Hi Randal I had a similar problem. In my case it was due to the chip card of the phone operator that wasn't properly setup. I had to put it in a phone and reset it up with the right sms operator phone number.
Regards Nil -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Randal Law Sent: vendredi 10 janvier 2003 17:54 To: [EMAIL PROTECTED] Subject: Wavecom Modem Importance: High Hi All, I am using a Wavecom Fastrack WMOD2 Mobile modem. It seem kannel successfully initial the modem. But when It sending sms message its got error, please help! Thanks! bearerbox.log show below: 2003-01-10 15:58:51 [0] INFO: ---------------------------------------- 2003-01-10 15:58:51 [0] INFO: Kannel bearerbox II version cvs-20030109 starting 2003-01-10 15:58:51 [0] INFO: MAIN: Start-up done, entering mainloop 2003-01-10 15:58:51 [0] DEBUG: AT2[/dev/ttyS0]: start called 2003-01-10 15:58:51 [7] DEBUG: sms_router: list_len = 0 2003-01-10 15:58:51 [14] DEBUG: Started thread 16 (gw/bb_boxc.c:function) 2003-01-10 15:58:51 [16] INFO: Client connected from <127.0.0.1> 2003-01-10 15:58:51 [16] DEBUG: setting up systems for new wapbox 2003-01-10 15:58:51 [16] DEBUG: Started thread 17 (gw/bb_boxc.c:boxc_sender) 2003-01-10 15:58:52 [6] DEBUG: AT2[/dev/ttyS0]: device opened 2003-01-10 15:58:52 [6] INFO: AT2[/dev/ttyS0]: init device 2003-01-10 15:58:52 [6] INFO: AT2[/dev/ttyS0]: speed set to 9600 2003-01-10 15:58:52 [6] DEBUG: AT2[/dev/ttyS0]: --> AT^M 2003-01-10 15:58:52 [6] DEBUG: AT2[/dev/ttyS0]: <-- OK 2003-01-10 15:58:52 [6] DEBUG: AT2[/dev/ttyS0]: --> AT&F^M 2003-01-10 15:58:52 [6] DEBUG: AT2[/dev/ttyS0]: <-- OK 2003-01-10 15:58:52 [6] DEBUG: AT2[/dev/ttyS0]: --> ATE0^M 2003-01-10 15:58:52 [6] DEBUG: AT2[/dev/ttyS0]: <-- OK 2003-01-10 15:58:52 [6] DEBUG: AT2[/dev/ttyS0]: --> AT+IFC=2,2^M 2003-01-10 15:58:52 [6] DEBUG: AT2[/dev/ttyS0]: <-- OK 2003-01-10 15:58:52 [6] DEBUG: AT2[/dev/ttyS0]: --> AT+CPIN?^M 2003-01-10 15:58:52 [6] DEBUG: AT2[/dev/ttyS0]: <-- +CPIN: READY 2003-01-10 15:59:03 [6] DEBUG: AT2[/dev/ttyS0]: --> AT+CMGF=0^M 2003-01-10 15:59:03 [6] DEBUG: AT2[/dev/ttyS0]: <-- OK 2003-01-10 15:59:03 [6] DEBUG: AT2[/dev/ttyS0]: --> AT+CSMS=?^M 2003-01-10 15:59:03 [6] DEBUG: AT2[/dev/ttyS0]: <-- +CSMS: (0,1) 2003-01-10 15:59:03 [6] DEBUG: AT2[/dev/ttyS0]: <-- OK 2003-01-10 15:59:03 [6] INFO: AT2[/dev/ttyS0]: Phase 2+ is supported 2003-01-10 15:59:03 [6] DEBUG: AT2[/dev/ttyS0]: --> AT+CSMS=1^M 2003-01-10 15:59:03 [6] DEBUG: AT2[/dev/ttyS0]: <-- +CSMS: 1,1,1 2003-01-10 15:59:03 [6] DEBUG: AT2[/dev/ttyS0]: <-- OK 2003-01-10 15:59:03 [6] DEBUG: AT2[/dev/ttyS0]: --> AT+CNMI=1,2,0,1,0^M 2003-01-10 15:59:03 [6] DEBUG: AT2[/dev/ttyS0]: <-- OK 2003-01-10 15:59:03 [6] INFO: AT2[/dev/ttyS0]: AT SMSC successfully opened. 2003-01-10 15:59:10 [5] DEBUG: boxc_receiver: sms received 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: TP-Validity-Period: 24.0 hours 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: --> AT+CMGS=16^M 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: <-- > 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: send command status: 1 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: --> 0011000881592197680000A704E8321B0E 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: --> ^Z 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: <-- > 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: <-- ERROR 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: send command status: -1 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: --> AT+CMGS=16^M 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: <-- > 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: send command status: 1 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: --> 0011000881592197680000A704E8321B0E 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: --> ^Z 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: <-- > 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: <-- ERROR 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: send command status: -1 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: --> AT+CMGS=16^M 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: <-- > 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: send command status: 1 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: --> 0011000881592197680000A704E8321B0E 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: --> ^Z 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: <-- > 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: <-- ERROR 2003-01-10 15:59:11 [6] DEBUG: AT2[/dev/ttyS0]: send command status: -1 kannel.conf show below: group = core admin-port = 13000 smsbox-port = 13001 wapbox-port = 13002 admin-password = xxx wdp-interface-name = "*" log-file = "/var/log/kannel/bearerbox.log" access-log = "/var/log/kannel/bearer-access.log" group = smsc smsc = at2 modemtype = wavecom device = /dev/ttyS0 speed = 9600 group = smsbox bearerbox-host = sms.xxx.com sendsms-port = 13013 global-sender = 13013 log-file = "/var/log/kannel/smsbox.log" access-log = "/var/log/kannel/sms-access.log" group = sendsms-user username = xxx password = xxx # SERVICES group = sms-service keyword = nop text = "You asked nothing and I did it!" # there should be default always group = sms-service keyword = default text = "No service spesified" include = "/etc/kannel/modems.conf" include = "/etc/kannel/wapbox.conf" modems.conf show below: group = modems id = wavecom name = "wavecom" need-sleep = true Best Regards, Randal
