I have had the problem of the Decode button not coming on after the end of a receive interval. In my case I found the problem to be that the computer was being overloaded by high CPU usage of a web browser. This occurred with Edge, Chrome, or Firefox. This high CPU usage was seen by Task Manager. The solution was to close the web browser. What does Task Manager reveal in your case?
On Fri, Jul 5, 2019 at 8:59 AM Hasan al-Basri <hbasri.schie...@gmail.com> wrote: > Ok, I'll check it out. > > Downloading now, then will install right over the top of my existing 2.01 > Tnx > 73, N0AN > > Hasan > > > On Fri, Jul 5, 2019 at 7:46 AM Black Michael <mdblac...@yahoo.com> wrote: > >> This is version 2.0.1 with dropout debugging. >> If the decode light is not flashing then it sounds like you may have >> audio dropouts occurring. >> This version will show you when it fails with messages in the band >> activity window about "dropout". You'll see a few messages on startup >> which is normal as the audio catches up. >> >> >> https://www.dropbox.com/s/isxwjybws1i8u6f/wsjtx-2.0.1-win32-dropouts.exe?dl=1 >> >> de Mike W9MDB >> >> >> On Friday, July 5, 2019, 04:45:38 AM CDT, Hasan al-Basri < >> hbasri.schie...@gmail.com> wrote: >> >> >> Ok Mike, it decoded for > 24 hours but then stopped early this morning >> just before I got to the shack. >> >> Started 07/03/2019 @ 1723 >> Stopped 07/05/2019 @ 0407 Both local >> >> These are the file saved dates. Again, I had to reboot a few minutes ago >> to get it to start saving files/decoding again. >> >> The rig was unattended from about 6 p.m. last night until 4:19 a.m. when >> I came down to see if it was still decoding...I noticed it had stopped >> decoding 12 minutes b4 I got down here. >> >> Another symptom: When it stops decoding incoming signals, the Blue Decode >> light does NOT flash at the end of a sequence, ...even though the >> thermometer and the waterfall show sigs for the full sequence. >> >> Any other suggestions? >> 73, N0AN >> Hasan >> >> >> On Thu, Jul 4, 2019 at 5:35 AM Hasan al-Basri <hbasri.schie...@gmail.com> >> wrote: >> >> Ok, I'll check it out. Time is perfect and always is, I'm GPS locked to >> it. >> >> When I got down here this morning it was still decoding full fill of >> JTAlert. ...but it's only been 12 hours. (I did the remove driver, unplug >> it and let Win10 reinstall it at a reboot) . That's where I am now in my >> test.) >> >> Save none was checked, I just checked Save All, will provide if needed. >> >> Here's hoping... >> >> 73, N0AN >> Hasan >> >> >> On Wed, Jul 3, 2019 at 10:37 PM Black Michael <mdblac...@yahoo.com> >> wrote: >> >> We seem to be hearing problems with a few people on both 2.0.1 and >> 2.1.0-rc7. >> 2.0.1 has been out for a long time and if this was common I'd think we >> would have heard a lot more reports of the problem. >> Upgrading to 2.1.0-rc7 and back to 2.0.1 should (and I emphasize should) >> just revert completely back to 2.0.1 thought there is a bug with FT4 in >> that case. >> >> The common thread probably is Windows updates....or time is off. Check >> http://time.is to ensure you're time is reported as "Exact". >> >> If you see waterfall activity but no decodes on of three things is likely >> happening. >> >> #1 Time is off >> #2 WAV files are not being recorded. Ensure Save/All is checked and see >> if WAV files are showing up in the Save folder. One user found using >> Remote Desktop that audio files weren't being saved. TeamViewer worked >> though. >> #3 Audio corrupted. If WAV files are showing up but not decoding and >> your time is correct then send in a few audio files so we can look at them. >> >> de Mike W9MDB >> >> >> >> >> On Wednesday, July 3, 2019, 10:27:56 PM CDT, Tod Farrell WE5TR < >> we5t...@gmail.com> wrote: >> >> >> Similar issue here on 2.0.1, win10, and flex6700 after a long operating >> session or even a long monitoring session. I.e. I’ll leave the shack >> powered up monitoring a band while I’m at work or elsewhere in the house. >> >> When I come back sometimes the waterfall is showing activity, dT is good, >> time.is is good, but no decodes. >> Other times it’s that clicking transit or tune causes no generated audio >> to the DAX software which has a meter that shows me no incoming audio is >> present from WSJT-X. >> >> Typically corrected with a WSJT-X restart >> >> -- >> 73 >> >> Tod WE5TR >> While mobile >> >> On Jul 3, 2019, at 16:52, Hasan al-Basri <hbasri.schie...@gmail.com> >> wrote: >> >> Hi Mike, >> No transmitting at all. RF Chokes all over the place. No issues running >> KW out on any band 6m through 80m. (if I have just rebooted the computer). >> Once it has run for several hours. it will stop decoding, whether I have >> transmitted or not, no matter qrp or qro. I monitor 24x7 , go days without >> tx'ing...it still goes deaf. >> >> IOW, it's not a USB RFI problem. >> >> All power settings for USB have been set to never sleep. >> >> I"m baffled, like I said, it acts like a memory leak and I don't think >> it's a coincidence that it showed up the very first time after installing >> and running RC7 64 bit. >> >> The problem NEVER showed up b4 RC7 64 bit was installed. I didn't change >> a thing in my setup or operating habits. Now I have to reboot every day or >> it just stops decoding, even having uninstalled RC7 64 bit and returned to >> 2.01 Gen Release. >> >> Audio level is perfect, waterfall shows signals...no decode. >> Reboot...decodes resume. No other program shows any symptoms like this at >> all on the same computer. WSJT-X is running on its own USB Sound Dongle for >> both RX and TX....and has been for over a year. >> >> Any further ideas are most welcome (TS-590sg, running from headphone jack >> for rx audio) Audio sounds perfect to the ear. Levels are right... >> Most peculiar! >> >> 73, N0AN >> Hasan >> >> >> On Wed, Jul 3, 2019 at 4:39 PM Black Michael via wsjt-devel < >> wsjt-devel@lists.sourceforge.net> wrote: >> >> Failing audio or rig connections are most always due to RFI or USB ports >> going to sleep. >> If RFI low power transmissions can be tested and if they work but high >> power does not then it's RFI. >> The USB ports going to sleep can be solved. >> https://www.windowscentral.com/how-prevent-windows-10-turning-usb-devices >> >> de Mike W9MDB >> >> >> >> >> On Wednesday, July 3, 2019, 04:31:39 PM CDT, rjai...@gmail.com < >> rjai...@gmail.com> wrote: >> >> >> I’ve seen this with other radios. Definitely not a flex only issue. >> >> Ria >> N2RJ >> >> On Wed, Jul 3, 2019 at 4:58 PM DX Jami via wsjt-devel < >> wsjt-devel@lists.sourceforge.net> wrote: >> >> Peter, >> >> Flex has its own set of unique problems and fixes. Suggest you post your >> question on the Flex forum page. Good luck. >> >> Danny >> AH6FX/W4 >> >> On Wednesday, July 3, 2019, 3:11:48 PM EDT, Peter Putnam <pe...@ni6e.com> >> wrote: >> >> >> Greetings, >> >> I have been using WSJT-X quite successfully for several years during >> June VHF Contests. I experienced a failure of the WSJT program to accept >> received audio input after several hours of proper operation during the >> recent Field Day exercise. >> >> I'll provide a brief outline and reply with more detail, should it be >> needed. >> >> My computer is a Dell Optiplex 780 running Win 7 Pro SP1, 64-bit. The >> WSJT-X software version is 2.0.1 7ddcb7. >> >> My receiver is a Flex 6500. It passes data to a Flex-supplied "DAX" >> program that interfaces various applications that wish to receive the >> audio stream. WSJT accepts the stream and displays results on the Wide >> Graph and a small audio signal-strength window. Activity proceeded >> normally for the first three hours of Field Day, until both the Wide >> Graph and the audio signal-strength stopped showing any incoming audio. >> >> I can't offer any help on what might have caused the problem. It was >> abrupt and seemingly unrelated to any other system actions. I am unable >> to reproduce the problem. >> >> Several operators spent several hours speculating about what a solution >> might be. Program restarts and computer re-boots (time-tested favorite >> of generations) changed nothing. The only useful clue was that the DAX >> audio output stream was present and could be re-directed to Fldigi, but >> not to WSJT-X. >> >> I was able to restore operation for a brief period by stopping WSJT, >> renaming WSJT.ini and restarting WSJT. That fix lasted for a half hour. >> Repeating the procedure provided operation for the rest of Field Day. >> >> The two .ini files that were renamed are available for your inspection, >> along with the one that continued to function. >> >> Any suggestions you can offer to prevent a recurrence would be greatly >> appreciated. >> >> Regards, >> Peter >> NI6E >> >> >> >> >> >> >> _______________________________________________ >> wsjt-devel mailing list >> wsjt-devel@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >> _______________________________________________ >> wsjt-devel mailing list >> wsjt-devel@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >> >> _______________________________________________ >> wsjt-devel mailing list >> wsjt-devel@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >> _______________________________________________ >> wsjt-devel mailing list >> wsjt-devel@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >> >> _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel >
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
