-)
>
> I used the steps on the sunray wiki, but it looks like you've got some
> networking problems (Your CurrentAuth value is an IP6 address and should show
> 192.168.1.3 based on what you have in your config)
>
> I setup my networking slightly differently (I installed S11 Express, ran
> /usr/sbin/sys-unconfig and rebooted). It then walked me through the "basic"
> network/host configuration. If you're not confident configuring IP on solaris
> this is a good way to do it. Sys-unconfig removes network config and shuts
the
> server down. Then when you power it up again it walks you through basic
>network
> setup tasks.
>
> Perhaps you could include the output of "/sbin/ifconfig e1000g0"
>
> Mine shows
> e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
> inet 192.168.0.29 netmask ffffff00 broadcast 192.168.0.255
>
>
> Here is the output of utquery on my sunray
>
>
> me@sunray29:/opt/SUNWut/sbin$ ./utquery 192.168.0.199
> terminalID=080020f94a6a
> terminalIPA=192.168.0.199
> model=CoronaP2
> currentAuth=192.168.0.29
> currentFW=4.3_50_2011.04.22.22.07
> currentBarrier=430
> currentBarrierLevel=430
> currentMTU=1472
> currentLease=5791
> Subnet=255.255.255.0
> Router=192.168.0.210
> MTU=1472
> LeaseTim=7200
> DHCPServer=192.168.0.210
> INFORMServer=192.168.0.29
> AuthSrvr=192.168.0.29
> AuthPort=7009
> LogHost=192.168.0.29
> FwSrvr=192.168.0.29
> NewTVer=4.3_50_2011.04.22.22.07
> FWservType=FWSrvr
> speed=100F
> parmsVersion=4.3_50_2011.04.22.22.07
> parmsBarrier=430
> configMTU=1472
> AltAuth=192.168.0.29
> dnsList=192.168.0.210
> dname=mydomain.org
> confEnabled=0
> stopqon=0
> bandwidth=100000000
> me@sunray29:/opt/SUNWut/sbin$
>
>
>
>
> On 05/25/11 09:48 AM, Kalle Anka wrote:
>> Ok, my earlier problem was that I had no static IP, because my install was
>> broken. I reinstalled and got static IP like this:
>>
>> --------------------------
>>
>> How to get static IP in Solaris 11 Express
>> # svcadm disable svc:/network/physical:nwam
>> # svcadm enable svc:/network/physical:default
>> # ipadm create-add -T static -a 192.168.1.3/24 e1000g0/v4
>> # route -p add default 192.168.1.1
>>
>> Add the last line in "/etc/resolv.conf":
>> nameserver 192.168.1.1
>> domain 195.54.122.200
>>
>> # cp /etc/nsswitch.dns /etc/nsswitch.conf
>>
>> And reboot.
>>
>> -------------------------
>>
>> Now I am trying to install SunRay v5.2 and does not succeed. This is what I
> did
>> to install:
>>
>> I installed these packages: SUNWdhcsb SUNWdhcs SUNWdhcm
>> and used /utsetup. Then I choose all default values - this means Lan
>> connections
>> is off. I turned on Lan connection with:
>> # utadm -L on
>>
>> I modified /etc/hosts, I added this line at the bottom:
>> 192.168.1.3 frasse
>>
>> and rebooted. Now it seems the SunRay2 DTU power cycles? Something like that.
>> Every second it power cycles. I can see the cursor arrow for a half a second,
>> then I see the cross cursor. And now I have this output below. What could be
>> the
>> problem? Should I reinstall? I am almost there...
>>
>>
>> root@frasse:/opt/SUNWut/sbin# ./utadm -l
>> LAN connections: On
>> Use IPv4 multicast
>> Sun Ray interconnect framework is not configured
>> root@frasse:/opt/SUNWut/sbin# ./utquery 192.168.1.2
>> terminalID=00144f946b02
>> terminalIPA=192.168.1.2
>> model=SunRayP8
>> currentAuth=b41a:508::56e3:d0fe:c0a8:102
>> currentFW=4.2_77_2009.10.19.17.01
>> currentBarrier=420
>> currentBarrierLevel=420
>> currentMTU=1500
>> Subnet=255.255.255.0
>> Router=192.168.1.1
>> LeaseTim=73302
>> DHCPServer=192.168.1.1
>> INFORMServer=192.168.1.1
>> FWservType=none
>> speed=100F
>> configMTU=1500
>> dnsList=192.168.1.1
>> stopqon=0
>> bandwidth=100000000
>>
>>
>> root@frasse:/opt/SUNWut/sbin# ./utgstatus
>> hostflags interface flags
>> 192.168.1.0/24
>> --------- -------------------
>> frasse TN 192.168.1.3 UA-
>>
>>
>> root@frasse:/opt/SUNWut/sbin# ./utadm -l
>> LAN connections: On
>> Use IPv4 multicast
>> Sun Ray interconnect framework is not configured
>>
>>
>> root@frasse:/opt/SUNWut/sbin# getent hosts frasse
>> 127.0.0.1 frasse frasse.local localhost loghost
>> 192.168.1.3 frasse frasse.local localhost loghost
>>
>>
>> root@frasse:/opt/SUNWut/sbin# cat /etc/hosts
>> # Internet host table
>> ::1 frasse frasse.local localhost loghost
>> 127.0.0.1 frasse frasse.local localhost loghost
>> 192.168.1.3 frasse
>> _______________________________________________
>> SunRay-Users mailing list
>> [email protected]
>> http://www.filibeto.org/mailman/listinfo/sunray-users
> _______________________________________________
> SunRay-Users mailing list
> [email protected]
> http://www.filibeto.org/mailman/listinfo/sunray-users
_______________________________________________
SunRay-Users mailing list
[email protected]
http://www.filibeto.org/mailman/listinfo/sunray-users
