Not an issue, I monitor CPU at all times, and keep in mind, once it stops decoding, even one time, it never resumes without a reboot. 73, N0AN Hasan
On Fri, Jul 5, 2019 at 10:14 AM Roy Gould <[email protected]> wrote: > I have had the problem of the Decode button not coming on after the end of > a receive interval. In my case I found the problem to be that the computer > was being overloaded by high CPU usage of a web browser. This occurred with > Edge, Chrome, or Firefox. This high CPU usage was seen by Task Manager. The > solution was to close the web browser. What does Task Manager reveal in > your case? > > On Fri, Jul 5, 2019 at 8:59 AM Hasan al-Basri <[email protected]> > wrote: > >> Ok, I'll check it out. >> >> Downloading now, then will install right over the top of my existing 2.01 >> Tnx >> 73, N0AN >> >> Hasan >> >> >> On Fri, Jul 5, 2019 at 7:46 AM Black Michael <[email protected]> wrote: >> >>> This is version 2.0.1 with dropout debugging. >>> If the decode light is not flashing then it sounds like you may have >>> audio dropouts occurring. >>> This version will show you when it fails with messages in the band >>> activity window about "dropout". You'll see a few messages on startup >>> which is normal as the audio catches up. >>> >>> >>> https://www.dropbox.com/s/isxwjybws1i8u6f/wsjtx-2.0.1-win32-dropouts.exe?dl=1 >>> >>> de Mike W9MDB >>> >>> >>> On Friday, July 5, 2019, 04:45:38 AM CDT, Hasan al-Basri < >>> [email protected]> wrote: >>> >>> >>> Ok Mike, it decoded for > 24 hours but then stopped early this morning >>> just before I got to the shack. >>> >>> Started 07/03/2019 @ 1723 >>> Stopped 07/05/2019 @ 0407 Both local >>> >>> These are the file saved dates. Again, I had to reboot a few minutes ago >>> to get it to start saving files/decoding again. >>> >>> The rig was unattended from about 6 p.m. last night until 4:19 a.m. >>> when I came down to see if it was still decoding...I noticed it had stopped >>> decoding 12 minutes b4 I got down here. >>> >>> Another symptom: When it stops decoding incoming signals, the Blue >>> Decode light does NOT flash at the end of a sequence, ...even though the >>> thermometer and the waterfall show sigs for the full sequence. >>> >>> Any other suggestions? >>> 73, N0AN >>> Hasan >>> >>> >>> On Thu, Jul 4, 2019 at 5:35 AM Hasan al-Basri <[email protected]> >>> wrote: >>> >>> Ok, I'll check it out. Time is perfect and always is, I'm GPS locked to >>> it. >>> >>> When I got down here this morning it was still decoding full fill of >>> JTAlert. ...but it's only been 12 hours. (I did the remove driver, unplug >>> it and let Win10 reinstall it at a reboot) . That's where I am now in my >>> test.) >>> >>> Save none was checked, I just checked Save All, will provide if needed. >>> >>> Here's hoping... >>> >>> 73, N0AN >>> Hasan >>> >>> >>> On Wed, Jul 3, 2019 at 10:37 PM Black Michael <[email protected]> >>> wrote: >>> >>> We seem to be hearing problems with a few people on both 2.0.1 and >>> 2.1.0-rc7. >>> 2.0.1 has been out for a long time and if this was common I'd think we >>> would have heard a lot more reports of the problem. >>> Upgrading to 2.1.0-rc7 and back to 2.0.1 should (and I emphasize should) >>> just revert completely back to 2.0.1 thought there is a bug with FT4 in >>> that case. >>> >>> The common thread probably is Windows updates....or time is off. Check >>> http://time.is to ensure you're time is reported as "Exact". >>> >>> If you see waterfall activity but no decodes on of three things is >>> likely happening. >>> >>> #1 Time is off >>> #2 WAV files are not being recorded. Ensure Save/All is checked and see >>> if WAV files are showing up in the Save folder. One user found using >>> Remote Desktop that audio files weren't being saved. TeamViewer worked >>> though. >>> #3 Audio corrupted. If WAV files are showing up but not decoding and >>> your time is correct then send in a few audio files so we can look at them. >>> >>> de Mike W9MDB >>> >>> >>> >>> >>> On Wednesday, July 3, 2019, 10:27:56 PM CDT, Tod Farrell WE5TR < >>> [email protected]> wrote: >>> >>> >>> Similar issue here on 2.0.1, win10, and flex6700 after a long operating >>> session or even a long monitoring session. I.e. I’ll leave the shack >>> powered up monitoring a band while I’m at work or elsewhere in the house. >>> >>> When I come back sometimes the waterfall is showing activity, dT is >>> good, time.is is good, but no decodes. >>> Other times it’s that clicking transit or tune causes no generated audio >>> to the DAX software which has a meter that shows me no incoming audio is >>> present from WSJT-X. >>> >>> Typically corrected with a WSJT-X restart >>> >>> -- >>> 73 >>> >>> Tod WE5TR >>> While mobile >>> >>> On Jul 3, 2019, at 16:52, Hasan al-Basri <[email protected]> >>> wrote: >>> >>> Hi Mike, >>> No transmitting at all. RF Chokes all over the place. No issues running >>> KW out on any band 6m through 80m. (if I have just rebooted the computer). >>> Once it has run for several hours. it will stop decoding, whether I have >>> transmitted or not, no matter qrp or qro. I monitor 24x7 , go days without >>> tx'ing...it still goes deaf. >>> >>> IOW, it's not a USB RFI problem. >>> >>> All power settings for USB have been set to never sleep. >>> >>> I"m baffled, like I said, it acts like a memory leak and I don't think >>> it's a coincidence that it showed up the very first time after installing >>> and running RC7 64 bit. >>> >>> The problem NEVER showed up b4 RC7 64 bit was installed. I didn't change >>> a thing in my setup or operating habits. Now I have to reboot every day or >>> it just stops decoding, even having uninstalled RC7 64 bit and returned to >>> 2.01 Gen Release. >>> >>> Audio level is perfect, waterfall shows signals...no decode. >>> Reboot...decodes resume. No other program shows any symptoms like this at >>> all on the same computer. WSJT-X is running on its own USB Sound Dongle for >>> both RX and TX....and has been for over a year. >>> >>> Any further ideas are most welcome (TS-590sg, running from headphone >>> jack for rx audio) Audio sounds perfect to the ear. Levels are right... >>> Most peculiar! >>> >>> 73, N0AN >>> Hasan >>> >>> >>> On Wed, Jul 3, 2019 at 4:39 PM Black Michael via wsjt-devel < >>> [email protected]> wrote: >>> >>> Failing audio or rig connections are most always due to RFI or USB ports >>> going to sleep. >>> If RFI low power transmissions can be tested and if they work but high >>> power does not then it's RFI. >>> The USB ports going to sleep can be solved. >>> https://www.windowscentral.com/how-prevent-windows-10-turning-usb-devices >>> >>> de Mike W9MDB >>> >>> >>> >>> >>> On Wednesday, July 3, 2019, 04:31:39 PM CDT, [email protected] < >>> [email protected]> wrote: >>> >>> >>> I’ve seen this with other radios. Definitely not a flex only issue. >>> >>> Ria >>> N2RJ >>> >>> On Wed, Jul 3, 2019 at 4:58 PM DX Jami via wsjt-devel < >>> [email protected]> wrote: >>> >>> Peter, >>> >>> Flex has its own set of unique problems and fixes. Suggest you post >>> your question on the Flex forum page. Good luck. >>> >>> Danny >>> AH6FX/W4 >>> >>> On Wednesday, July 3, 2019, 3:11:48 PM EDT, Peter Putnam <[email protected]> >>> wrote: >>> >>> >>> Greetings, >>> >>> I have been using WSJT-X quite successfully for several years during >>> June VHF Contests. I experienced a failure of the WSJT program to accept >>> received audio input after several hours of proper operation during the >>> recent Field Day exercise. >>> >>> I'll provide a brief outline and reply with more detail, should it be >>> needed. >>> >>> My computer is a Dell Optiplex 780 running Win 7 Pro SP1, 64-bit. The >>> WSJT-X software version is 2.0.1 7ddcb7. >>> >>> My receiver is a Flex 6500. It passes data to a Flex-supplied "DAX" >>> program that interfaces various applications that wish to receive the >>> audio stream. WSJT accepts the stream and displays results on the Wide >>> Graph and a small audio signal-strength window. Activity proceeded >>> normally for the first three hours of Field Day, until both the Wide >>> Graph and the audio signal-strength stopped showing any incoming audio. >>> >>> I can't offer any help on what might have caused the problem. It was >>> abrupt and seemingly unrelated to any other system actions. I am unable >>> to reproduce the problem. >>> >>> Several operators spent several hours speculating about what a solution >>> might be. Program restarts and computer re-boots (time-tested favorite >>> of generations) changed nothing. The only useful clue was that the DAX >>> audio output stream was present and could be re-directed to Fldigi, but >>> not to WSJT-X. >>> >>> I was able to restore operation for a brief period by stopping WSJT, >>> renaming WSJT.ini and restarting WSJT. That fix lasted for a half hour. >>> Repeating the procedure provided operation for the rest of Field Day. >>> >>> The two .ini files that were renamed are available for your inspection, >>> along with the one that continued to function. >>> >>> Any suggestions you can offer to prevent a recurrence would be greatly >>> appreciated. >>> >>> Regards, >>> Peter >>> NI6E >>> >>> >>> >>> >>> >>> >>> _______________________________________________ >>> wsjt-devel mailing list >>> [email protected] >>> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >>> _______________________________________________ >>> wsjt-devel mailing list >>> [email protected] >>> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >>> >>> _______________________________________________ >>> wsjt-devel mailing list >>> [email protected] >>> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >>> _______________________________________________ >>> wsjt-devel mailing list >>> [email protected] >>> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >>> >>> _______________________________________________ >> wsjt-devel mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >> > _______________________________________________ > wsjt-devel mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/wsjt-devel >
_______________________________________________ wsjt-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/wsjt-devel
