After the latest MP FW update, wsjtx 2.1.2, and using Data-U designed
for this purpose re WSJTX, the setup is simple, especially using both
the enhanced compors for CAT and standard
comport for Ptt via RTS. It works great.
On 24/5/20 3:28 pm, Ken Chandler via wsjt-devel wrote:
I had issues to but on window 10 platform.
I used the FT5000 rig, everything burst into life when I switched over
from FTdx101D
Ken.. G0ORH
Sent from my iPad
On 24 May 2020, at 01:02, John Zantek <j...@zantek.net
<mailto:j...@zantek.net>> wrote:
Bill,
Many new 101MP owners in the PNW have been experiencing some setup
issues, resulting in lots of phone calls.
Have you been able to talk to the rig with any other S/W via USB and
with what virtual settings?
Is the PC using USB 2.0 or 3.x ? The 101MP is unfortunately
persnickety in that regard.
No hubs, right?
73 John W7CD
*From:*Bill [mailto:brightl...@gmail.com]
*Sent:* Saturday, May 23, 2020 3:59 PM
*To:* WSJT software development
*Subject:* Re: [wsjt-devel] (no subject)
Hi,
Thanks for the quick response. I just tried HandShake = NONE and
I have the same result - Rig Failure - HamLib Error.
Any other suggestions?
Thanks!
Bill - AK6A
On Sat, May 23, 2020 at 3:32 PM Bill Somerville
<g4...@classdesign.com <mailto:g4...@classdesign.com>> wrote:
On 23/05/2020 23:16, Bill wrote:
I am having an issue connecting a Yaesu FTDX-101MP to WSJT-X
on a Mac. I’m able to get the receive Audio Codec to work
properly and I can see decodes but I get a “Rig Failure -
Hamlib Error - Invalid configuration while opening connection
to rig” whenever I do a Test CAT. I am unable to get WSJT-X
to establish control communications with the radio. I’ve seen
online suggestions that say use the HamLib FT-991 selection.
I am using the regular WSJT-X version 2.1.2. I am also just
using a USB cable from the radio to the Mac which is running
High Sierra. I am using the following settings:
WSJT-X
RADIO TAB
Rig: Yaesu FT-991
Serial Port: /dev/cu.SLAB_USBtoUART1
Note: Installed latest Silicon Labs Drivers - Also Available
selections:
/dev/tty.SLAB_USBtoUART1
/dev/cu.SLAB_USBtoUART
/dev/tty.SLAB_USBtoUART
Baud Rate: 38400
Polling Interval: 1S
Data Bits: Eight
Stop Bits: Two
Handshake: Hardware
Force Control Lines: Both Empty
PTT Method: CAT
Mode: None
Split: Rig
AUDIO Tab
Input - USB AUDIO CODEC
Output - USB AUDIO CODEC
FTDX101MP Menu
FUNC --> Operation Settings
General
232C RATE - 38400
CAT RATE - 38400
FUNC --> RADIO SETTINGS
MODE SSB
SSB MOD SOURCE - REAR
REAR SELECT - USB
RPORT GAIN - 10
DATA MODE SOURCE - REAR (This is the default)
REAR SELECT - USB
DATA OUT LEVEL - 10
RPORT GAIN - 10
RADIO MAIN PANEL & DISPLAY
R.FIL - 3kHz
WIDTH - 4000Hz
APPLE COMPUTER
USB AUDIO CODEC 1 Format: 2 ch 16-bit Integer 48 kHz
USB AUDIO CODEC 2 Format: 2 ch 16-bit Integer 48 kHz
Any ideas what might be the issue in getting this going? Has
anyone else been able to get a FTDX-101MP working with
WSJT-X? Do I need to install a newer version of HamLib for
this new radio?
Thanks!
Bill - AK6A
Hi Bill,
try with "Settings->Radio->Handshake->None".
73
Bill
G4WJS.
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
<mailto:wsjt-devel@lists.sourceforge.net>
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
<mailto:wsjt-devel@lists.sourceforge.net>
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel