Bob, I just pulled and replaced a 6.5 MCCK out of my 36 aft cabin about 4 months ago. It weighed about 425lbs.
I built a double A-frame inside the salon on my boat to remove and replace the gen with. Send me your phone # and I can tell you several things that I did to get my genset out and back in that worked really well for me. If you do not want to publish your phone # here send me a private email at [email protected] JerryL -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Sunday, August 03, 2014 8:05 PM To: [email protected] Subject: Re: [UnifliteWorld] Onan Gen. David, My gen. set is also on the port side fwd. of the port engine but my water heater is below the floor in the galley area. The gen. set is right up against the fwd bulkhead on the port side. The stairs down to the galley raise up for access to the engine room. Access isn't as much a problem as the weight of the old Onan. I think it will have to be taken out in pieces. I think it weighs about 650 to 700 lb. The new one "only" weighs 360 lb plus the sound shield. I'm an old guy and can't do the heavy lifting that this will require. Bob C. In a message dated 8/3/2014 5:29:27 P.M. US Mountain Standard Time, [email protected] writes: Bob, I have an '84 42 aft cabin, (42 SE II). I don't know the configuration of you 42, but in mine the Genset is in the engine room on the port side near the forward bulkhead. The water heater is outboard of the Onan. Changing the water heater was a bear and while that was going on I figured that if I ever change out the genset, I would make the stairs, those going down to the galley from the salon, open. Or at least remove the stairs during the genset swap. My genset is right next to the under side of the stairs. Is yours similar? Have you considered this method? DavidO -------------------------------------------------------------------------- From: COPTERBC via UnifliteWorld <[email protected]> To: [email protected] Sent: Sunday, August 3, 2014 12:27 PM Subject: [UnifliteWorld] Onan Gen. Has anyone had their gen. set replaced. I have a 7.5kW Onan MDJE that is flat worn out and am going to have a Yanmar 7 kW installed. I have a 42 ft. aft cabin and it's going to be a real bear to get it replaced. Any thoughts on this and approximately how long did it take? Thanks, Bob C. -- You received this message because you are subscribed to the Google Groups "UnifliteWorld" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at http://groups.google.com/group/unifliteworld. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "UnifliteWorld" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at http://groups.google.com/group/unifliteworld. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "UnifliteWorld" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at http://groups.google.com/group/unifliteworld. For more options, visit https://groups.google.com/d/optout. This e-mail and the files transmitted with it are legally privileged, confidential and intended solely for the use of the individual or entity to which they are addressed. If you have received this e-mail in error, please notify the sender and do not further disseminate, discuss, distribute or forward this message. Any views or opinions expressed in this e-mail are solely those of the author and do not necessarily represent those of the Company. The recipient should check this e-mail and any attachments for the presence of viruses. The Company accepts no liability for any damage caused by any virus transmitted by this e-mail. -- You received this message because you are subscribed to the Google Groups "UnifliteWorld" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at http://groups.google.com/group/unifliteworld. For more options, visit https://groups.google.com/d/optout.
