Ok, I'll check it out. Downloading now, then will install right over the top of my existing 2.01 Tnx 73, N0AN
Hasan On Fri, Jul 5, 2019 at 7:46 AM Black Michael <mdblac...@yahoo.com> wrote: > This is version 2.0.1 with dropout debugging. > If the decode light is not flashing then it sounds like you may have audio > dropouts occurring. > This version will show you when it fails with messages in the band > activity window about "dropout". You'll see a few messages on startup > which is normal as the audio catches up. > > > https://www.dropbox.com/s/isxwjybws1i8u6f/wsjtx-2.0.1-win32-dropouts.exe?dl=1 > > de Mike W9MDB > > > On Friday, July 5, 2019, 04:45:38 AM CDT, Hasan al-Basri < > hbasri.schie...@gmail.com> wrote: > > > Ok Mike, it decoded for > 24 hours but then stopped early this morning > just before I got to the shack. > > Started 07/03/2019 @ 1723 > Stopped 07/05/2019 @ 0407 Both local > > These are the file saved dates. Again, I had to reboot a few minutes ago > to get it to start saving files/decoding again. > > The rig was unattended from about 6 p.m. last night until 4:19 a.m. when > I came down to see if it was still decoding...I noticed it had stopped > decoding 12 minutes b4 I got down here. > > Another symptom: When it stops decoding incoming signals, the Blue Decode > light does NOT flash at the end of a sequence, ...even though the > thermometer and the waterfall show sigs for the full sequence. > > Any other suggestions? > 73, N0AN > Hasan > > > On Thu, Jul 4, 2019 at 5:35 AM Hasan al-Basri <hbasri.schie...@gmail.com> > wrote: > > Ok, I'll check it out. Time is perfect and always is, I'm GPS locked to it. > > When I got down here this morning it was still decoding full fill of > JTAlert. ...but it's only been 12 hours. (I did the remove driver, unplug > it and let Win10 reinstall it at a reboot) . That's where I am now in my > test.) > > Save none was checked, I just checked Save All, will provide if needed. > > Here's hoping... > > 73, N0AN > Hasan > > > On Wed, Jul 3, 2019 at 10:37 PM Black Michael <mdblac...@yahoo.com> wrote: > > We seem to be hearing problems with a few people on both 2.0.1 and > 2.1.0-rc7. > 2.0.1 has been out for a long time and if this was common I'd think we > would have heard a lot more reports of the problem. > Upgrading to 2.1.0-rc7 and back to 2.0.1 should (and I emphasize should) > just revert completely back to 2.0.1 thought there is a bug with FT4 in > that case. > > The common thread probably is Windows updates....or time is off. Check > http://time.is to ensure you're time is reported as "Exact". > > If you see waterfall activity but no decodes on of three things is likely > happening. > > #1 Time is off > #2 WAV files are not being recorded. Ensure Save/All is checked and see > if WAV files are showing up in the Save folder. One user found using > Remote Desktop that audio files weren't being saved. TeamViewer worked > though. > #3 Audio corrupted. If WAV files are showing up but not decoding and your > time is correct then send in a few audio files so we can look at them. > > de Mike W9MDB > > > > > On Wednesday, July 3, 2019, 10:27:56 PM CDT, Tod Farrell WE5TR < > we5t...@gmail.com> wrote: > > > Similar issue here on 2.0.1, win10, and flex6700 after a long operating > session or even a long monitoring session. I.e. I’ll leave the shack > powered up monitoring a band while I’m at work or elsewhere in the house. > > When I come back sometimes the waterfall is showing activity, dT is good, > time.is is good, but no decodes. > Other times it’s that clicking transit or tune causes no generated audio > to the DAX software which has a meter that shows me no incoming audio is > present from WSJT-X. > > Typically corrected with a WSJT-X restart > > -- > 73 > > Tod WE5TR > While mobile > > On Jul 3, 2019, at 16:52, Hasan al-Basri <hbasri.schie...@gmail.com> > wrote: > > Hi Mike, > No transmitting at all. RF Chokes all over the place. No issues running KW > out on any band 6m through 80m. (if I have just rebooted the computer). > Once it has run for several hours. it will stop decoding, whether I have > transmitted or not, no matter qrp or qro. I monitor 24x7 , go days without > tx'ing...it still goes deaf. > > IOW, it's not a USB RFI problem. > > All power settings for USB have been set to never sleep. > > I"m baffled, like I said, it acts like a memory leak and I don't think > it's a coincidence that it showed up the very first time after installing > and running RC7 64 bit. > > The problem NEVER showed up b4 RC7 64 bit was installed. I didn't change a > thing in my setup or operating habits. Now I have to reboot every day or it > just stops decoding, even having uninstalled RC7 64 bit and returned to > 2.01 Gen Release. > > Audio level is perfect, waterfall shows signals...no decode. > Reboot...decodes resume. No other program shows any symptoms like this at > all on the same computer. WSJT-X is running on its own USB Sound Dongle for > both RX and TX....and has been for over a year. > > Any further ideas are most welcome (TS-590sg, running from headphone jack > for rx audio) Audio sounds perfect to the ear. Levels are right... > Most peculiar! > > 73, N0AN > Hasan > > > On Wed, Jul 3, 2019 at 4:39 PM Black Michael via wsjt-devel < > wsjt-devel@lists.sourceforge.net> wrote: > > Failing audio or rig connections are most always due to RFI or USB ports > going to sleep. > If RFI low power transmissions can be tested and if they work but high > power does not then it's RFI. > The USB ports going to sleep can be solved. > https://www.windowscentral.com/how-prevent-windows-10-turning-usb-devices > > de Mike W9MDB > > > > > On Wednesday, July 3, 2019, 04:31:39 PM CDT, rjai...@gmail.com < > rjai...@gmail.com> wrote: > > > I’ve seen this with other radios. Definitely not a flex only issue. > > Ria > N2RJ > > On Wed, Jul 3, 2019 at 4:58 PM DX Jami via wsjt-devel < > wsjt-devel@lists.sourceforge.net> wrote: > > Peter, > > Flex has its own set of unique problems and fixes. Suggest you post your > question on the Flex forum page. Good luck. > > Danny > AH6FX/W4 > > On Wednesday, July 3, 2019, 3:11:48 PM EDT, Peter Putnam <pe...@ni6e.com> > wrote: > > > Greetings, > > I have been using WSJT-X quite successfully for several years during > June VHF Contests. I experienced a failure of the WSJT program to accept > received audio input after several hours of proper operation during the > recent Field Day exercise. > > I'll provide a brief outline and reply with more detail, should it be > needed. > > My computer is a Dell Optiplex 780 running Win 7 Pro SP1, 64-bit. The > WSJT-X software version is 2.0.1 7ddcb7. > > My receiver is a Flex 6500. It passes data to a Flex-supplied "DAX" > program that interfaces various applications that wish to receive the > audio stream. WSJT accepts the stream and displays results on the Wide > Graph and a small audio signal-strength window. Activity proceeded > normally for the first three hours of Field Day, until both the Wide > Graph and the audio signal-strength stopped showing any incoming audio. > > I can't offer any help on what might have caused the problem. It was > abrupt and seemingly unrelated to any other system actions. I am unable > to reproduce the problem. > > Several operators spent several hours speculating about what a solution > might be. Program restarts and computer re-boots (time-tested favorite > of generations) changed nothing. The only useful clue was that the DAX > audio output stream was present and could be re-directed to Fldigi, but > not to WSJT-X. > > I was able to restore operation for a brief period by stopping WSJT, > renaming WSJT.ini and restarting WSJT. That fix lasted for a half hour. > Repeating the procedure provided operation for the rest of Field Day. > > The two .ini files that were renamed are available for your inspection, > along with the one that continued to function. > > Any suggestions you can offer to prevent a recurrence would be greatly > appreciated. > > Regards, > Peter > NI6E > > > > > > > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel > > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel > >
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
