If you're not seeing dropout messages with the dropout debug version than your
audio stream has completely stopped.The dropouts are only checked when the
audio packets are flowing.You should be seeing a few messages at startup about
dataSink1 like this to ensure you're running the dropout version.
I would suggest uinstalling audio drivers, reboot, and reinstall.
de Mike W9MDB
On Friday, July 5, 2019, 08:49:10 PM CDT, Tod Farrell WE5TR
<we5t...@gmail.com> wrote:
Note: I screwed up and have no audio save to go with the notes. In the debug
version were there other logs I can grab for you?
Started this process around 14:00 UTC (all times in filenames and photos
attached are UTC)
moved all audio files to give clean directory
rebooted
downloadeed debug app
set shortcuts for different rig names
ran time sync
made qso as test (10m)
14:15 UTC walking away
When I came by the PC on occasions i saw no decode (blue) or decode results had
occured. When i stopped the test I grabbed the screenshot "190705 2355 gap..."
which shows a gap from 163345 to 180515. During a few of these gaps i stood and
watched task manager and the other WSJT-X instance looking for any issues. I
couldnt identify anything. Note: During the gaps when I was observing i did see
audio still in DAX which is what feeds the WSJT-X.
Today with this version, the decodes started again with no user intervention.
The Flex SDR waterfall showed activity in the band.
However, while I have the ALL files and the screenshots. I just now while
typing this up see that I have no audio save files. (that is an oh crap moment)
screenshots attached. Filenames have date_time and situational description
73,Tod
WE5TR
On Fri, Jul 5, 2019 at 2:58 PM Hasan al-Basri <hbasri.schie...@gmail.com> wrote:
INstalled and running Mike. Will watch for it...when it fails, it stays failed,
so all I have to do is watch the Save directory last decode having started just
now. Probably wont show until tomorrow. It'w working fine now, but it does for
hours before the first freak out.73, N0ANHasan
On Fri, Jul 5, 2019 at 9:53 AM Hasan al-Basri <hbasri.schie...@gmail.com> wrote:
Ok, I'll check it out.
Downloading now, then will install right over the top of my existing 2.01Tnx73,
N0AN
Hasan
On Fri, Jul 5, 2019 at 7:46 AM Black Michael <mdblac...@yahoo.com> wrote:
This is version 2.0.1 with dropout debugging.If the decode light is not
flashing then it sounds like you may have audio dropouts occurring.This version
will show you when it fails with messages in the band activity window about
"dropout". You'll see a few messages on startup which is normal as the audio
catches up.
https://www.dropbox.com/s/isxwjybws1i8u6f/wsjtx-2.0.1-win32-dropouts.exe?dl=1
de Mike W9MDB
On Friday, July 5, 2019, 04:45:38 AM CDT, Hasan al-Basri
<hbasri.schie...@gmail.com> wrote:
Ok Mike, it decoded for > 24 hours but then stopped early this morning just
before I got to the shack.
Started 07/03/2019 @ 1723Stopped 07/05/2019 @ 0407 Both local
These are the file saved dates. Again, I had to reboot a few minutes ago to get
it to start saving files/decoding again.
The rig was unattended from about 6 p.m. last night until 4:19 a.m. when I
came down to see if it was still decoding...I noticed it had stopped decoding
12 minutes b4 I got down here.
Another symptom: When it stops decoding incoming signals, the Blue Decode light
does NOT flash at the end of a sequence, ...even though the thermometer and the
waterfall show sigs for the full sequence.
Any other suggestions?73, N0ANHasan
On Thu, Jul 4, 2019 at 5:35 AM Hasan al-Basri <hbasri.schie...@gmail.com> wrote:
Ok, I'll check it out. Time is perfect and always is, I'm GPS locked to it.
When I got down here this morning it was still decoding full fill of JTAlert.
...but it's only been 12 hours. (I did the remove driver, unplug it and let
Win10 reinstall it at a reboot) . That's where I am now in my test.)
Save none was checked, I just checked Save All, will provide if needed.
Here's hoping...
73, N0ANHasan
On Wed, Jul 3, 2019 at 10:37 PM Black Michael <mdblac...@yahoo.com> wrote:
We seem to be hearing problems with a few people on both 2.0.1 and 2.1.0-rc7.
2.0.1 has been out for a long time and if this was common I'd think we would
have heard a lot more reports of the problem.Upgrading to 2.1.0-rc7 and back to
2.0.1 should (and I emphasize should) just revert completely back to 2.0.1
thought there is a bug with FT4 in that case.
The common thread probably is Windows updates....or time is off. Check
http://time.is to ensure you're time is reported as "Exact".
If you see waterfall activity but no decodes on of three things is likely
happening.
#1 Time is off#2 WAV files are not being recorded. Ensure Save/All is checked
and see if WAV files are showing up in the Save folder. One user found using
Remote Desktop that audio files weren't being saved. TeamViewer worked
though.#3 Audio corrupted. If WAV files are showing up but not decoding and
your time is correct then send in a few audio files so we can look at them.
de Mike W9MDB
On Wednesday, July 3, 2019, 10:27:56 PM CDT, Tod Farrell WE5TR
<we5t...@gmail.com> wrote:
Similar issue here on 2.0.1, win10, and flex6700 after a long operating
session or even a long monitoring session. I.e. I’ll leave the shack powered up
monitoring a band while I’m at work or elsewhere in the house.
When I come back sometimes the waterfall is showing activity, dT is good,
time.is is good, but no decodes.Other times it’s that clicking transit or tune
causes no generated audio to the DAX software which has a meter that shows me
no incoming audio is present from WSJT-X.
Typically corrected with a WSJT-X restart
--73
Tod WE5TRWhile mobile
On Jul 3, 2019, at 16:52, Hasan al-Basri <hbasri.schie...@gmail.com> wrote:
Hi Mike,No transmitting at all. RF Chokes all over the place. No issues running
KW out on any band 6m through 80m. (if I have just rebooted the computer). Once
it has run for several hours. it will stop decoding, whether I have transmitted
or not, no matter qrp or qro. I monitor 24x7 , go days without tx'ing...it
still goes deaf.
IOW, it's not a USB RFI problem.
All power settings for USB have been set to never sleep.
I"m baffled, like I said, it acts like a memory leak and I don't think it's a
coincidence that it showed up the very first time after installing and running
RC7 64 bit.
The problem NEVER showed up b4 RC7 64 bit was installed. I didn't change a
thing in my setup or operating habits. Now I have to reboot every day or it
just stops decoding, even having uninstalled RC7 64 bit and returned to 2.01
Gen Release.
Audio level is perfect, waterfall shows signals...no decode. Reboot...decodes
resume. No other program shows any symptoms like this at all on the same
computer. WSJT-X is running on its own USB Sound Dongle for both RX and
TX....and has been for over a year. Any further ideas are most welcome
(TS-590sg, running from headphone jack for rx audio) Audio sounds perfect to
the ear. Levels are right...Most peculiar!
73, N0ANHasan
On Wed, Jul 3, 2019 at 4:39 PM Black Michael via wsjt-devel
<wsjt-devel@lists.sourceforge.net> wrote:
Failing audio or rig connections are most always due to RFI or USB ports going
to sleep.If RFI low power transmissions can be tested and if they work but high
power does not then it's RFI.The USB ports going to sleep can be
solved.https://www.windowscentral.com/how-prevent-windows-10-turning-usb-devices
de Mike W9MDB
On Wednesday, July 3, 2019, 04:31:39 PM CDT, rjai...@gmail.com
<rjai...@gmail.com> wrote:
I’ve seen this with other radios. Definitely not a flex only issue.
RiaN2RJ
On Wed, Jul 3, 2019 at 4:58 PM DX Jami via wsjt-devel
<wsjt-devel@lists.sourceforge.net> wrote:
Peter,
Flex has its own set of unique problems and fixes. Suggest you post your
question on the Flex forum page. Good luck.
Danny AH6FX/W4
On Wednesday, July 3, 2019, 3:11:48 PM EDT, Peter Putnam <pe...@ni6e.com>
wrote:
Greetings,
I have been using WSJT-X quite successfully for several years during
June VHF Contests. I experienced a failure of the WSJT program to accept
received audio input after several hours of proper operation during the
recent Field Day exercise.
I'll provide a brief outline and reply with more detail, should it be
needed.
My computer is a Dell Optiplex 780 running Win 7 Pro SP1, 64-bit. The
WSJT-X software version is 2.0.1 7ddcb7.
My receiver is a Flex 6500. It passes data to a Flex-supplied "DAX"
program that interfaces various applications that wish to receive the
audio stream. WSJT accepts the stream and displays results on the Wide
Graph and a small audio signal-strength window. Activity proceeded
normally for the first three hours of Field Day, until both the Wide
Graph and the audio signal-strength stopped showing any incoming audio.
I can't offer any help on what might have caused the problem. It was
abrupt and seemingly unrelated to any other system actions. I am unable
to reproduce the problem.
Several operators spent several hours speculating about what a solution
might be. Program restarts and computer re-boots (time-tested favorite
of generations) changed nothing. The only useful clue was that the DAX
audio output stream was present and could be re-directed to Fldigi, but
not to WSJT-X.
I was able to restore operation for a brief period by stopping WSJT,
renaming WSJT.ini and restarting WSJT. That fix lasted for a half hour.
Repeating the procedure provided operation for the rest of Field Day.
The two .ini files that were renamed are available for your inspection,
along with the one that continued to function.
Any suggestions you can offer to prevent a recurrence would be greatly
appreciated.
Regards,
Peter
NI6E
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
