Ok Mike, it decoded for > 24 hours but then stopped early this morning just before I got to the shack.
Started 07/03/2019 @ 1723 Stopped 07/05/2019 @ 0407 Both local These are the file saved dates. Again, I had to reboot a few minutes ago to get it to start saving files/decoding again. The rig was unattended from about 6 p.m. last night until 4:19 a.m. when I came down to see if it was still decoding...I noticed it had stopped decoding 12 minutes b4 I got down here. Another symptom: When it stops decoding incoming signals, the Blue Decode light does NOT flash at the end of a sequence, ...even though the thermometer and the waterfall show sigs for the full sequence. Any other suggestions? 73, N0AN Hasan On Thu, Jul 4, 2019 at 5:35 AM Hasan al-Basri <[email protected]> wrote: > Ok, I'll check it out. Time is perfect and always is, I'm GPS locked to it. > > When I got down here this morning it was still decoding full fill of > JTAlert. ...but it's only been 12 hours. (I did the remove driver, unplug > it and let Win10 reinstall it at a reboot) . That's where I am now in my > test.) > > Save none was checked, I just checked Save All, will provide if needed. > > Here's hoping... > > 73, N0AN > Hasan > > > On Wed, Jul 3, 2019 at 10:37 PM Black Michael <[email protected]> wrote: > >> We seem to be hearing problems with a few people on both 2.0.1 and >> 2.1.0-rc7. >> 2.0.1 has been out for a long time and if this was common I'd think we >> would have heard a lot more reports of the problem. >> Upgrading to 2.1.0-rc7 and back to 2.0.1 should (and I emphasize should) >> just revert completely back to 2.0.1 thought there is a bug with FT4 in >> that case. >> >> The common thread probably is Windows updates....or time is off. Check >> http://time.is to ensure you're time is reported as "Exact". >> >> If you see waterfall activity but no decodes on of three things is likely >> happening. >> >> #1 Time is off >> #2 WAV files are not being recorded. Ensure Save/All is checked and see >> if WAV files are showing up in the Save folder. One user found using >> Remote Desktop that audio files weren't being saved. TeamViewer worked >> though. >> #3 Audio corrupted. If WAV files are showing up but not decoding and >> your time is correct then send in a few audio files so we can look at them. >> >> de Mike W9MDB >> >> >> >> >> On Wednesday, July 3, 2019, 10:27:56 PM CDT, Tod Farrell WE5TR < >> [email protected]> wrote: >> >> >> Similar issue here on 2.0.1, win10, and flex6700 after a long operating >> session or even a long monitoring session. I.e. I’ll leave the shack >> powered up monitoring a band while I’m at work or elsewhere in the house. >> >> When I come back sometimes the waterfall is showing activity, dT is good, >> time.is is good, but no decodes. >> Other times it’s that clicking transit or tune causes no generated audio >> to the DAX software which has a meter that shows me no incoming audio is >> present from WSJT-X. >> >> Typically corrected with a WSJT-X restart >> >> -- >> 73 >> >> Tod WE5TR >> While mobile >> >> On Jul 3, 2019, at 16:52, Hasan al-Basri <[email protected]> >> wrote: >> >> Hi Mike, >> No transmitting at all. RF Chokes all over the place. No issues running >> KW out on any band 6m through 80m. (if I have just rebooted the computer). >> Once it has run for several hours. it will stop decoding, whether I have >> transmitted or not, no matter qrp or qro. I monitor 24x7 , go days without >> tx'ing...it still goes deaf. >> >> IOW, it's not a USB RFI problem. >> >> All power settings for USB have been set to never sleep. >> >> I"m baffled, like I said, it acts like a memory leak and I don't think >> it's a coincidence that it showed up the very first time after installing >> and running RC7 64 bit. >> >> The problem NEVER showed up b4 RC7 64 bit was installed. I didn't change >> a thing in my setup or operating habits. Now I have to reboot every day or >> it just stops decoding, even having uninstalled RC7 64 bit and returned to >> 2.01 Gen Release. >> >> Audio level is perfect, waterfall shows signals...no decode. >> Reboot...decodes resume. No other program shows any symptoms like this at >> all on the same computer. WSJT-X is running on its own USB Sound Dongle for >> both RX and TX....and has been for over a year. >> >> Any further ideas are most welcome (TS-590sg, running from headphone jack >> for rx audio) Audio sounds perfect to the ear. Levels are right... >> Most peculiar! >> >> 73, N0AN >> Hasan >> >> >> On Wed, Jul 3, 2019 at 4:39 PM Black Michael via wsjt-devel < >> [email protected]> wrote: >> >> Failing audio or rig connections are most always due to RFI or USB ports >> going to sleep. >> If RFI low power transmissions can be tested and if they work but high >> power does not then it's RFI. >> The USB ports going to sleep can be solved. >> https://www.windowscentral.com/how-prevent-windows-10-turning-usb-devices >> >> de Mike W9MDB >> >> >> >> >> On Wednesday, July 3, 2019, 04:31:39 PM CDT, [email protected] < >> [email protected]> wrote: >> >> >> I’ve seen this with other radios. Definitely not a flex only issue. >> >> Ria >> N2RJ >> >> On Wed, Jul 3, 2019 at 4:58 PM DX Jami via wsjt-devel < >> [email protected]> wrote: >> >> Peter, >> >> Flex has its own set of unique problems and fixes. Suggest you post your >> question on the Flex forum page. Good luck. >> >> Danny >> AH6FX/W4 >> >> On Wednesday, July 3, 2019, 3:11:48 PM EDT, Peter Putnam <[email protected]> >> wrote: >> >> >> Greetings, >> >> I have been using WSJT-X quite successfully for several years during >> June VHF Contests. I experienced a failure of the WSJT program to accept >> received audio input after several hours of proper operation during the >> recent Field Day exercise. >> >> I'll provide a brief outline and reply with more detail, should it be >> needed. >> >> My computer is a Dell Optiplex 780 running Win 7 Pro SP1, 64-bit. The >> WSJT-X software version is 2.0.1 7ddcb7. >> >> My receiver is a Flex 6500. It passes data to a Flex-supplied "DAX" >> program that interfaces various applications that wish to receive the >> audio stream. WSJT accepts the stream and displays results on the Wide >> Graph and a small audio signal-strength window. Activity proceeded >> normally for the first three hours of Field Day, until both the Wide >> Graph and the audio signal-strength stopped showing any incoming audio. >> >> I can't offer any help on what might have caused the problem. It was >> abrupt and seemingly unrelated to any other system actions. I am unable >> to reproduce the problem. >> >> Several operators spent several hours speculating about what a solution >> might be. Program restarts and computer re-boots (time-tested favorite >> of generations) changed nothing. The only useful clue was that the DAX >> audio output stream was present and could be re-directed to Fldigi, but >> not to WSJT-X. >> >> I was able to restore operation for a brief period by stopping WSJT, >> renaming WSJT.ini and restarting WSJT. That fix lasted for a half hour. >> Repeating the procedure provided operation for the rest of Field Day. >> >> The two .ini files that were renamed are available for your inspection, >> along with the one that continued to function. >> >> Any suggestions you can offer to prevent a recurrence would be greatly >> appreciated. >> >> Regards, >> Peter >> NI6E >> >> >> >> >> >> >> _______________________________________________ >> wsjt-devel mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >> _______________________________________________ >> wsjt-devel mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >> >> _______________________________________________ >> wsjt-devel mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >> _______________________________________________ >> wsjt-devel mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >> >>
_______________________________________________ wsjt-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/wsjt-devel
