Lance, Thanks – but the issue is that the operation and displayed results – changed! It first was showing, on the Echo graph centered (0). And at the same time it showed on the wide graph as the echo was where it should be – i.e. 1596Hz for a 96Hz echo doppler shift. And it decoded a signal with a level provided (-14.6, twice, w/ a Q of 10!).
But then later – w/o changing anything other than time (i.e. later)… the echo showed on the Echo graph at -93 Hz (now the expected echo was 93 Hz)… the wide graph showed it just above 1500Hz and although there was clearly an echo – the tabulated results remained at a level of -99.9! This is all clear in the screen shot if anyone wants to see it. After reading the doc I did see that it was set to “on own echo”. I changed that to “none” and now it seems to work as expected – the echo is now at 1576Hz on the wide graph and is at +76Hz on the Echo graph – and it gave a proper numeric value (this time -20.3). So again – its that it changed and when it changed it was no longer functional as, even though the echo was clearly there, the value for SNR was ‘stuck’ at -99.9. Gary Sent from Mail for Windows From: Lance Collister, W7GJ via wsjt-devel Sent: Wednesday, February 22, 2023 11:57 AM To: K9RX via wsjt-devel Cc: Lance Collister, W7GJ Subject: Re: [wsjt-devel] Possible issue with ECHO mode - 2.6.0 Hi Gary, I have not followed the ECHO mode documentation, but it may be that on the Wide Graph, you see the trace coming back as doppler shifed, but (at least in previous versions) the ECHO mode moves the frequency around, along with its receiver, and just displays the sum total of the average echoes received. The program knows where it is transmitting, so knows where to listen for the signal. I don't think you need to pay any attention to what is shown on the Wide Graph...GL and VY 73, Lance On 2/22/2023 16:13:35, K9RX via wsjt-devel wrote: > > Thank you – I’ll look this over to see if it addresses the echo appearing > differently in both the wide and echo graph. > > Gary > > Sent from Mail <https://go.microsoft.com/fwlink/?LinkId=550986> for Windows > > *From: *Charles Suckling via wsjt-devel > <mailto:wsjt-devel@lists.sourceforge.net> > *Sent: *Wednesday, February 22, 2023 10:53 AM > *To: *WSJT software development <mailto:wsjt-devel@lists.sourceforge.net> > *Cc: *Charles Suckling <mailto:g3w...@gmail.com> > *Subject: *Re: [wsjt-devel] Possible issue with ECHO mode - 2.6.0 > > Hi Gary > > Have a look at these, which will hopefully help. > > https://wsjt.sourceforge.io/Echo_Mode_in_WSJT-X_2.6.0.pdf > > http://www.bobatkins.com/radio/EME_WSJTX_echo_mode_basic_guide.html > > 73 > > Charlie DL3WDG > > On Wed, 22 Feb 2023 at 16:37, K9RX via wsjt-devel > <wsjt-devel@lists.sourceforge.net> wrote: > > I like to use ECHO to test the station on 6M EME. > > But the latest version has changed enough I was wondering if there was a > short > help file for it? > > Also: The Echo graph will at times show the echo centered – and other > times > show it offset. I have a jpg showing a recent echo run where the echo was > very > strong – and it was showing it as the right numeric doppler shift, 96 Hz, > but > it was showing it on the graph as -96Hz and there was no SNR value > reported > (-99.0 shown). You can see the echo on the wide graph – you can see the > echo on > the echo graph – but both have it lower than it should be… > > A few minutes earlier I had 2 echos at -14.6 and others in to the low > 20’s – > these were all showing on the spreadsheet – and “properly” on both the > wide and > echo graphs. > > Gary Myers > > K9RX > > Sent from Mail <https://go.microsoft.com/fwlink/?LinkId=550986> for > Windows > > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel > > > > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel -- Lance Collister, W7GJ(ex WA3GPL, WA1JXN, WA1JXN/C6A, ZF2OC/ZF8, E51SIX, 3D2LR, 5W0GJ, E6M, TX5K, KH8/W7GJ, V6M, T8GJ, VK9CGJ, VK9XGJ, C21GJ, CP1GJ, S79GJ, TX7MB, TO7GJ) P.O. Box 73 Frenchtown, MT 59834-0073 USA TEL: (406) 626-5728 QTH: DN27ub URL: http://www.bigskyspaces.com/w7gj Skype: lanceW7GJ 2m DXCC #11 - 6m DXCC #815 - FFMA #7 Interested in 6m EME? Ask me about subscribing to the new Magic Band EME email group, or just fill in the request box at the bottom of my web page (above)! _______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
