Edgardo, Pretty sure it was 9600 8N1 no flow control.
Came right up in GPSCon.. Maybe its your cable, I used the cable that was shipped to me with the unit. I did have to manually initiate the auto survey, so comms are important.. Bye Said Sent From iPhone On Oct 14, 2012, at 21:36, Edgardo Molina <[email protected]> wrote: > Dear Said, > > I am having a very hard time trying to guess the communication port > configuration of the HP Z3805A. I am trying with different port settings to > match the PC and using different monitor and control programs. The afternoon > was not that fruitful regarding this. Is there a chance you have the default > port configuration for the Z3805A so I can match my PC serial port > configuration? > > I might be unavailable to respond to you tomorrow during the day, as I will > be at Queretaro with restricted access to the Internet. Despite this I will > be able to read my mail, not respond to it. Hope you don't mind. > > Your kind help is always welcome. Thanks. > > Regards, > > > > Edgardo Molina > Dirección IPTEL > > www.iptel.net.mx > > T : 55 55 55202444 > M : 04455 20501854 > > Piensa en Bits SA de CV > > > > Información anexa: > > > > > CONFIDENCIALIDAD DE INFORMACION > > Este mensaje tiene carácter confidencial. Si usted no es el destinarario de > este mensaje, le suplicamos se lo notifique al remitente mediante un correo > electrónico y que borre el presente mensaje y sus anexos de su computadora > sin retener una copia de los mismos. Queda estrictamente prohibido copiar > este mensaje o hacer usode el para cualquier propósito o divulgar su en forma > parcial o total su contenido. Gracias. > > > NON-DISCLOSURE OF INFORMATION > > This email is strictly confidential and may also be privileged. If you are > not the intended recipient please immediately advise the sender by replying > to this e-mail and then deleting the message and its attachments from your > computer without keeping a copy. It is strictly forbidden to copy it or use > it for any purpose or disclose its contents to any third party. Thank you. > > > > > > On Oct 14, 2012, at 11:05 PM, [email protected] wrote: > >> Hi Edgardo, >> >> I think the Z3805A and 58503A are identical, except in the rubber bumpers, >> maybe the power supply voltage setting, and the ID string.. >> >> I don't really care, the three units I have perform much better than >> anything else I have, so that satisfies my requirements.. >> >> In fact one of the units' ADEV can only be qualified by the BVA 8600 o >> scillator I have, and I don't know if I am measuring the BVA performance or >> the >> 58503A because I am measuring right at the specification of the BVA unit.. >> Wish I had two BVA's :) >> >> bye, >> Said >> >> >> In a message dated 10/14/2012 15:41:25 Pacific Daylight Time, >> [email protected] writes: >> >> Derived question: Will I get better GPSDO performance if I use a 58503A >> receiver? Or do you think our units match those 58503A GPSDOs out there? >> >> Again, thanks to everybody who helped me to figure out about my receivers >> and their inner workings. As always, you all made my day. >> >> >> Best regards, >> >> >> >> Edgardo Molina >> Dirección IPTEL >> >> _______________________________________________ >> time-nuts mailing list -- [email protected] >> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >> and follow the instructions there. > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
