I've identified some problems with the 101D that I'll be fixing.
Mike W9MDB

 

    On Sunday, May 24, 2020, 12:55:37 AM CDT, Ken Chandler via wsjt-devel 
<wsjt-devel@lists.sourceforge.net> wrote:  
 
 I had issues to but on window 10 platform.I used the FT5000 rig, everything 
burst into life when I switched over from FTdx101D 

Ken.. G0ORH
Sent from my iPad

On 24 May 2020, at 01:02, John Zantek <j...@zantek.net> wrote:




Bill,

Many new 101MP owners in the PNW have been experiencing some setup issues, 
resulting in lots of phone calls.  

Have you been able to talk to the rig with any other S/W via USB and with what 
virtual settings?

Is the PC using USB 2.0 or 3.x ?  The 101MP is unfortunately persnickety in 
that regard.

No hubs, right?

73 John W7CD

  

From: Bill [mailto:brightl...@gmail.com] 
Sent: Saturday, May 23, 2020 3:59 PM
To: WSJT software development
Subject: Re: [wsjt-devel] (no subject)

  

Hi,

  

    Thanks for the quick response. I just tried HandShake = NONE and I have the 
same result - Rig Failure - HamLib Error.

  

   Any other suggestions?

  

Thanks!

  

Bill - AK6A

  

On Sat, May 23, 2020 at 3:32 PM Bill Somerville <g4...@classdesign.com> wrote:


On 23/05/2020 23:16, Bill wrote:


I am having an issue connecting a Yaesu FTDX-101MP to WSJT-X on a Mac. I’m able 
to get the receive Audio Codec to work properly and I can see decodes but I get 
a “Rig Failure - Hamlib Error - Invalid configuration while opening connection 
to rig” whenever I do a Test CAT. I am unable to get WSJT-X to establish 
control communications with the radio. I’ve seen online suggestions that say 
use the HamLib FT-991 selection. I am using the regular WSJT-X version 2.1.2. I 
am also just using a USB cable from the radio to the Mac which is running High 
Sierra. I am using the following settings:

  

WSJT-X

  

RADIO TAB

  

Rig: Yaesu FT-991

  

Serial Port: /dev/cu.SLAB_USBtoUART1 

Note: Installed latest Silicon Labs Drivers - Also Available selections:

/dev/tty.SLAB_USBtoUART1

/dev/cu.SLAB_USBtoUART

/dev/tty.SLAB_USBtoUART

  

Baud Rate: 38400

Polling Interval: 1S

Data Bits: Eight

Stop Bits: Two

Handshake: Hardware

Force Control Lines: Both Empty

  

PTT Method: CAT

Mode: None

Split: Rig

  

AUDIO Tab

  

Input - USB AUDIO CODEC
Output - USB AUDIO CODEC

FTDX101MP Menu

  

FUNC --> Operation Settings
General
232C RATE - 38400
CAT RATE - 38400

FUNC --> RADIO SETTINGS
MODE SSB
SSB MOD SOURCE - REAR
REAR SELECT - USB
RPORT GAIN - 10
DATA MODE SOURCE - REAR (This is the default)
REAR SELECT - USB
DATA OUT LEVEL - 10
RPORT GAIN - 10

RADIO MAIN PANEL & DISPLAY

  

  

R.FIL - 3kHz
WIDTH - 4000Hz


APPLE COMPUTER

  

USB AUDIO CODEC 1 Format: 2 ch 16-bit Integer 48 kHz
USB AUDIO CODEC 2 Format: 2 ch 16-bit Integer 48 kHz

  

  

  

Any ideas what might be the issue in getting this going? Has anyone else been 
able to get a FTDX-101MP working with WSJT-X? Do I need to install a newer 
version of HamLib for this new radio?

  

Thanks!

  

Bill - AK6A


Hi Bill,

try with "Settings->Radio->Handshake->None".

73
Bill
G4WJS.

_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel




_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel

_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
  
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel

Reply via email to