you can also preset the receiver to the factory settings: :SYST:PRESET
for the SCPI command reference you can see the manual: www.leapsecond.com/museum/*hp58503a*/097-58503-13-iss-1.pdf On Mon, Oct 15, 2012 at 2:45 PM, Said Jackson <[email protected]> wrote: > Edgardo, > > Pretty sure it was 9600 8N1 no flow control. > > Came right up in GPSCon.. > > Maybe its your cable, I used the cable that was shipped to me with the > unit. > > I did have to manually initiate the auto survey, so comms are important.. > > Bye > Said > > Sent From iPhone > > On Oct 14, 2012, at 21:36, Edgardo Molina <[email protected]> wrote: > > > Dear Said, > > > > I am having a very hard time trying to guess the communication port > configuration of the HP Z3805A. I am trying with different port settings to > match the PC and using different monitor and control programs. The > afternoon was not that fruitful regarding this. Is there a chance you have > the default port configuration for the Z3805A so I can match my PC serial > port configuration? > > > > I might be unavailable to respond to you tomorrow during the day, as I > will be at Queretaro with restricted access to the Internet. Despite this I > will be able to read my mail, not respond to it. Hope you don't mind. > > > > Your kind help is always welcome. Thanks. > > > > Regards, > > > > > > > > Edgardo Molina > > Dirección IPTEL > > > > www.iptel.net.mx > > > > T : 55 55 55202444 > > M : 04455 20501854 > > > > Piensa en Bits SA de CV > > > > > > > > Información anexa: > > > > > > > > > > CONFIDENCIALIDAD DE INFORMACION > > > > Este mensaje tiene carácter confidencial. Si usted no es el destinarario > de este mensaje, le suplicamos se lo notifique al remitente mediante un > correo electrónico y que borre el presente mensaje y sus anexos de su > computadora sin retener una copia de los mismos. Queda estrictamente > prohibido copiar este mensaje o hacer usode el para cualquier propósito o > divulgar su en forma parcial o total su contenido. Gracias. > > > > > > NON-DISCLOSURE OF INFORMATION > > > > This email is strictly confidential and may also be privileged. If you > are not the intended recipient please immediately advise the sender by > replying to this e-mail and then deleting the message and its attachments > from your computer without keeping a copy. It is strictly forbidden to copy > it or use it for any purpose or disclose its contents to any third party. > Thank you. > > > > > > > > > > > > On Oct 14, 2012, at 11:05 PM, [email protected] wrote: > > > >> Hi Edgardo, > >> > >> I think the Z3805A and 58503A are identical, except in the rubber > bumpers, > >> maybe the power supply voltage setting, and the ID string.. > >> > >> I don't really care, the three units I have perform much better than > >> anything else I have, so that satisfies my requirements.. > >> > >> In fact one of the units' ADEV can only be qualified by the BVA 8600 o > >> scillator I have, and I don't know if I am measuring the BVA > performance or the > >> 58503A because I am measuring right at the specification of the BVA > unit.. > >> Wish I had two BVA's :) > >> > >> bye, > >> Said > >> > >> > >> In a message dated 10/14/2012 15:41:25 Pacific Daylight Time, > >> [email protected] writes: > >> > >> Derived question: Will I get better GPSDO performance if I use a 58503A > >> receiver? Or do you think our units match those 58503A GPSDOs out > there? > >> > >> Again, thanks to everybody who helped me to figure out about my > receivers > >> and their inner workings. As always, you all made my day. > >> > >> > >> Best regards, > >> > >> > >> > >> Edgardo Molina > >> Dirección IPTEL > >> > >> _______________________________________________ > >> time-nuts mailing list -- [email protected] > >> To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > >> and follow the instructions there. > > > > _______________________________________________ > > time-nuts mailing list -- [email protected] > > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > > and follow the instructions there. > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
