Hello Gentlemen,

 I also have a 42 aft cabin with the same gen set. Removing it in pieces is 
probably the best approach on that. As far as replacement, here's a whole 
different idea.


This may sound nuts but rather than installing another gen-set in the engine 
room (where incidentally it adds list to your port side) many cruisers and 
weekenders are using portable generators on deck. They're less expensive, can 
be stored in your garage when not in use, use the same fuel as your dinghy, 
adds room in your engine room to service your engines, can be plugged into you 
existing shore power plug and stowed practically anywhere on the outside of 
your boat, are very quiet while running (thus not disturbing your neighbors at 
anchor) and eliminate the port list that all our boats have.


Bernie?






-----Original Message-----
From: COPTERBC via UnifliteWorld <[email protected]>
To: unifliteworld <[email protected]>
Sent: Sun, Aug 3, 2014 6:05 pm
Subject: Re: [UnifliteWorld] Onan Gen.

       David,
 ?
 My gen. set is also on the port side fwd. of the port engine but my water  
heater is below the floor in the galley area. The gen. set is right up against  
the fwd bulkhead on the port side. The stairs down to the galley raise up  
for?access to the engine room. Access isn't as much a problem as the weight  of 
the old Onan. I think it will have to be taken out in pieces. I think?it  
weighs about 650 to 700 lb. The new one "only" weighs 360 lb plus the sound  
shield. I'm an old guy and can't do the heavy lifting that this will  require.
 ?
 Bob C.
 ?
 ?
  In a message dated 8/3/2014 5:29:27 P.M. US Mountain Standard Time,  
[email protected] writes:
       

   Bob, I have an '84 42 aft cabin, (42 SE II).? I don't know the    
configuration of you 42, but in mine the Genset is in the engine room on the    
port side near the forward bulkhead.? The water heater is outboard of the    
Onan.? Changing the water heater was a bear and while that was going on I    
figured that if I ever change out the genset, I would make the stairs, those    
going down to the galley from the salon, open.? Or at least remove the    
stairs during the genset swap.? My genset is right next to the under side    of 
the stairs.? Is yours similar?? Have you considered this    method?
   
DavidO    

                            From:      COPTERBC via UnifliteWorld      
<[email protected]>
To: [email protected]      
Sent: Sunday, August 3,      2014 12:27 PM
Subject:      [UnifliteWorld] Onan Gen.

     
               Has anyone had their gen. set replaced. I have a 7.5kW Onan MDJE 
that      is flat worn out and am going to have a Yanmar 7 kW installed. I have 
a 42      ft. aft cabin and it's going to be a real bear to get it replaced. 
Any      thoughts on this and approximately how long did it take?
     ?
     Thanks,
     ?
     Bob C.

-- 
You received this message because you      are subscribed to the Google Groups 
"UnifliteWorld" group.
To unsubscribe      from this group and stop receiving emails from it, send an 
email to [email protected].
To      post to this group, send email to [email protected].
Visit      this group at http://groups.google.com/group/unifliteworld.
For more      options, visit https://groups.google.com/d/optout.






   

   
-- 
You received this message because you are subscribed to the    Google Groups 
"UnifliteWorld" group.
To unsubscribe from this group and    stop receiving emails from it, send an 
email to [email protected].
To    post to this group, send email to [email protected].
Visit    this group at http://groups.google.com/group/unifliteworld.
For    more options, visit https://groups.google.com/d/optout.

  
  -- 
 You received this message because you are subscribed to the Google Groups 
"UnifliteWorld" group.
 To unsubscribe from this group and stop receiving emails from it, send an 
email to [email protected].
 To post to this group, send email to [email protected].
 Visit this group at http://groups.google.com/group/unifliteworld.
 For more options, visit https://groups.google.com/d/optout.
  
 

-- 
You received this message because you are subscribed to the Google Groups 
"UnifliteWorld" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To post to this group, send email to [email protected].
Visit this group at http://groups.google.com/group/unifliteworld.
For more options, visit https://groups.google.com/d/optout.

Reply via email to